1. Converting & Laminating Tricks of The Trade Ramesh Lhila, Technical Director, Venture Tape Rebecca Blose, Technical Manager, CCT Scott Lindberg - Technical Sales, Syntac Patrick Eaton, Technical Director, Syntac April 2008

2. Presentation Outline  Laminating Adhesives  Release Liners  Static Control in Web Handling  Handling Adhesive Build Up on Idler/Tools  Brief Overview of Topics Followed by Panel Discussion/Q&A

3. Laminating Adhesives

4.  In Flexible Packaging Industry – “Liquid” Adhesive, Laminating Two Substrates  In GFA Related Industry – Transfer Tape or Double-Coated Tape Supplied on a Liner with Various Supports (Backing) Film Tissue Scrim, Fabric etc. Terminology

5. Adhesive Types  Pressure Sensitive – Applied By Pressure and/or Supported By Heat Rubber- Resin Acrylic Silicone Other Specialty Including Blends  Heat Seal – Bonding Requires Heat Broad Range of Materials

6. Adhesive Selection Factors  Tack and Peel  Cost Rubber > Acrylic > Silicone  Cohesive Strength at Elevated Temperature  UV Resistance  Service Temperature Range Silicone > Acrylic > Rubber

7. Substrate Factors  Substrate Chemistry Surface Energy of the Material (Low or High)  May Need Heat and/or Pressure Presence of Plasticizers, Oils, Slip Agent etc.  Adhesive Selection is Important Surface Type  Metal, Plastics, Foam, Rubber etc.  Surface Quality Smooth, Textured, or Porous  Need to Adjust Adhesive Thickness for Optimal Wet Out

8. Release Liners

9. Release Liner - Technology  Most Liners are Silicone Coated Cured Via Thermal, U-V or E-B Processes  Specialty Liners Fluoro-Silicone Chemistry Based  Non-Silicone Liners Limited Applications

10. Release Liner - Technology  Release Coatings Applied Via Emulsion, Solvent or 100% System  Release Level Controlled By Type of Silicone Chemistry Application Method Control Release Additives

11. Release Liner - Substrates  Paper Super-calendered Kraft (SCK) Glassine Clay Coated MF, MG and Latex Saturated Paper  Poly Coated Paper (LDPE, HDPE,PP) One-Side Poly Coated Two-Side Poly Coated  Films Polyolefin – LDPE, HDPE, BOPP, Cast PP Polyester - PET

12. Liner Substrate Considerations  Paper Liner  Very Good Temperature Resistance Super-calendered Kraft  Prone to Cockling in Humid Environment  Die Cuttable Glassine  Good Caliper Control  Semi-Transparent  Excellent For Die Cutting Clay Coated  Can Be Brittle  Somewhat Moisture Stable

13. Liner Substrate Considerations  Film Liners  Usually higher cost Polyolefin and Blends  Soft, extensible, smooth, good tear resistance  Possible to get variety of colors  Temperature sensitive Polyester  Handles high temperature, good tear resistance  Excellent die cutting surface  Excellent caliper control

14. Liner Substrate Considerations  Poly-coated Liner  Very good resistance to moisture and cockling  Can be gloss/matte (common) or gloss/gloss  Somewhat heat sensitive

15. Liner Release Considerations  Liner Release Easy release needed for many low density PU and melamine foams  Need adhesive to stay with the foam Tighter Release for Stiffer Materials  Do not want the liner to buckle Stable Release  Prevent adhesive lockup on aging and high temperature exposure

16. Static Controls in Web Handling

17. Static / Static Electricity Relating to or producing Stationary Charges; Electrostatic May be observed as a small ‘spark’ that jumps from one surface to another from build-up between positively and negatively charged areas.

18. Concerns / Dangers  Static Tinsel / String quick & easy must touch web  Carbon Fiber Brushes technical, effective very cost effective  Ionized Air / Static Blowers neutralizes static charge  Ionized Bars permanently mounted over web  Static Tinsel / String quick & easy must touch web  Carbon Fiber Brushes technical, effective very cost effective  Ionized Air / Static Blowers neutralizes static charge  Ionized Bars permanently mounted over web Contamination: Attraction of dust and dirt particulates to your web.

19. Concerns / Dangers:  Safety: If a roll of paper, film or PSA tape is low to the floor or unwind equipment is not properly grounded, arch may jump & cause shocks and / or discomfort to your operators Wrist Straps Floor Mats Heel Grounds  If any flammables; solvents, lubricants, adhesives, cleaners are present, must maintain a static free environment to prevent sparks from igniting (minimally)  Safety: If a roll of paper, film or PSA tape is low to the floor or unwind equipment is not properly grounded, arch may jump & cause shocks and / or discomfort to your operators Wrist Straps Floor Mats Heel Grounds  If any flammables; solvents, lubricants, adhesives, cleaners are present, must maintain a static free environment to prevent sparks from igniting (minimally) Note: Paper liner selection lowers risk of static. Much higher charge from film liners.

20. How to Handle Adhesive Build Up on Idlers / Tooling

21. Adhesive Build Up  Adhesive that is pulled away from the tape or web and builds up on unwanted surfaces AKA edge pick, ooze  Increased Clean-Up, Change-Over and Labor Costs  Contamination of other webs Typically impacts Rotary Die-Cutters Not a lot of complaints with Steel Rule or Preco None with Laser converting. Deposit = Residue

22. Prevention  Lubricants  Chemically Coated or Treated Dies and Rolls (initial cost, but longevity)  Knife Selection / Design  Oil Wells  Materials of Construction  Talcs / Powders (on edges of web Reduces pick/flow)  Die Packing – as tooling wears, need to prevent increase in ‘gapping’  Environment (hot = flow; cold = stiffer)  Lubricants  Chemically Coated or Treated Dies and Rolls (initial cost, but longevity)  Knife Selection / Design  Oil Wells  Materials of Construction  Talcs / Powders (on edges of web Reduces pick/flow)  Die Packing – as tooling wears, need to prevent increase in ‘gapping’  Environment (hot = flow; cold = stiffer) ENSURE THAT ANY prevention methods do not impact desired performance of your PSA or converted part.

23. Tape Selection May considerably impact the buildup or edge pick issues that plague the industry Adhesive Thickness Transfer Film versus Double-Coat  Carrier Chemistry  Rubber versus Solvent May considerably impact the buildup or edge pick issues that plague the industry Adhesive Thickness Transfer Film versus Double-Coat  Carrier Chemistry  Rubber versus Solvent

24. Environmental Factors Affecting PSA Tapes and Liners

25. Environment  Solvent & Chemicals Adhesive swelling, softening or dissolve / deaden / degrade Crack / degrade release chemistry  Grease, Oil and Mold Releases May impact adhesive and liner similarly: Creating a barrier between the PSA and liner and/ or PSA and substrate

26. Temperature Exposure  Low temperatures can have a negative effect on adhesives: Firms and makes adhesives brittle Reduce adhesive tack (winter months) Increase shock sensitivity – Static between liner and PSA during converting Desire good glass transition  High temperatures can have a negative effect on adhesives: Adhesive softening – Edge Ooze / Bleeding Reduce shear strength Reduce cohesive strength  Low temperatures can have a negative effect on adhesives: Firms and makes adhesives brittle Reduce adhesive tack (winter months) Increase shock sensitivity – Static between liner and PSA during converting Desire good glass transition  High temperatures can have a negative effect on adhesives: Adhesive softening – Edge Ooze / Bleeding Reduce shear strength Reduce cohesive strength

27. Temperature Exposure  Humidity Liner Cockling / Wrinkling (high) Cracking / Breaking (low) Increased static  UV Light Exposure  Cleanliness / Housekeeping Contamination may also create barriers  Humidity Liner Cockling / Wrinkling (high) Cracking / Breaking (low) Increased static  UV Light Exposure  Cleanliness / Housekeeping Contamination may also create barriers

28. Know the environment that your PSA will be exposed to in both you and your customer’s facility and end use application. Select the adhesive and liner that will be robust enough to BEST meet all above conditions!!!!

30. Questions