1. M. Nelson, 21 Mar. 2010 NorthWest Louisiana Autonomous Robotics Competition (NWLA-ARC) 2 Challenges – 4 Bottle Race – Board Challenge Awards for Event Winners and Overall Grand Champion in each Division.

2. General Rules All work to be accomplished by students. Students may change hardware / software between events – A team can have a different robot for each event or make changes to a single robot. M. Nelson, 21 Mar. 2010

3. NWLA-ARC 4-Bottle Race 2010 Start behind front edge of tape as shown. Timers start on “go.” Timers stop when front of bot crosses finish line. (Each bot timed separately) No deduction for striking bottles. Crossing Foul Line and contacting the other bot results in a “no time” run (DQ). Best time from 2 runs wins. Start / Finish Line

4. M. Nelson, 21 Mar. 2010 NWLA-ARC Board Challenge 2010 2 Scored Runs Per Team 3 Minute Time Limit Per Run Highest score from 2 runs wins. Base (Start) Area 1 Large Drums Holding Area 4 Holding Area 3 Holding Small Drums Holding Area 2 Small Drums NXT Balls Up The Ramp “Tee” Large Drums

5. Board Challenge Scoring M. Nelson, 21 Mar. 2010 TaskPoints EachTotal # Possible Total Score Possible Large Drums in Area 12510 Large Drums in Area 24520 Small Drums in Area 12714 Small Drums in Area 24728 Balls off of Pedestals6212 Tee in Area 36212 Tee in Area 415230 Finish in Base818 Finish in Area 4101 Deductions-4-- Maximum Points per Run100 Best individual run score from 2 timed runs (3:00 min. each) Total Score of 2 runs for tie breaker

6. M. Nelson, 21 Mar. 2010 Board Challenge Rules Start with 2 wheels in Base. (apparatus can hang over line) Bots can return to base (autonomously) for adjustments at no cost. (Any part of the bot over the line – no tethers) PVC parts under bot control can be manipulated while the bot is in base. – Bot can push/pull PVC parts back to base and operator can move them to place them back under bot control as it leaves base If Bot is touched it must return to Base. (4 point deduction per occurrence) Black line is “in bounds”. (score points if object is on the line) – All of the barrel must be on the line, not just part touching. If any of the barrel is outside the black line, the barrel is NOT in.

7. Combined Scoring (Grand Champions) 4- Bottle Race: Points awarded for final finish position: – 1st Place: 20 points – 2 nd Place: 18 points – 3 rd Place: 16 points – … Board Challenge: Points awarded equal best run score for each team. – (see Board Challenge Scoring chart) M. Nelson, 21 Mar. 2010 Total Score = 4-Bottle Race Points + Board Challenge Points

8. M. Nelson, 21 Mar. 2010 4-Bottle Race Course Layout Blue Painter’s Tape (3/4”) 6 ft. 12 ft. Center (Foul) Line Bottles centered on 12” x 12” floor tiles as shown. 1 Liter Water Bottles (Full)

9. M. Nelson, 21 Mar. 2010 8’ 4’ Board Challenge Field of Play 1’ 2 x 4 Lumber ~3/4” Painted Lines (Flat Black) Plywood Base – Painted White (sand / fill large bumps / holes) Base (Start) Area 1 Large Drums* Holding Area 4 Board Materials List: (1) ~5/8” - Plywood Base (4’ x 8’) (2) 93” - 2x4 Studs (2) 48” - 2x4 Studs (1) ¾” x ¾” x 5½“ Cleat (1) ¾” x ¾” x 4¾“ Cleat Holding Area 3 Holding Small Drums Holding Area 2 Small Drums NXT Balls Up The Ramp “Tee” *Large Drums are laid on their sides.

10. M. Nelson, 21 Mar. 2010 8’ 4’ Board Challenge Part Placement 1’ Base (Start) Area 1 Large Drums* Holding Area 4 Holding Area 3 Holding Small Drums Holding Area 2 Small Drums NXT Balls “Tee” *Large Drums are laid on their sides. 10½” 3½” 6” 5¼” 10½” 5¼” Black lines centered between walls. 4”

11. 5-½“ Board Challenge Holding Areas 1 and 2 Detail M. Nelson, 21 Mar. 2010 1’ Area 1 Holding Area 2 7“ ¾” x ¾” Cleats 5“ Cleat – ¾” x ¾” x (length) of lumber ripped from standard 1 x 4 stock.

12. M. Nelson, 21 Mar. 2010 Up The Ramp Side View (Left) Front View Top View Side View (Right) Right Left Ramp Materials List: (8) 8½” 2x4 Studs (4) 20½“ 2x4 Studs (2) 12” x 24” 3/16” Wall Board (2) 12” x 12” 3/16” Wall Board (3) ~ ¾” x ¾” x 12” Cleats Board Challenge Ramp Detail / Construction Holding Area 4 2x4 Studs Wall Board Cleat 3” 48” 24” Ramps should be level with the tops of the platforms. Transitions to be sanded / filled as needed.

13. M. Nelson, 21 Mar. 2010 Board Challenge Components 2” 1-1/8 ” Large Drum (5) ¾” PVC 1-1/8” Small Drum (7) ½” PVC Cap May be rounded “Tee” (2) (PVC Tee w/pipe in each end) ½” PVC All Parts Schedule 40 PVC * Lightly sand / round edges to limit hang-ups on board surface. ¾” Ball / Pedestal (2) ½” PVC 1” 7/8”