1. Cherrill Spencer, SLAC. MDI Workshop Jan '05 1 Impact of Crossing Angle Value on Magnets near the IP Overview of several unusual quadrupole designs that may be used to satisfy some stringent spatial requirements on magnets near the interaction point. CHERRILL SPENCER, ILC@SLAC Y. IWASHITA, KYOTO UNIVERSITY, JAPAN. Showing the need for early and close collaboration between accelerator physicists developing beamline lattices and magnet engineers.

2. Cherrill Spencer, SLAC. MDI Workshop Jan '05 2 Relative positions of the incoming & extraction magnets L*=TBD For 2mr :Incoming & extracted beams pass through QD0. Extracted beam gets extra kick of ~4 mrad Extracted beam passes through 3 quads QD0 Probably superconducting Warm quads in incoming beamline Crossing angle: TBD Distance TBD For 2mr ~ Crossing angle+4 mrad TBD=To be Determined ∆x is horizontal distance between the centers of the 2 beamlines Interaction Point Photon beam

3. Cherrill Spencer, SLAC. MDI Workshop Jan '05 3 Extraction quad requirements with a 20mr crossing angle. To minimize beam size, quad apertures and dimensions in the extraction line, the quad focusing has to start soon after the IP. Even so the beam width gets very large. But, the first extraction quad has to be placed at sufficient distance from IP where it can realistically fit without interference with elements of the incoming beamline. Two options of extraction optics are compared below - with 8 and 15 m space between IP and the first extraction quad. Lattices from Yuri Nosochkov, SLAC

4. Cherrill Spencer, SLAC. MDI Workshop Jan '05 4 Unusual Quad Styles for areas with close adjacent beams ~221mm Field-free region for secondary beam. Primary beam passes through center of regular quad, bore radius=35mm Quad for HERA Luminosity Upgrade. 726 mm Q2 in PEPII 368mm Field-free region for secondary beam. Primary beam passes through center of regular quad, bore radius=47.8mm ~142mm

5. Cherrill Spencer, SLAC. MDI Workshop Jan '05 5 Extraction quad requirements with a 2mr crossing angle. If the crossing angle is only 2mr then the horizontal distance between the incoming and extracted beam, ∆x, becomes even smaller, forcing even stranger quadrupole designs. For example, based on a very preliminary and not fully- developed lattice with a 2 mr crossing angle and the first extraction quad at 10m from the IP (lattice from Yuri Nosochkov) these are the requirements on the first three extraction quads, for 250Gev/beam: QuadL (m)GL(T)R mm ∆ x mm QFEX14.143127.95677 QDEX24.161-166.456108 QFEX32.07282.963131 This set of magnet requirements is just one of many possible sets. Difference between ∆x and R is approximate space available for coil packet and core backleg in a conventional quad- NOT enough space in any of these 3 quads, so need to consider atypical quad designs.

6. Cherrill Spencer, SLAC. MDI Workshop Jan '05 6 Septum Half Quad from TESLA TDR for 1 st extraction quad 350mm 110mm Incoming beam passes throu’ notch in steel septum. Septum thickness=10mm. Field here needs to be <~20G. Precision engineering needed to achieve this. Design is based on a HERA luminosity upgrade quad. Bore radius = 75mm. Extracted beam passes through HALF quad to the right of its center and so beam sees a dipole field on top of the quad field. The magnet’s effect on the beam shape has to be modelled using some field data from a magnet simulation program. Extracted beam horizontal profile is NOT Gaussian, nevertheless outlying particles will hit face of magnet if half-aperture is too small. Steel septum In my opinion one cannot satisfy QFEX1 requirements with such a design. When 2mr reqts are finalized I will make a detailed model.

7. Cherrill Spencer, SLAC. MDI Workshop Jan '05 7 Side-by-side Quads: a different approach, using permanent magnets Idea from Y.Iwashita, Kyoto University Conceptual figure: PANDIRA model. Very preliminary. NEOMAX46 pm bricks Permendur, soft mag material QD QF Vary gap height to vary gradient Sides are open X=0 Have full quad fields in both beamlines.

8. Cherrill Spencer, SLAC. MDI Workshop Jan '05 8 Gradient variation with x for side-by-side quads Gradient varies along x : has sextupole component. Maximum value of ~100T/m at x=+-10mm QD QF Possible way to have 2 quads in very close adjacent beamlines.

9. Cherrill Spencer, SLAC. MDI Workshop Jan '05 9 Conclusions on Magnet Design for near IP Magnets and Comments on Process The requirements for the first few magnets near the IP, in both the incoming and extraction beamlines, are very stringent from an engineering point of view. The spatial constraints associated with any small crossing angle, especially a 2mr scenario, lead to quads that are on the cusp of being feasible to fabricate. Lattice designers must not generate new extraction beam lattices without giving the basic quad requirements to a magnet engineer for them to check their feasibility & make designs and computer models- and the fields predicted by the models should be used by the lattice designers in their tracking studies. How to match up accelerator physicists and magnet engineers can be discussed during last session of this workshop.