1. 1 © 2003, Cisco Systems, Inc. All rights reserved. CCNA 2 Module 4 Learning About Other Devices

2. 222 © 2003, Cisco Systems, Inc. All rights reserved. Cisco Discovery Protocol (CDP) can build a basic picture of a network. CDP is media and protocol independent, and runs on all Cisco equipment. CDP is used to obtain information about neighboring devices, such as the types of devices connected, the router interfaces they are connected to, the interfaces used to make the connections, and the model numbers of the devices.

3. 333 © 2003, Cisco Systems, Inc. All rights reserved. Cisco Discovery Protocol (CDP) CDP is a Layer 2 protocol that connects lower physical media and upper network layer protocols. CDP Version 2 (CDPv2) is the most recent release of the protocol. Cisco IOS Release 12.0(3)T or later supports CDPv2. CDP Version 1 (CDPv1) is enabled by default with Cisco IOS Release 10.3 to 12.0(3)T.

4. 444 © 2003, Cisco Systems, Inc. All rights reserved. Cisco Discovery Protocol (CDP) When a Cisco device boots up, CDP starts up automatically and allows the device to detect neighbor devices that use CDP. CDP operates at the data link layer and allows two systems to learn about each other, even if they use different network layer protocols. Each device that is configured for CDP sends periodic messages, which are known as advertisements, to directly connected Cisco devices. The advertisements also contain time-to-live or holdtime information, which indicates the length of time that receiving devices should hold CDP information before they discard it.

5. 555 © 2003, Cisco Systems, Inc. All rights reserved. Showing CDP Neighbor Entries Use the show cdp neighbors command to display CDP updates on the local device.

6. 666 © 2003, Cisco Systems, Inc. All rights reserved. The show cdp neighbors Command

7. 777 © 2003, Cisco Systems, Inc. All rights reserved. Implementation, Monitoring, and Maintenance of CDP

8. 888 © 2003, Cisco Systems, Inc. All rights reserved. The cdp run Command & Disabling CDP

9. 999 © 2003, Cisco Systems, Inc. All rights reserved. The clear cdp counters Command

10. 10 © 2003, Cisco Systems, Inc. All rights reserved. The show cdp Command

11. 11 © 2003, Cisco Systems, Inc. All rights reserved. The show cdp entry Command

12. 12 © 2003, Cisco Systems, Inc. All rights reserved. The show cdp interface Command

13. 13 © 2003, Cisco Systems, Inc. All rights reserved. Creating a Network Map The show cdp neighbors [type number] [detail] command can be used to obtain the following: – Device ID — Address – Port ID — Capabilities – Version — Platform – IP network prefix – VTP management domain name (CDPv2 only) – Native VLAN (CDPv2 only) – Full/Half duplex (CDPv2)

14. 14 © 2003, Cisco Systems, Inc. All rights reserved. Troubleshooting CDP

15. 15 © 2003, Cisco Systems, Inc. All rights reserved. Telnet Telnet is a virtual terminal protocol that is part of the TCP/IP protocol suite. It allows connections to be made to remote hosts. The verification of application layer connectivity is a by- product of Telnet.

16. 16 © 2003, Cisco Systems, Inc. All rights reserved. Telnet Operations

17. 17 © 2003, Cisco Systems, Inc. All rights reserved. Advanced Telnet Operation Multiple Telnet sessions can be used and suspended by using the Ctrl+Shift+6 and x sequence.

18. 18 © 2003, Cisco Systems, Inc. All rights reserved. Commands Related to Telnet

19. 19 © 2003, Cisco Systems, Inc. All rights reserved. Testing with the ping Command Each exclamation point (!) indicates a successful echo. Each period (.) on the display indicates that the application on the router timed out while it waited for a packet echo from a target.

20. 20 © 2003, Cisco Systems, Inc. All rights reserved. Testing with the traceroute Command The traceroute command will attempt to reach the next step until the Ctrl-Shift-6 escape sequence is used.

21. 21 © 2003, Cisco Systems, Inc. All rights reserved. Troubleshooting IP Addressing Issues ping uses the ICMP protocol to verify the hardware connection and the IP address of the network layer. telnet verifies the application layer software between a source and a destination. traceroute locates failures in a path from a source to a destination. This command uses Time to Live values to generate

22. 22 © 2003, Cisco Systems, Inc. All rights reserved. Summary