1. RSVP AGS Upgrade Projects 1.4.4 MECO RSVP Preliminary Baseline Review Brookhaven National Lab April 6-8, 2005 D. Phillips

2. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review2 MECO Cost (Burdened $’s)

3. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review3 AGS Beam Specifications MECO AGS Beam Specifications: –Momentum = 7.5 GeV/c –Spill length = 0.5 sec –Rep rate = 1.0 sec –Intensity Experiment goal = Two bunches/AGS cycle 20TP/bunch AGS base-line (achievable) = 20 TP/sec –Time between bunches = 1350 nsec –Beam bunch width = 30 nsec full width –Extinction between bunches = 1E-9 –Beam hours: engineering run = 800 hours physics run –2800 hours at 40 TP/spill (stretch goal) –5600 hours at 20 TP/spill (base plan) total integrated protons for physics run = 4.0E20 –Caveat = run time will depend on achievable muon flux, actual background rates etc..

4. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review4 Targeting Requirements Muon Yield: The target must be compact and have minimal material around it to avoid reabsorbing pions from the primary interaction before they produce muons. Extinction: The dimension of the target transverse to the beam should be small to minimize the phase space for protons intercepting the target after receiving less than the maximal kick in the RFMM Beam Spot: the preceding requirements imply a small (  radius  1 mm) beam spot in order to keep ~95% of the beam on the target Aperture Limits: The beam must pass through the complex region of the PS – TS interface. The area available for the beam is limited. Particularly as shielding is needed to protect the coils from beam fault conditions. Adjustability: the field in the MECO solenoids can be reversed for calibration studies, but the beam must still strike the target. The downstream beam steering magnets must accommodate the difference in incoming trajectory needed for this.

5. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review5 Construction Requirements Transport Proton Beam from AGS to Proton Target. Provide for installation of RF Modulated Magnet and Extinction Measurement Equipment. Provide MECO Experimental and Solenoid System Infrastructure. Meet OSHA, NFPA and BNL Safety Requirements. Meet BNL Radiological Control Requirements. Meet Suffolk County Article 12 Drinking Water Standard.

6. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review6 MECO Final Installation RefrigeratorCounting House RF Modulated Magnet (RFMM) Detector Solenoid (DS) Lambertson Magnets Compressors Production Solenoid (PS) & Proton Target Beamline Power Supplies Solenoid Power Supplies Valve Box Transport Solenoids (TSu & TSd) MECO Detectors (Removed from DS) A-Line Primary Proton Beam Proton Target Cooling System Beam Stop Electronics Hut

7. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review7 MECO Ready for Beam Tests & Solenoid Installation RefrigeratorCounting House RFMM Test Module Target Test Station Beamline Power Supplies Solenoid Power Supplies Valve Box MECO Detectors (Removed from DS) A-Line Primary Proton Test Beam Electronics Hut Temporary Beam Stop Compressors

8. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review8 Upstream Proton Target Area Production Solenoid (PS) Proton Target Last Target Focusing Quadruple Pitching Magnets Movable Solenoid Shield Muon Beamline Warm Bore Vacuum Transport Solenoid (TSu) PS Pole Piece & Return Yoke TSu Cold Mass Support TSu Cold Mass Support PS Cold Mass Supports

9. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review9 Downstream Proton Target Area Helium Box to Beam Stop Proton Target PS Vacuum End Cap Target Access Port “Thin” Window Target View Port Rad Hard Camera Heat & Radiation Shield Muon Beamline Warm Bore Vacuum Vacuum Pump Port Vacuum Seal Heat & Rad Shield Cooling Feedthru Proton Beam

10. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review10 MECO Roll-up

11. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review11 MECO Schedule

12. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review12 MECO Schedule

13. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review13 1.4.4 MECO Cost $372k Shielding Purchase $172k LN2 Tank Purchase Moving to 1.5 $95k Rigging $103k Royals $87k Cable

14. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review14 1.4.4 MECO Work

15. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review15 Major Milestones A-Line Ready for MECO Beam Tests – 10/1/08 –This is one year sooner than needed Design Review of A-Target Area – 1/15/09 –Major functional & ALARA concerns A-Line Ready for Solenoid Installation – 4/1/08 –Allows Solenoid Systems installation to begin A-Line Ready for Beam to MECO – 6/1/11 –WBS 1.4.4 MECO is complete

16. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review16 Low Level Milestone - Magnets

17. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review17 Magnet Monitor Cost Example Materials from Cost Book: From MS Project (Direct Costs): Labor is Engineering Judgment

18. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review18 Refurbish Magnets Cost Example Magnet Materials – From cost book: –Mechanical $1050 –Electrical $303 –Not all magnets need all parts, engineering judgment use $1000/magnet Labor is engineering judgment from experience refurbishing magnets From MS Project (Direct Costs):

19. April 6-8, 2005D. Phillips RSVP Preliminary Baseline Review19 Electronics Hut Cost Estimate Building Purchase based on 3/04 quote for a similar building ($99,250/480 sq ft = $210/sq ft) Building purchased complete with HVAC, Fire Alarm System, Power & Lights. Labor is engineering judgment. From MS Project (Direct Costs):