1. 1 HD EIE 42075 88M -108MHz Phase Lock Loop FREQUENCY SYNTHSIZER WONG TANG PAAI DILLIAN 01111911D WONG WAI TING KENNETH 01901021D

2. 2 Content 1.Introduction 2.Process 3.Example 4.Difficulties 5.Problem Solving 6.Achievement 7.Improvement

3. 3 Introduction

4. 4 VHF phase Lock Loop frequency synthesizer Use the feedback and frequency comparator, to detect input frequency and send an error signal to request the change of frequency. When the input frequency is appropriate, the error signal will goes stables, and the frequency is locked. The frequency is actually generated by Voltage Control Oscillator.

5. 5 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1000 Comparator Reference frequency RC tank circuit Change the phase input into DC offset Variable Register R, N ~V ~f

6. 6 Process

7. 7 8051 Programming Voltage Control Oscillator Low Pass Filter Frequency synthesizer Phase Lock Loop

8. 8 Example

9. 9 LPF VCO & Buffer 8051 ÷ R=? ÷ N=? Comparator 12MHz R=120,N=1000 ~V ~f

10. 10 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1000 Comparator 12MHz 100kHz 10V 105.8MHz 105.8kHz ΔΦ 1

11. 11 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1000 Comparator 12MHz 100kHz 8V 103.8MH z 103.8kHz ΔΦ 2

12. 12 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1000 Comparator 12MHz 100kHz 6V6V 101MHz 101kHz ΔΦ 3

13. 13 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1000 Comparator 12MHz 100kHz 5.5V 99.5MHz 99.5kHz ΔΦ 4

14. 14 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1000 Comparator 12MHz 100kHz 5.9V 100MHz 100kHz ΔΦ 5

15. 15 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1050 Comparator 12MHz 100kHz 5.9V 100MHz 95.2kHz ΔΦ 5 R=120,N=1050

16. 16 LPF VCO & Buffer 8051 ÷ R=120 ÷ N=1050 Comparator 12MHz 100kHz 8.5V 105MHz 100kHz ΔΦ 6

17. 17 Difficulties

18. 18 Programming Parasitic Capacitance Oscillation Wiring Grounding Connection

19. 19 Grounding is the key parameter for determining the performance of PLL frequency synthesizer. If the grounding is handled inappropriate or not well enough for some critical point, some ac noise signal will be superimposed on the output signal, or modulate output signal with fm signal ruining the phase noise performance.

20. 20

21. 21 Problem Solving

22. 22 To minimize the noise effects, we should place a regular or an ac short circuit capacitor near the critical point, like supply power of chip. The ac fluctuation dual to current drop must be eliminated or at least minimized, we can ac grounding it immediately, making the wire as short as possible to minimize the antenna effect. Bold wire should be used to reduce the resistance, or use one ground plane to reduce the resistance with lesser complexity.

23. 23 The feedback path is as short as possible

24. 24 Regulator place a regular near the supply power of chip.

25. 25 8.8 Grounding for chip place an ac short circuit capacitor near the critical point, like supply power of chip.

26. 26 Use bold wire to reduce the resistance Each component will not influence each other, the fluctuation will not superimposed

27. 27 Achievement

28. 28 Technical Specification Frequency Range88M-108MHz Frequency Error±6KHz Channel Spacing100KHz Output Power-12dB Lock time10ms Operating Voltage20V Operating Current28mA

29. 29

30. 30 Center frequency = 100MHz, Span=100kHz

31. 31 Center frequency = 108MHz, Span=100kHz

32. 32 Center frequency = 108MHz, Span=200kHz

33. 33 4.6 Linearity

34. 34

35. 35

36. 36

37. 37

38. 38 Improvement

39. 39 107MHz Control Voltage 100MHz Control Voltage Transient response of LPF (5/10)x 100 ％ = 50 ％ overshoot 15V 10V

40. 40 50 ％ overshoot 10~20 ％ overshoot By Reducing the feedback gain of LPF