1. CHAPTER 11 PNEUMATICS TRANSMISION
Objectives:
The purpose of this chapter is to describe:
1. Advantages and disadvantages of pneumatic transmission
2. Operation and performance of various pneumatic elements.
3. Operation and performance of some usually used circuits.
Upon completing this chapter, you should be able to:
Be familiar with the main pneumatic components and standardized symbols used for their representation on circuit diagrams.
Explain the operation principle and performance characteristics of some usually used circuits.
Describe the function of each basic component in a practical pneumatic circuit
Design a circuit to perform a desired function.

2. CHAPTER 11 PNEUMATICS TRANSMISION
11.1 Pneumatics Overview
Pneumatic System Structure & Its Operation Principle
In pneumatic system, compressors are used to compress and supply the necessary quantities of air that comes from the atmosphere.
To operate and control these actuators, other pneumatic components are required i.e. air service units to prepare the compressed air and valves to control the pressure, flow and direction of movement of the actuators.

3. Fig.11.1 A Basic Pneumatic System
In production section: ①compressor, ②electric motor, ③pressure switch, ④check valve, ⑤tank, ⑥pressure gauge, ⑦auto drain, ⑧safety valve, ⑨refrigerated air dryer, ⑩line filter
In consumption section: ①air take-off, ②auto drain, ③air service unit, ④directional valve, ⑤actuator, ⑥speed controllers

4. 11.1.2 Pneumatics Properties Table 11.1.Advantages of Pneumatics
Availability
Air is available practically everywhere in unlimited quantities.
Transport
Air can be easily transported in pipelines, even over long distances.
Storage
Compressed air can be stored in a reservoir and removed as required.
Temperature
Compressed air is relatively insensitive to temperature fluctuations.
Explosion proof
Compressed air offers no risk of explosion of fire.
Cleanliness
Unlubricated exhaust air is clean. Any unlubricated air that escapes through leaking pipes or components does not cause contamination.
Components
The operating components are of simple construction and therefore relatively inexpensive.
Speed
Compressed air is a very fast working medium. This enables high working speeds to be attained.
Overload safe
Pneumatic tools and operating components can be loaded to the point of stopping and are therefore overload safe.

5. CHAPTER 11 PNEUMATICS TRANSMISION
Table 11.2.Disdvantages of Pneumatics
Preparation
Compressed air requires good preparation. Dirt and condensate should not be present.
Compression
It is not always possible to achieve uniform and constant piston speeds with compressed air.
Force
requirement
Compressed air is economical only up to a certain force requirement. Under the normal working pressure of 600 to 700 kPa (6 to 7 bar) and dependent on the travel and speed, the output limit is between and N.
Noise level
The exhaust air is loud. This problem has now, however been largely solved due to the development of sound absorption material and silencers.

6. 11.2 Air Generation and Treatment
Fig.11.2 Structure of Air Preparation System

7. 11.2.1.2 Air generation equipments and preparation
Fig.11.4 Two Stage Piston Compressor

8. Fig.11.5 Rotary sliding vane compressor
Air generation equipments and preparation
Fig.11.5 Rotary sliding vane compressor

9. 11.2.1.2 Air generation equipments and preparation
Fig.11.6 Screw Compressor

10. 11.3 Actuators 11.3.1. Linear Cylinder
Fig Construction of a Cylinder

11. Rotary Actuators

12.   Air Motors
Air motors are similar in construction and function to hydraulic motors, and are most commonly of the rotary vane, gear, radial piston, or axial piston type.
They can operate at speeds in excess of 10,000rpm.
Air motors have several advantages that are important in some applications. One advantage is that air motors can stall under full load for indefinite periods of time, another is that they can be used in applications where electric motors would constitute a fire hazard.

13. 11.4 Pneumatic Control Valves
Pressure Control Valves
Fig Safety Valve

14. 11.4.3 Directional Control Valves
Fig Solenoid Valves

15. 11.5 Basic Pneumatic Circuits
Fig Automatic Reciprocate