3. Logical & Physical Topologies A logical technology is how the hosts are connected logically example token Ring can be laid out in a physical star but it is still a logical ring A physical topology is how the hosts are laid out physically in a room or building.

4. Topologies and protocols Most topologies and protocols are linked Token passing protocols must have some form of returning the token back to the start such as a ring Broadcast protocols such as ethernet must not have a ring as this protocol relies on listening to the media as it broadcasts and therefore in a ring would hear itself. So that topology used tends to be a star or point

5. Topologies Bus Ring Star Point-to-point Full-mesh / Partial-mesh

6. Ethernet Topology LAN Topology Half-Duplex must listen to the wire to make sure no one else is sending Media type BNC (British Navel Connector) Speed 10MBps

7. Ethernet This was taken from www.wown.com

8. Ethernet Topology Ethernet Digital, Intel, Xerox (DIX) and 802.3 –Defined the original Ethernet standards –CSMA/CD Carrier Sense Multiple Access with Collision Detection –All versions use a Bus topology –Half-duplex operation (full-duplex capable with the right equipment) Standards –10Base2 – Thin Ethernet – 185m –10Base5 – Thick Ethernet –500m –10BaseT – Twisted-pair Ethernet – 100m The original Ethernet speed was 4-bit data path at 2.5Mhz Current processors are above 2 GHz

9. CSMA/CD Carrier sense - stations sense whether there is traffic on the wire. Wait until medium idle then begin to transmit frame. Multiple access - more than one station can simultaneously be connected and contend for the right to send. Each uses same access algorithm. Collision detection - individual stations detect when there has been a collision (transmissions from two stations interfere with each other) and react appropriately.

10. CSMA/CD Listen to medium during transmission Detect whether another station’s signal interferes Back off from interference and try again

11. Collision Domain This was taken from www.wown.com

12. Ethernet Topology Ethernet technologies 802.3 Standard Ethernet (10Mb) 802.3u Fast Ethernet (100Mb) –Defines a bus topology –Half- or full duplex operation 100Base-TX Cat5/FE UTP – 100 meters 100Base-FX Multi-mode fibre – 400 meters –Maximum raw transmission rate of 100Mb Aggregate rates double when full-duplex 4-bit data path at 25Mhz

13. Ethernet Topology 802.3z Gigabit Ethernet (1000Mb) –Defines a bus topology –Half- or full duplex operation 1000Base-TX Cat5e/Cat6 UTP – 100 meters 1000Base-SX Multi-mode fibre – 260 meters 1000Base-LX Single mode fibre – 10 kilometres –Maximum raw transmission rate of 1Gb Aggregate rates double when full-duplex 8-bit data path at 125Mhz 802.3ae 10Gig Ethernet (10000Mb)

14. Using a switch to separate Collision Domains therefore increasing traffic

15. Ring Topology The Token controller detects that there are no tokens on the network and will generate a Token that is passed in one direction around the loop of computers

16. Ring Topology When a computer has data to send it waits for the Token then attaches its data this goes around the network to the destination required where it is acknowledged and sent back to the originator who then releases the token back on to the network

17. Ring Topology IBM’s token ring was first seen in the late 1970’s Later IEEE 802.5 became the standard Available in 4 Mbps and 16Mbps speed Uses a token to access the network Token is passed around a logical ring of network devices System must acquire the token to transmit data Data always travels around the ring in the same direction, therefore, no collisions

18. FDDI (Fibre Distributed Data Interface) Similar to Token Ring but this carries a redundant ring so that if a station goes down the information is still able to continue B Node Single Attachment System (SAS) A Node Dual Attachment System (DAS)

19. FDDI/CDDI (Copper)

20. Star LAN / WAN Topology Sometimes referred to as Hub & Spoke Active device at the centre of the star

21. Point –to –point WAN Topology Used by switched networks such as X.25 and Frame Relay or Leased line connectivity such as T1

22. Full-Mesh WAN Topology Used by circuit-switched networks such as X.25 and Frame Relay All areas have connectivity between them Must have an interface for each connection and therefore is more expensive but has inbuilt fault tolerance

23. Partial-Mesh WAN Topology Not all areas have connectivity between them Used by circuit- switched networks such as X.25 and Frame Relay

24. Any Questions?