1. 43.35” (LENGTH OF INNER LIQUID HE RESERVIOR)  CONNECTION CHAMBER: FF 4.75”  FF: FLANGE-TO-FLANGE DISTANCE 10.45” TO 12.45” 6.35” TO 8.35” (JACK -2” TO 0) (BOTTOM OF HE COLD FINGER TO A-A FOCAL POINT) COARSE-Z JACK + RNN FF 5.7” TO 7.7” NIPPLE 3.56” 2.47” 50.4” (BETWEEN BOTTOM OF CAGE AND MIDDLE OF CONNECTION CHAMBER) = 42.55” + (7.85” BASED ON SCANNING POSITION AT JACK @ -0.5”)  PROBE/SCANNER HEIGHT 1.42” (36MM SPECIFIED BY INTEMATIX)  BOTTOM PLATE THICKNESS 0.25” ~ 3.33” TO 5.33”  SCANNING POSITION:  Z-STAGE (ATTOCUBE – FULL RANGE 15MM) EXTENSION ~ 0.43” (11MM)  JACK AT -0.5” (THIS DIMENSION DETERMINES HEIGHT OF SPM CAGE – POSSIBLE RANGE -0.2” TO -0.8”)  TRANSFER POSITION:  Z-STAGE ~ 0 =>  JACK NEEDS TO GO DOWN ~1” (@ -1.5”) 10-PIN FEEDTHROUGH FOR SIGNALS (2 FOR TUNNELING CURRENT) HV CABLES (PZT) GO UP THROUGH THE CONNECTION CHAMBER 3.86” LIQUID N 2 CRYO-SHIELD/ANCHOR  COARSE-Z JACK: FF 4.27” TO 6.27” (-2” TO 0)  RNN: DIFFERENTIALLY PUMPED ROTARY PLATFORM – POLAR ROTATION ~ 7.33 TO 8.19” 0.84” FEMALE SMA CONNECTOR  LENGTH OF RF CABLE: 53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)  A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBE THE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37”  LENGTH OF RF CABLE: 53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)  A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBE THE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37” FEMALE SMA CONNECTOR RF CABLE 2.47”

2. 43.35” (LENGTH OF INNER LIQUID HE RESERVIOR)  CONNECTION CHAMBER: FF 4.75”  FF: FLANGE-TO-FLANGE DISTANCE 10.45” TO 12.45” 6.35” TO 8.35” (JACK -2” TO 0) (BOTTOM OF HE COLD FINGER TO A-A FOCAL POINT) COARSE-Z JACK + RNN FF 5.7” TO 7.7” NIPPLE 3.56” 2.47”  PROBE/SCANNER HEIGHT 1.42” (36MM SPECIFIED BY INTEMATIX)  BOTTOM PLATE THICKNESS 0.4” ~ 3.33” TO 5.33”  SCANNING POSITION:  Z-STAGE (ATTOCUBE – FULL RANGE 15MM) EXTENSION ~ 0.39” (10MM)  JACK AT -0.5” (THIS DIMENSION DETERMINES HEIGHT OF SPM CAGE – POSSIBLE RANGE -0.2” TO -0.8”)  TRANSFER POSITION:  Z-STAGE ~ 0 =>  JACK NEEDS TO GO DOWN ~1” (@ -1.5”) 10-PIN FEEDTHROUGH FOR SIGNALS (2 FOR TUNNELING CURRENT) HV CABLES (PZT) GO UP THROUGH THE CONNECTION CHAMBER 3.86” LIQUID N 2 CRYO-SHIELD/ANCHOR  COARSE-Z JACK: FF 4.27” TO 6.27” (-2” TO 0)  RNN: DIFFERENTIALLY PUMPED ROTARY PLATFORM – POLAR ROTATION ~ 7.33 TO 8.19” 0.84” FEMALE SMA CONNECTOR  LENGTH OF RF CABLE: 53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)  A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBE THE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37”  LENGTH OF RF CABLE: 53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)  A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBE THE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37” FEMALE SMA CONNECTOR RF CABLE Updated version 8/23/07 9.67” = (50.55” +2.47”- 43.35”) 50.55” (BASED ON SCANNING POSITION AT JACK @ -0.5”) 5.65” 39.25” ~ 17” TO THE TABLE