Presentation is loading. Please wait.

Presentation is loading. Please wait.

Dept of Electrical Engineering Universiti Tenaga Nasional

Similar presentations


Presentation on theme: "Dept of Electrical Engineering Universiti Tenaga Nasional"— Presentation transcript:

1 Dept of Electrical Engineering Universiti Tenaga Nasional
COMMUNICATION SYSTEM EECB353 Chapter 1 INTRODUCTION TO COMMUNICATION SYSTEMS Dept of Electrical Engineering Universiti Tenaga Nasional

2 Intan Shafinaz Mustafa
INTRODUCTION TO COMMUNICATION SYSTEMS Chapter Outline: 1.1 The Block Diagram of Communication System - Definition - Main Components - Mode of Communication 1.2 SNR, Bandwidth & Rate of Communication 1.3 The Electromagnetic Frequency Spectrum 1.4 Modulation - Continuous-wave Modulation - Pulse Modulation Reference: Frenzel, Chapter 1

3 * 07/16/96 “How do you want to send data/information to someone who is far from you?” People can communicate with other people. This is one unmistakable characteristic that points out the difference between humans and other animals (i.e. the ability to communicate). During the early days, communication among humans was limited by distance. People communicated by natural senses of hearing and sight or by written words. Actual words could be conveyed although the process was very slow. As the distance increased beyond the normal range of vision and hearing it became very difficult or near to impossible to communicate using the above methods. People searched for better ways of communicating faster and over long distances. Smoke signals and flag signaling were used to send messages. These were used for centuries until the nineteenth century when electrical signals came in use. In 1869, the telephone was invented. This marked a real breakthrough. At that time, it seemed like a miracle to be able to talk to someone so many miles away as easily and quickly as they were standing next to you. The arrival of wireless communication nearly three decades after the Telephone, completed the breakthrough it seemed like a miracle to be able to talk to someone so many miles away as easily and quickly as they were standing next to you. *

4 COMMUNICATION OVER LONG DISTANCES IS NO LONGER A PROBLEM.
Communication : To transfer information from one place to another

5 Communication System History
1837 – Samuel Morse invented telegraph. 1858 – First telegraph cable across Atlantic (Canada – Ireland) 1876 – Alexander Graham Bell invented telephone. 1988 – Heinrich Hertz introduce electromagnetic field theory. 1897 – Marconi invented wireless telegraph. 1906 – Radio communication system was invented. 1923 – Television was invented. 1938 – Radar and microwave system was invented for World War II. 1950 – TDM was invented. 1956 – First telephone cable was installed across Atlantic. 1960 – Laser was invented 1962 – Satellite communication 1969 – Internet DARPA 1970 – Corning Glass invented optical fiber. 1975 – Digital telephone was introduced. 1985 – Facsimile machine. 1988 – Installation of fiber optic cable across Pacific and Atlantic. 1990 – World Wide Web and Digital Communication. 1998 – Digital Television. 2003 – Internet Telephony

6 The words "tele", "phon", and "graph" are derived from Greek.
Tele – means ‘at a distance’ Phon – means sound or speech Graph - means writing or drawing Therefore, telecommunication means communication at a distance. This can be done through wires called transmission lines or through atmosphere by a radio link. Other examples include: Telephone – speaking at a distance Television – seeing at a distance Telegraph – writing at a distance

7 Significance of Human Communication
Communication is the process of exchanging information. Main barriers are language and distance. Methods of communication: Face to face Signals Written word (letters) Electrical innovations: Telegraph Telephone Radio Television Internet (computer)

8 Basic Parts of a Communication System
* 07/16/96 “If the information that you want to send is your voice, how to make sure that what you are saying is understood by your friend?” Receiving end Sending end Transmission channel Basic Parts of a Communication System *

9 Intan Shafinaz Mustafa
1.1 The Block Diagram of Communication System Definition - Communication is the transmission of information from a source to a user via some communication link. Figure 1: Com Sys Block Diagram

10 POSSIBLE SCHEMES NUMBER OF POSSIBLE SCHEMES = AAA DAA AAD DAD ADA DDA
COMMUNICATIONS SYSTEM ANALOG DATA OR DIGITAL DATA SOURCE ANALOG DATA OR DIGITAL DATA DESTINATION ANALOG DATA OR DIGITAL DATA NUMBER OF POSSIBLE SCHEMES = A D AAA AAD ADA ADD DAA DAD DDA DDD A D A D A D A D A D A D

11 COMMUNICATIONS SYSTEMS EXAMPLES
DIGITAL MODEM ANALOG MODEM DIGITAL WAN/LAN (DIGITAL) IP GATEWAY IP GATEWAY ANALOG ANALOG

12 COMMUNICATIONS SYSTEMS EXAMPLES
AAAIR FREE SPACE RADIO STATION ANALOG ANALOG ANALOG DS1 ANALOG CODEC CODEC ANALOG

13 1.1 The Block Diagram of Communication System
Main Components of Com Sys: Input message can be: Analog – continuous signal i.e value varies continuously eg. human voice, music, temperature reading Digital – discrete symbol i.e value limit to a finite set eg. data Figure 2: Analog Vs Digital Signal

14 1.1 The Block Diagram of Communication System
Analog Signals An analog signal is a smoothly and continuously varying voltage or current. Examples are: Sine wave Voice Video (TV) Figure : Analog signals (a) Sine wave “tone.” (b) Voice. (c) Video (TV) signal.

15 1.1 The Block Diagram of Communication System
Digital Signals Digital signals change in steps or in discrete increments. Most digital signals use binary or two-state codes. Examples are: Telegraph (Morse code) Continuous wave (CW) code Serial binary code (used in computers)

16 1.1 The Block Diagram of Communication System
Figure: Digital signals (a) Telegraph (Morse code). (b) Continuous-wave (CW) code. (c) Serial binary code.

17 CHAPTER 1 INTRODUCTION TO COMMUNICATION SYSTEMS
* 07/16/96 CHAPTER 1 INTRODUCTION TO COMMUNICATION SYSTEMS WHAT IS BASEBAND ? Electrical Waveform Data (nonelectrical) transmission of a digital or analog signal signaling at its original frequencies. Without any shift in the range of frequencies of the signal The signal is in its original form, not changed by modulation. Baseband is the original information that is to be Sent. *

18 1.1 The Block Diagram of Communication System
(ii) Input Transducer: A device that converts energy from one form to another. Convert an input signal into an electrical waveform. Example: microphone converts human voice into electrical signal referred to as the baseband signal or message signal.

19 Intan Shafinaz Mustafa
1.1 The Block Diagram of Communication System (iii) Transmitter (Tx): Modifies or converts the baseband signal into format appropriate for efficient channel of transmission. Example: If the channel is fiber optic cable, the transmitter converts the baseband signal into light frequency and the transmitted signal is light. Transmitter also use to reformat/reshape the signal so that the channel will not distort is as much. Modulation takes place in the transmitter. It involves static variation of amplitude, phase or frequency of the carrier in accordance to a message signal. Channel fiber ->tx signal = light Channel wired  tx signal = voltage Channel space  tx signal electromagnetic wave

20 1.1 The Block Diagram of Communication System
(iv) Channel: Physical medium through which the transmitter output is sent. Divided into 2 basic groups: Guided Electromagnetic Wave Channel – eg. wire, coaxial cable, optical fiber Electromagnetic Wave Propagation Channel – eg. Wireless broadcast channel, mobile radio channel, satellite etc. Introduces distortion, noise and interference – in the channel, transmitted signal is attenuated and distorted. Signal attenuation increase along with the length of channel. This results in corrupted transmitted signal received by receiver, Rx

21 Transmission Medium (Guided)
Twisted pair Unshielded Twisted Pair (UTP) Shielded Twisted Pair (STP) Coaxial Fiber Optic Waveguide

22 1.1 The Block Diagram of Communication System
(v) Receiver Receiver decodes the received signal back to message signal – i.e it attempts to translate the received signal back into the original message signal sent by the source. Reprocess the signal received from the channel by undoing the signal modification made by transmitter and the channel. Extract the desired signal from the received signal and convert it to a form that suitable for the output transducer. Demodulation takes place in the receiver. (vi) Output transducer Convert electrical signals to its original waveform.

23 1.1 The Block Diagram of Communication System
Transceivers A transceiver is an electronic unit that incorporates circuits that both send and receive signals. Examples are: Telephones Fax machines Handheld CB radios Cell phones Computer modems

24 1.1 The Block Diagram of Communication System
3. Mode of Communication: Broadcasting Involves the use of a single powerful transmitter transmit to many receivers. Demodulation takes place in the receiver. Information-bearing signals flow in one direction Eg. TV and radio (Simplex) ii. Point to point Communication Where a communication process takes place over a link between a single transmitter and a receiver. Information-bearing signals flow in bidirectional, which requires the use of a transmitter and receiver at each end of the link Eg. Telephone (Full Duplex) and walkie talkie (Half Duplex)

25 1.2 SNR, Bandwidth & Rate of Communication
1. Signal to Noise Ratio (SNR): SNR is defined as the ratio of signal power to noise power. Noise distorts the signal and accumulated along the path. The dB value is calculated by taking the log of the ratio of the measured or calculated power (PS) wrt a reference power (PN) level. Commonly referred to as the power ratio form for dB It is normally measured in Decibel (dB), defined as 10 times the algorithm (to base 10) of the power ratio. Eg.: SNR of 10, 100 and 1000 correspond to 10, 20, and 30dBs, respectively. dBm is a dB level using a 1mW reference. Example - Convert 1mW to dBm SNRdB SNR =

26 Decibel decibel is a relative unit of measurement used frequently in electronic communications to describe power gain or loss Equation 1 is commonly referred to as the power ratio form for dB. (Eq. 1) (Eq. 2) (Eq. 3)

27 1.2 SNR, Bandwidth & Rate of Communication
Example 1 – A receiver produces a noise power of 200mW with no signal. The output level increases to 5 W when a signal is applied. Calculate (S + N)/N as a power ratio and in decibels. Example 2 – A measured value of 10mW will result in what dBm power level? Example 3 - A laser diode outputs +10dBm. Convert this value to (i) watts (ii) dB

28 1.2 SNR, Bandwidth & Rate of Communication
Bandwidth is that portion of the electromagnetic spectrum occupied by a signal. Specifically, bandwidth is the difference between the upper and lower frequency limits of the signal or the equipment operation range. Figure 1, shows the bandwidth of the voice frequency range from 300 to 3000Hz. The upper frequency is f2 and the lower frequency is f1. The bandwidth, then is BW = f2 – f1 Bandwidth is the frequency range over which equipment operates or that portion of the spectrum occupied by the signal. This is the voice frequency bandwidth.

29 Chapter 1 Introduction to Communication Systems
* 07/16/96 Chapter 1 Introduction to Communication Systems WHAT IS BANDWIDTH ? IT IS THE DIFFERENCE BETWEEN THE HIGHEST FREQUENCIES AND THE LOWEST FREQUENCIES OF THE INPUT SIGNAL FREQUENCIES (fB = 2fm ). The bandwidth of a communication signal  bandwidth of the information signal. In electronic communication, bandwidth is the width of the range (or band) of frequencies that an electronic signal uses on a given transmission medium. In this usage, bandwidth is expressed in terms of the difference between the highest-frequency signal component and the lowest-frequency signal component. What is bandwidth? Bandwidth is the total range of frequency required to pass a specific signal that has been modulated to carry data without distortion or loss of data. The ideal bandwidth allows the signal to pass under conditions of maximum AM or FM adjustment. (Too narrow a bandwidth will result in loss of data. Too wide a bandwidth will pass excessive noise.) Transmitters and receivers have bandwidths. The "wider" the receiver's bandwidth is, the more information it can receive on different frequencies. The term bandwidth is used metaphorically for the carrying ability of Internet carriers. For example, if you can receive information from the Internet over a slow modem, you get less information per second than if you were connected to a fast modem. Thus, you have "low bandwidth" and the Internet appears slower to you. Modem (from modulator-demodulator) is a device that modulates an analog carrier signal to encode digital information, and also demodulates such a carrier signal to decode the transmitted information. The goal is to produce a signal that can be transmitted easily and decoded to reproduce the original digital data. Modems can be used over any means of transmitting analog signals, from driven diodes to radio. *

30 1.2 SNR, Bandwidth & Rate of Communication
Bandwidth of a channel is the range of frequencies that it can transmit with reasonable fidelity. Bandwidth of an information signal is the difference between the highest and lowest frequencies contained in the information. Bandwidth of a communication channel is the difference between the highest and lowest frequencies that the channel will allow to pass through it (ie: its pass band). Data rate proportional to bandwidth

31 1.2 SNR, Bandwidth & Rate of Communication
Rate of information transmission is directly proportional with its bandwidth Shannon limit for information capacity, C C = B log2 (1 + SNR) = 3.32B log10 (1 + SNR) Where C = information capacity (bps) B = bandwidth (Hz) SNR = signal to noise ratio (no unit)

32 1.2 SNR, Bandwidth & Rate of Communication
Example 4 -The telephone channel has a bandwidth of about 3kHz. Calculate the capacity of a telephone channel that has an SNR of 1023. Example 5 – For a standard telephone circuit with a SNR of 30dB and a bandwidth of 2.7 kHz, determine the Shannon limit for information capacity.

33 1.3 The Electromagnetic Spectrum
Electromagnetic waves are signals that oscillate; i.e the amplitudes of the electric and magnetic fields vary at a specific rate. These oscillation may occur at a very low frequency or at an extremely high frequency. The range of electromagnetic signals encompassing all frequencies is referred to as the electromagnetic spectrum.

34 1.3 Electromagnetic Frequency Spectrum
Definition of the Electromagnetic Spectrum The total span of frequencies and corresponding wavelength used in communications systems.

35 1.3 Electromagnetic Frequency Spectrum
Frequency and Wavelength: Frequency A signal is located on the frequency spectrum according to its frequency and wavelength. Frequency is the number of cycles of a repetitive wave that occur in a given period of time. A cycle consists of two voltage polarity reversals, current reversals, or electromagnetic field oscillations. Frequency is measured in cycles per second (cps). The unit of frequency is the hertz (Hz).

36 1.3 Electromagnetic Frequency Spectrum
Frequency and Wavelength: Wavelength Wavelength is the distance occupied by one cycle of a wave and is usually expressed in meters. Wavelength is also the distance traveled by an electromagnetic wave during the time of one cycle. The wavelength of a signal is represented by the Greek letter lambda (λ).

37 1.3 Electromagnetic Frequency Spectrum
Figure : Frequency and wavelength. (a) One cycle. (b) One wavelength.

38 1.3 Electromagnetic Frequency Spectrum
Frequency and Wavelength: Wavelength Wavelength (λ) = speed of light ÷ frequency Speed of light = 3 × 108 meters/second Therefore: λ = 3 × 108 / f Example: What is the wavelength if the frequency is 4MHz? λ = 3 × 108 / 4 MHz = 75 meters (m)

39 1.3 Electromagnetic Frequency Spectrum
Example 6 A signal with a wavelength of 1.5m , what is its frequency? Example 7 A signal travels a distance of 75ft in the time it takes to complete 1 cycle. What is its frequency? (Given 1m = 3.28ft) Example 8 The maximum peaks of an electromagentic wave are separated by a distance of 0.203m. What is the frequency in MHz and GHz?

40 1.3 Electromagnetic Frequency Spectrum
The purpose of an electronic communications system is to communicate information between two or more locations/stations. This is accomplished by converting the original information into electromagnetic energy and then transmitting it to one or more received stations where it converted back to its original form. Electromagnetic energy can propagate as a voltage or current along a metallic wire, as emitted radio waves through free space or as light waves down an optical fiber. Electromagnetic energy is distributed throughout an almost infinite range of frequencies.

41 1.3 Electromagnetic Frequency Spectrum
Antenna & Propagation Electromagnetic waves consists of electric field (E) & magnetic field (H) Polarization is determined by the E-field, and thus same with antenna’s physical configuration Polarization – the field of the electric field of an electromagnetic wave

42 1.3 Electromagnetic Frequency Spectrum
Types of radio wave propagation Ground Wave (Surface Wave) Radio wave that travels along the earth’s surface. The propagation is better over water, esp salt water. Not effective for freq above 2MHz Reception not affected by daily or seasonal changes. Application: submarine application

43 1.3 Electromagnetic Frequency Spectrum
Space Wave Divided into 2 types direct wave & ground reflected wave Limited by line of sight (LOS) Antenna height and earth curvature become important factors

44 1.3 Electromagnetic Frequency Spectrum
Sky Wave Radiated from the transmitting antenna in direction toward the ionosphere. Skipping the alternate refracting and reflecting of a sky wave signal between the ionosphere and earth’s surface. The ability of the ionosphere to return the radio wave depends on the ion density, frequency of radio wave and angle of transmission.

45 1.3 Electromagnetic Frequency Spectrum
Antennas Half Wave Antenna: The physical length is 1/2 wavelength of the applied frequency. Typically used for >2 MHz Dipole Antenna Straight radiator, typically ½ wavelength long, usually separated at center by insulator and fed by a balanced transmission line.

46 1.3 Electromagnetic Frequency Spectrum
Antennas Radiation Pattern diagram indicating the intensity of radiation as a function of direction Omnidirectional a spherical radiation pattern Directional concentrating antenna energy in certain directions at the expense lower energy in other directions Beamwidth Angular separation between the half power points on an antenna’s radiation pattern Antenna gain How much more power in dB an antenna will radiate in a certain direction with respect to the reference antenna (isotropic point source or dipole)

47 Monopole Antenna Typically used for <2 MHz
Large amount of energy is launched as a ground wave

48 Yagi-Uda Antenna

49 Driven Collinear Array

50 1.4 Modulation Modulation is the process of putting information onto a high frequency carrier in a transmitter. Modulation is important because: Ease of radiation - related to antenna design & smaller size. Low loss and low dispersion. Simultaneous transmission of several signals – enables the multiplexing i.e combining multiple signals for tx at the same time over the same carrier. Classification of modulation process: Analog modulation- consists of Continuous Wave (CW) modulation and pulse modulation Digital Modulation- ASK, PSK, FSK

51 Continuous Wave (CW) Modulation
CW modulation means that some characteristic of a sinusoidal carrier is varied in accordance with the message (modulating) signal. In CW modulation, the modulated carrier is normally sinusoidal signal of the form Where V, fc and θ are the instantaneous amplitude, frequency and angle respectively, of the carrier. Varied characteristics: Amplitude – Amplitude Modulation (AM) Frequency – Frequency Modulation (FM) Phase – Phase Modulation (PM)

52 Chapter 1 Introduction to Communication Systems
WHAT IS MODULATION ? MODULATION IS THE PROCESS OF CHANGING SOME PROPERTYOF THE INFORMATION SOURCES/SIGNAL INTO SUITABLE FORM FOR TRANSMISSION THROUGH THE PHYSICAL MEDIUM/CHANNEL It is performed in the Transmitter by a device called Modulator. 52

53 Chapter 1 Introduction to Communication Systems
WHAT IS DEMODULATION ? DEMODULATION IS THE REVERSE PROCESS OF MODULATION BY CONVERTING THE MODULATED INFORMATION SOURCES/SIGNAL BACK TO ITS ORIGINAL INFORMATION (IT REMOVES THE INFORMATION FROM THE CARRIER SIGNAL). It is performed in the Receiver by a device called Demodulator. 53

54 THE NEED OF MODULATION Channel assignment (various information sources are not always suitable for direct transmission over a given channel) Reduce noise & interference Overcome equipment limitation 54

55 Amplitude Modulation (AM) Frequency Modulation (FM)
* 07/16/96 TYPE OF MODULATION Amplitude Modulation (AM) Frequency Modulation (FM) Phase Modulation (PM) Phase modulation (PM) is a form of modulation that represents information as variations in the instantaneous phase of a carrier wave. Unlike its more popular counterpart, frequency modulation (FM), PM is not very widely used. This is because it tends to require more complex receiving hardware and there can be ambiguity problems with determining whether, for example, the signal has 0° phase or 180° phase. 55 *

56 TYPE OF MODULATION 56

57 Modulation Signal Carrier Wave Modulated Signal Demodulation
AMPLITUDE MODULATION

58

59 1.5 Multiplexing & Demultiplexing
Intan Shafinaz Mustafa 1.5 Multiplexing & Demultiplexing Multiplexing is a process of combining several signals for simultaneous transmission over same channel. Demultiplexing is a process of extracting individual signal from a combined signal. There are 4 types of multiplexing: Frequency Division Multiplexing (FDM) Time Division Multiplexing (TDM) Code Division Multiplexing (CDM) Wavelength Division Multiplexing (WDM)

60 Intan Shafinaz Mustafa
REVIEW QUESTIONS 1. Define Communication Systems. [1m]  2. Define Bandwidth of a channel. [1m]  3.A laser diode outputs +20dBm. Convert this value to: [2m]  a) Watt b) dB 4. A communications link is using a transmitter of 15W power and there is 1W of noise in the same link. The available bandwidth is 3 kHz. Determine the Shannon limit for information capacity.[2m]


Download ppt "Dept of Electrical Engineering Universiti Tenaga Nasional"

Similar presentations


Ads by Google