Presentation is loading. Please wait.

Presentation is loading. Please wait.

Verigy V93000 Service Training

Similar presentations


Presentation on theme: "Verigy V93000 Service Training"— Presentation transcript:

1 Verigy V93000 Service Training
Module 17: V93000 Digital Cards Module 17: PinScale Cards Objective: Given: Service Guide II Study Guide Quiz Answer questions about the V93000 PinScale digital I/O channel cards. 90% correct answers are required to get credit for this module. Reference: Service Guide II Chapter 4, “Test Head”

2 Channel Cards Back plane address, data, control bus interface and DIS Interface. Up to 8 digital cards can be installed in each card cage. Up to 16 digital cards in CTH Up to 32 digital cards in STH Up to 64 digital cards in LTH Each digital card holds: 1x Interface Module 1x Relay or FORM Module 8x Channel modules Each PS400 card has 64 I/O channels Each PS800/PS3600/HSM card has 32 I/O channels Supply voltages from DC/DC Power Unit, MCLK from Clock boards, and direct connection to the DPS Pogo Pins. 17 - PinScale Cards

3 PS400 Channel Board to DUT Interface
Front Plane DUT Side Card cage Side A B Board A C The DUT Interface holds the DUT board in place. The signal path between the DUT and the pin electronics is established through pogo pins and coax cables. D Board B (backside) Board C Board D (backside) 17 - PinScale Cards

4 PS800/PS3600 Channel Board to DUT Interface
Board 1, Ch. 1-16 DUT Side Front Plane Board 2, Ch. 1-16 Card Cage Side The DUT Interface holds the DUT board in place. The signal path between the DUT and the pin electronics is established through pogo pins and coax cables. Brd 1 Brd 2 17 - PinScale Cards

5 Channel Card Syntax Verigy is using a 5 digit number to identify a channel Ch 10815 Channel 15 on specific logical I/O board -number range Logical Pogo Block 108 on the DUT Interface -number range in Small TH or Compact TH with PS400 card and and -number range in Large TH or Small TH with DUT Scale interface and and -number range in Compact TH and Note: To locate a logical I/O board location, one must use the pogo mapping file to cross reference the logical pogo block location to the card slot location. 17 - PinScale Cards

6 Model File GLOBAL testhead = TH_8CC # TH_2CC | TH_4CC | TH_8CC dut_interface = SOC # F330 | SOC | EXHIBITION hpib_interface = vxi11/ /gpib0 # hpib | vxi11/ /gpib0 timing_bundle = w256-d8-r8 # gigamem = 5 # xpressdata = ON # multisite = ON IOCHANNEL # Pin Scale System Unified Memory Mode # :HW = PS800, speed = 800 Mbps, smem = 64M, diff, ppTIA # :HW = PS3600, speed = 3600 Mbps, smem = 64M, diff, ppTIA # :HW = PS400, speed = 400 Mbps, smem = 56M, ppTIA # Pin Scale System Compatible Memory Mode # :HW = PS800, speed = 800 Mbps, smem = 2M, vmem = 54M, diff, ppTIA # :HW = PS3600, speed = 3600 Mbps, smem = 2M, vmem = 54M, diff, ppTIA # :HW = PS400, speed = 400 Mbps, smem = 2M, vmem = 47M, ppTIA ANALOGBOARD # ... (recommended if no backward compatibility with SD is needed) (for backward compatibility with SD testers) 17 - PinScale Cards

7 PS400 Channel Assignment Channel assignment is printed on metal cover
One logical board consists of 16 channels, located on two channel modules Each logical board is connected to 1 pogo block Logical Logical Board C Board A Logical Logical Board B Board D The positions of the individual channel modules are printed on the metal cover of the digital card. Note that the card is divided into two logical boards, where each supports one pogo block with 16 channels. Logical board 1 will always be an odd channel board. (i.e , …) Logical board 2 will always be an even channel board. (i.e. 102, 104, …) 17 - PinScale Cards

8 PS800/PS3600 Channel Assignment
Logical Logical Board 1 Board 2 Logical Logical Board 2 Board 1 Channel assignment is printed on metal cover Example: If the card location is 1st digital card slot in group1,  Logical board 1 connects to 101 pogo block.  Logical board 2 connects to 102 pogo block. The positions of the individual channel modules are printed on the metal cover of the digital card. Note that the card is divided into two logical boards, where each supports one pogo block with 16 channels. Logical board 1 will always be an odd channel board. (i.e , …) Logical board 2 will always be an even channel board. (i.e. 102, 104, …) 17 - PinScale Cards

9 PS400 Pogo Cable Identifying the installation location:
Label “A” for 101, 105, ) Label “B” for 102, 106, ) Label “C” for 103, 107, ) Label “D” for 104, 108, ) C B A Pin Scale 400 Pogo Cable E 17 - PinScale Cards

10 PS800/PS3600 Pogo Cables Identifying the installation location:
Pin Scale 800 Pogo Cable: E7945P (Replacement part: E ) A B Identifying the installation location: Label “A” for odd-numbered logical boards. (101, 103, ) Label “B” for even-numbered logical boards. (102, 104, ) A Pogo Cable: E8010P for other cards (Replacement part: E ) B 17 - PinScale Cards

11 Pogo Cable Filling Legacy compatible Filling for Pin Scale/HSM systems
Up to 384 pins (4CC) / 768 pins (8CC) Filling for Pin Scale/HSM systems More than 384 pins (4CC) / 768 pins (8CC) Each Pin Scale/HSM pogo cable has two pogo connectors 17 - PinScale Cards

12 Pogo Pin Assignment Orientation Marker 01 02 a b c 01 a b 03 a b c 02
: 17 Orientation Marker a b 01 02 03 : 17 Orientation Marker a b c a b c 17 - PinScale Cards

13 PS400 Overview Interface Module x 1 8-Channel Module x 8
Backplane I/F DCLK Distribution 8-Channel Module x 8 Test Processor Memory Pin PMU AC/PPMU Switch DCL (Driver-Receiver IC for Drv/Cmp/Load) Relay Module x 1 64 DC Relays 9 Central Relays MCLK Distribution Frontplane I/F 4 x Board ADC Product Number: E8012A: Pin Scale 400 Card E8012P: Pogo Assembly Function Summary: 64 x digital I/O 400Mbps data rate up to 56 MV per channel 64 x PPMU 4 x Board ADC 17 - PinScale Cards

14 PS800 Overview Product Number: E7945A: Pin Scale 800 Card
Interface Module x 1 Backplane I/F DCLK Distribution 2 x Board ADC 4-Channel Module x 8 Test Processor Memory Pin PMU DRIC (Driver-Receiver IC for Drv/Cmp/Load) Relay Module x 1 AC/DC/PPMU Relay Central Relay MCLK Distribution Frontplane I/F Product Number: E7945A: Pin Scale 800 Card E7945P: Pogo Assembly Function Summary: 32 x digital I/O 800Mbps data rate 54MV per channel 2M sequencer memory 32 x PinPMU 2 x Board ADC DRIC stands for Driver-Receiver IC. You may also find DCL (Driver, Comparator and active Load) in some documents. 17 - PinScale Cards

15 PS3600/HSM Digital Card Overview
Interface Module x 1 Backplane I/F DCLK Distribution 2 x Board ADC 4-Channel Module x 8 Test Processor Memory Pin PMU DRIC (Driver-Receiver IC for Drv/Cmp/Load) AC/DC/PPMU Relay Relay (Form) Module x 1 Central Relay MCLK Distribution Frontplane I/F Product Number: E8010A: Pin Scale 3600 Card E8610A/E8620A: HSM Cards E8010P: Pogo Assembly Function Summary: 32 x digital I/O 3600Mbps data rate 54MV per channel 2M sequencer memory 32 x PinPMU 2 x Board ADC Board-cable Assembly x 1 DRIC stands for Driver-Receiver IC. You may also find DCL (Driver, Comparator and active Load) in some documents. 17 - PinScale Cards

16 PS400 Functional Block Diagram
Data/Clock Control Interface Module 8 x 8-Channel Module Relay Module Clock: Module 2, Data: Module 3 FPGA FPGA with Interface State Machine Clock: Module 7, Data: Module 6 HPPMU I/F 4 x Board ADC Diag MUX Frontplane Interface 8-Channel Module Pin PMU AC/PPMU Switch x 8 Backplane Interface MCLK Distribution Clock Distribution DC/Central Relay DUT Interface The block diagram of the Pin Scale 800 card is almost identical to that of P and Ce. Two EPLD make up the Interface State Machine and the Data Path. 17 - PinScale Cards

17 To Board ADC & I/F State Machine
PS800 - Functional Block Diagram Data/Clock Control Interface Module 8 x 4-Channel Module Relay Module 2 x Board ADC HPPMU I/F Board ADC MUX Diag MUX To Board ADC & I/F State Machine Data Path Frontplane Interface 4-Channel Module Pin PMU x 8 MCLK Distribution Interface State Machine Backplane Interface DUT Interface Clock Distribution AC/DC/PMU/Central Relay The block diagram of the Pin Scale 800 card is almost identical to that of P and Ce. Two EPLD make up the Interface State Machine and the Data Path. 17 - PinScale Cards

18 To Board ADC & I/F State Machine
PS3600/HSM - Functional Block Diagram Relay Module 8 x 4-Channel Module Interface Module Interface State Machine Data Path 2 x Board ADC HPPMU I/F Board ADC MUX Diag MUX Frontplane Interface MCLK Distribution DUT Interface Clock Backplane Interface Data/Clock Control To Board ADC & I/F State Machine 4-Channel Module Pin PMU AC/DC/PPMU Rly x 8 Central Relay (Board-signal cable) The block diagram of the Pin Scale 3600 card is almost identical to that of P and Ce. One FPGA makes up the Interface State Machine and the Data Path. The DUT interface connects to the channel module directly via the board-signal cable (for high speed signal handling). 17 - PinScale Cards

19 PS400 Power Routing Interface Module 8 x 8 -Channel Module
Control 5 V -12 V Interface Module – 6 V (Modules 1,3,8) 8 x 8 -Channel Module Relay Module – 6 V (5 modules) Voltage Regulator DCL 10 V -10V,12 V LevGen PMU IC Voltage Regulator Noise Filter 20V 2.5V 14 V 6.5 V 3.3 V – 12 V DDR2 12 V DC/DC 1.8 V DC/DC 2.5V DC/DC 6.5V 2.5 V Test Processor Backplane Frontplane DC/DC 1.2 V 1.2V DC/DC 6.5V NOTE: Monitored temperature uses temp sensor on Interface module. DC/DC Control Over Current/Voltage Control Interface State Machine Power Ctrl Bd Temp. Control Board Temp. Power from the DC/DC Boards is routed via the frontplane and the backplane to DC/DC converters located on the interface module and the relay module. After the DC/DC power units are powered up, the control board releases the n_power_ok signal. This starts the part of the interface state machine that powers up the DC/DC converters in the following defined order: a) 1.8V Test processor digital and analog b) 2.5V RDRAM power c) 1.8V RDRAM termination d) 3.3V Test processor I/O In case of a DC/DC board failure, there are over current, over voltage and over temperature sensors to protect the HW. If a failure is reported to the interface state machine, the DC/DC converters are powered down in the reverse order. An alarm is reported to the power control board, which starts an emergency shutdown of the whole system. Use the Low Level Diagnostic Tests DPCI and DPCE to troubleshoot. There are 5 LEDs for monitoring the power and interface status. See I/F module slides for details. The Board ADC is powered by the clock board. 17 - PinScale Cards

20 PS800 – Power Routing Interface Module 8 x 4-Channel Module
Control Interface Module 8 x 4-Channel Module Relay Module DRIC 5 V 12 V Voltage Regulator – 6 V 10 V 14 V 8 V 6.5 V – 12 V Voltage Regulator Noise Filter 12 V 2.5 V DC/DC RDRAM Termination 12 V 1.8 V DC/DC 1.8 V DC/DC Test Processor I/O 1.8 V DC/DC 5 V 3.3 V Backplane DC/DC Frontplane NOTE: Monitored temperature uses temp sensor on Interface module. DC/DC Control Over Current/Voltage Control Interface State Machine Power Ctrl Bd Temp. Control Board Temp. Power from the DC/DC Boards is routed via the frontplane and the backplane to DC/DC converters located on the interface module and the relay module. After the DC/DC power units are powered up, the control board releases the n_power_ok signal. This starts the part of the interface state machine that powers up the DC/DC converters in the following defined order: a) 1.8V Test processor digital and analog b) 2.5V RDRAM power c) 1.8V RDRAM termination d) 3.3V Test processor I/O In case of a DC/DC board failure, there are over current, over voltage and over temperature sensors to protect the HW. If a failure is reported to the interface state machine, the DC/DC converters are powered down in the reverse order. An alarm is reported to the power control board, which starts an emergency shutdown of the whole system. Use the Low Level Diagnostic Tests DPCI and DPCE to troubleshoot. There are 5 LEDs for monitoring the power and interface status. See I/F module slides for details. The Board ADC is powered by the clock board. 17 - PinScale Cards

21 PS3600/HSM – Power Routing DC/DC Interface Module 8 x 4-Channel Module
Control Interface Module 8 x 4-Channel Module Relay Module DRIC – 6 V (6 modules) – 6 V (2 modules) 5 V 12 V Voltage Regulator Voltage Regulator Noise Filter 14 V 8 V 6.5 V – 12 V 8 V 12 V 2.5 V DC/DC RDRAM Termination 12 V 1.8 V DC/DC 1.8 V DC/DC Test Processor I/O 1.8 V DC/DC 5 V 3.3 V Backplane DC/DC Frontplane NOTE: Monitored temperature uses temp sensor on Interface module. DC/DC Control Over Current/Voltage Control Interface State Machine Power Ctrl Bd Temp. Control Board Temp. Temp. Power from the DC/DC Boards is routed via the frontplane and the backplane to DC/DC converters located on the interface module and the relay module. After the DC/DC power units are powered up, the control board releases the n_power_ok signal. This starts the part of the interface state machine that powers up the DC/DC converters in the following defined order: a) 1.8V Test processor digital and analog b) 2.5V RDRAM power c) 1.8V RDRAM termination d) 3.3V Test processor I/O In case of a DC/DC board failure, there are over current, over voltage and over temperature sensors to protect the HW. If a failure is reported to the interface state machine, the DC/DC converters are powered down in the reverse order. An alarm is reported to the power control board, which starts an emergency shutdown of the whole system. Use the Low Level Diagnostic Tests DPCI and DPCE to troubleshoot. There are 5 LEDs for monitoring the power and interface status. See I/F module slides for details. The Board ADC is powered by the clock board. 17 - PinScale Cards

22 PS400 Components and Function
Cover Side Connector Side Test Processor Sequencer Edge Generator Data Formatter Data Comparator Error Map Generator DAC for Level Generator and Active Load DDR2 Memory 56 MV/channel 3 GV/card for scan Level Gen - PMU IC Reference V/I generator Pin PMU AC and PPMU Switch DCL Driver Comparator Active load Level Generator Generates reference voltages and currents that are fed into the Pin PMU and the driver-receiver IC. These levels are needed to define the correct voltage levels on the outputs of these chips. Driver Receiver IC (including the active load functionality) The DRIC receives instructions and data from the test processor. Based on the control signals received, the DRIC creates the action to be performed. The function of a pogo pin can be a: Driver Receiver/comparator, with the following modes: Single ended, dual-level as in Single Density Differential (between 2 pins) Tristate port Active load, using two of the currents generated by the test processor. 17 - PinScale Cards

23 PS800 Components and Function
Cover Side Connector Side RDRAM 54MV/channel 1728MV/board for scan 2M sequence/channel Test Processor Sequencer Edge Generator Data Formatter Data Comparator Error Map Generator DAC for Level Generator and Active Load Level Generator Reference V/I generator Driver-Receiver IC Driver Comparator (Dual-Level and Differential) Active load Pin PMU Level Generator Generates reference voltages and currents that are fed into the Pin PMU and the driver-receiver IC. These levels are needed to define the correct voltage levels on the outputs of these chips. Driver Receiver IC (including the active load functionality) The DRIC receives instructions and data from the test processor. Based on the control signals received, the DRIC creates the action to be performed. The function of a pogo pin can be a: Driver Receiver/comparator, with the following modes: Single ended, dual-level as in Single Density Differential (between 2 pins) Tristate port Active load, using two of the currents generated by the test processor. 17 - PinScale Cards

24 PS3600/HSM Components and Function
Cover Side Connector Side Test Processor Sequencer Edge Generator Data Formatter Data Comparator Error Map Generator DAC for Level Generator and Active Load RDRAM 54MV/channel 1728MV/board for scan 2M sequence/channel Driver-Receiver IC Driver (Standard, Fast) Comparator (Dual-Level, High Speed, Differential) Active load Level Generator Reference V/I generator Board-cable Connector AC Relay (50) Inductor Pin PMU DC/PPMU Relay Level Generator Generates reference voltages and currents that are fed into the Pin PMU and the driver-receiver IC. These levels are needed to define the correct voltage levels on the outputs of these chips. Driver Receiver (Active Load) The DRIC receives instructions and data from the test processor. Based on the control signals received, the DRIC creates the action to be performed. The function of a pogo pin can be a: Driver in Standard Mode (Single Density compatible) and in Fast Mode Receiver/comparator, with the following modes: Single ended, dual-level (Standard Mode as in Single Density) Single ended, high speed (Fast Mode) Differential between 2 pins (Standard and Fast Mode) Tristate port Active load, using two of the currents generated by the test processor. Inductor The inductor has high impedance for AC signals, but low impedance for DC as needed for measurements and calibration via the DC and the PPMU relay. 17 - PinScale Cards

25 PS400 Interface Module Components
Backplane Transceivers Configuration Controller (CPLD) DC/DC Converters Temperature Sensor DCLK Distribution (for data flow synchronization) Backplane Transceivers Interface Module FPGA Flash Memory for FPGA configurations Status Indicator LED (7x Green LED & 3x Red LED) Backplane Interface (mainly BTL) The driver and receiver of address/data bus. Data Path The data path is used for downloading test vectors and sequencer instructions and for uploading the test result to the control board. Interface State Machine Controls the Interface module function, DC/DCs and the information flow between the channel module and the control board. DCLK Clock Distribution Distribution of DCLK (20MHz), generated on the Control board, to the Channel module interface (Data flow synchronization) Board ADC Basically consists of two 16 bit ADCs and analog multiplexers. 17 - PinScale Cards

26 PS800 Interface Module Components
Backplane Drivers (Backplane Transceiver Logic) BTL exists both side of the module Temperature Sensor DC/DC Converter DCLK Distribution (for data flow synchronization) Distribute DCLK (20MHz) from control board to channel module. Interface State Machine (2xEPLD) Controller for interfacing and information flow between channel module and control board. 2 x Board ADC (2x 16bit ADC + Analog MUX) For PPMU Monitor, Cal/diag measurement. Powered by 12V/±5V from clock board. Status Indicator LED (2x Green LED & 1x Red LED) fiber-link/power failure Backplane Interface (mainly BTL) The driver and receiver of address/data bus. Data Path The data path is used for downloading test vectors and sequencer instructions and for uploading the test result to the control board. Interface State Machine Controls the Interface module function, DC/DCs and the information flow between the channel module and the control board. DCLK Clock Distribution Distribution of DCLK (20MHz), generated on the Control board, to the Channel module interface (Data flow synchronization) Board ADC Basically consists of two 16 bit ADCs and analog multiplexers. 17 - PinScale Cards

27 PS3600/HSM Interface Module Components
Backplane Drivers (Backplane Transceiver Logic) BTL exists both side of the module Temperature Sensor DC/DC Converter DCLK Distribution (for data flow synchronization) Distribute DCLK (20MHz) from control board to channel module. Interface State Machine (EPLD) Controller for interfacing and information flow between channel module and control board. 2 x Board ADC (2x 16bit ADC + Analog MUX) For PPMU Monitor, Cal/diag measurement. Powered by 12V/±5V from clock board. Status Indicator LED (3x Green LED & 1x Red LED) fiber-link/power failure Backplane Interface (mainly BTL) The driver and receiver of address/data bus. Data Path The data path is used for downloading test vectors and sequencer instructions and for uploading the test result to the control board Interface State Machine Controls the Interface module function, DC/DCs and the information flow between the channel module and the control board. DCLK Clock Distribution Distribution of DCLK (20MHz), generated on the Control board, to the Channel module interface (Data flow synchronization) Board ADC Basically consists of two 16 bit ADCs and analog multiplexers. 17 - PinScale Cards

28 Interface Module Power Status LEDs
PS400 Fiber Link and Power Status Information 1) RDY Fiber link connection and power status OK 2) FLT/ALM Fiber link not connected or power failure FPGA Status Information (per FPGA) 3) ERR FPGA configuration error 4) LOAD Configuration of FPGA in progress 5) SAFE Factory FPGA configuration loaded 6) USER FPGA configuration completed Relay Module FPGA Interface Module FPGA Additional information for troubleshooting: 1) Red Should be off if power and fiber link is OK 2) Green Should be on if fiber link connection and power status OK 3) Orange Should be usually off 4) Yellow Should flash only during data transfer 5) Green Should be off after power on 17 - PinScale Cards

29 Interface Module Power Status LED’s
PS PS3600/HSM 1) Red Fiber link is not connected or power failure 2) Green Fiber link connection and power status OK 3) Orange Test register (for internal use) 4) Yellow Data Handshake data transfer) 1) Red Fiber link is not connected or power failure 2) Green Fiber link connection and power status OK 3) Orange Test register (for internal use) 4) Yellow Data Handshake data transfer) 5) Green Configuration of FPGA in progress Additional information for troubleshooting: 1) Red Should be off if power and fiber link is OK 2) Green Should be on if fiber link connection and power status OK 3) Orange Should be usually off 4) Yellow Should flash only during data transfer 5) Green Should be off after power on 17 - PinScale Cards

30 PS400 Board ADC Four 16-bit ADCs on the relay module for the purposes of: PPMU value measurement Diagnostic (temperature, supply voltages) Calibration The Board ADCs are powered by 12V/± 5V from the Clock Board Logical Board A Channel 1 : Channel 16 Board ADC A Mux Logical Board B Channel 1 : Channel 16 Board ADC B Mux Logical Board C Channel 1 : Channel 16 Board ADC C Mux Logical Board D Board ADC D Channel 1 : Channel 16 Mux Result Interface Module Channel Module Relay Module This slide shows the path from the monitor output of the Pin PMU to the Board ADCs on the interface module. Signal traces from Analog MUX to Board ADC: Pin Scale 800: Channel module for logical Board 2, channel 01-04 Pin Scale 3600: Channel module for logical Board 1, channel 05-08 This is helpful troubleshooting information if PMU value measurement fails. 17 - PinScale Cards

31 PS800/PS3600 Board ADC Two 16-bit ADCs on the interface module for the purposes of: PPMU value measurement Diagnostic (temperature, supply voltages) Calibration Board ADC is powered by 12V/± 5V from the Clock Board Result Channel 1 : Channel 16 Board ADC A Interface Module Channel Relay Logical Board 1 Board ADC B Logical Board 2 Analog MUX NOTE: Signal traces from Analog MUX to Board ADC: Pin Scale 800: Channel module for logical Board 2, channel 01-04 Pin Scale 3600/HSM: Channel module for logical Board 1, channel 05-08 This is helpful troubleshooting information if PMU value measurement fails. This slide shows the path from the monitor output of the Pin PMU to the Board ADCs on the interface module. Signal traces from Analog MUX to Board ADC: Pin Scale 800: Channel module for logical Board 2, channel 01-04 Pin Scale 3600: Channel module for logical Board 1, channel 05-08 This is helpful troubleshooting information if PMU value measurement fails. 17 - PinScale Cards

32 PS400 Relay Module Components
Analog Multiplexer PPMU monitor/Diagnostics/Calibration signals to board ADC Relay Drivers 4 Board ADCs Relay Module FPGA MCLK Distribution Temperature Sensor Linear Regulators, DC/DC Converters DC Relays One channel connects to each relay Central Relays 9 relays for DC rail/GND-sense/Board ADC path MCLK distribution detail: Differential ECL Signals (2 pairs per channel module) Impedance controlled, 50 Ohm terminations Reference Level: Vcc = 3.3V (Compatible with Test processor CMOS Inputs) The Relay Module provides access to the frontplane. In detail, it contains the following circuitry: Frontplane interface Diagnostic interface (Analog Multiplexers) MCLK distribution 3 Relays for each channel: AC Relay 50, 6 pins DC Relay, 4 pins PMU Relay, 4 pins 8 Central Relays for DC-rail, GND-sense and Board ADCs Temperature measurement circuit/sensor 17 - PinScale Cards

33 PS800 Relay Module Components
Temperature Sensor Linear Regulators, DC/DC Converter AC(50)/PMU/DC Relay One channel connects to each relay Central Relay 8 relays for DC rail/GND-sense/Board ADC path MCLK Distribution Distribute MCLK (from clock board) to all channel modules. Relay Driver Analog Multiplexer PPMU monitor/Diagnostics/Calibration signals to board ADC on I/F module Filter for PinPMU power supply MCLK distribution detail: Differential ECL Signals (2 pairs per channel module) Impedance controlled, 50 Ohm terminations Reference Level: Vcc = 3.3V (Compatible with Test processor CMOS Inputs) The Relay Module provides access to the frontplane. In detail, it contains the following circuitry: Frontplane interface Diagnostic interface (Analog Multiplexers) MCLK distribution 3 Relays for each channel: AC Relay 50, 6 pins DC Relay, 4 pins PMU Relay, 4 pins 8 Central Relays for DC-rail, GND-sense and Board ADCs Temperature measurement circuit/sensor 17 - PinScale Cards

34 PS3600/HSM Relay Module Components
Temperature Sensor MCLK Distribution Distribute MCLK (from clock board) to all channel modules. Analog Multiplexer PPMU monitor/Diagnostics/Calibration signals to board ADC on I/F module Filter for PinPMU power supply Linear Regulators, DC/DC Converter Central Relay 7 relays for DC rail/GND-sense/Board ADC path MCLK distribution detail: Differential ECL Signals (2 pairs per channel module) Impedance controlled, 50 Ohm terminations Reference Level: Vcc = 3.3V (Compatible with Test processor CMOS Inputs) The Relay Module provides access to the frontplane. In detail, it contains the following circuitry: Frontplane interface Diagnostic interface (Analog Multiplexers) MCLK distribution 7 Central Relays for DC-rail, GND-sense and Board ADCs Temperature measurement circuit/sensor 17 - PinScale Cards

35 PS800 Repair Module Exchange (1) 1. Remove channel module
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap 1. Remove channel module Extractor Tool: E 2. Scrape off gap filler using the flat end of the extractor tool Gap Fillers are included within: Channel module Interface/Relay module 3. When assembling modules, always use new gap filler After removing the channel module screws, disconnect the channel modules by using the extractor tool. Gap filler is included with the following service parts: channel module relay module interface module screw kit. 17 - PinScale Cards

36 PS800 Repair Module Exchange (2)
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap Case 1: One channel module to be exchanged Clean heat conductors with an ESD-safe brush Part Number: Make sure to remove any metal filings around the holes in the heat sink! Use a powerful magnifying glass or a microscope to detect very small filings. They can cause short circuits on the board and damage the test system. 0.3 mm 17 - PinScale Cards

37 PS800 Repair Module Exchange (3)
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap Case 2: All channel modules have to be removed due to the need to exchange Relay Module or Interface Module. Replace both heat conductors on the heat sink Heat conductors: E (Small – relay module side) E (Large – interface module side) Exchange relay module and heat conductor: Heat conductor Important for the repair Heat conductors fulfill the role of electric isolation. It is absolutely mandatory to renew the heat conductors during the repair. Missing heat conductors may cause all eight modules to become damaged. Exchange interface module and heat conductor: Heat conductor When exchanging the relay module or the interface module all 8 channel modules have to be removed. To obtain access to the screws, the heat conductor on the relay module side or the interface module side has to be removed. Both heat conductors should be replaced with new ones. They are included with the interface module and relay module service parts. 17 - PinScale Cards

38 PS3600/HSM Repair Module Exchange (1)
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap PS3600/HSM Repair Module Exchange (1) 1. Remove screws and channel module cover, then remove connector. 2. Remove screws. Disconnect channel module using the extractor tool. Extractor Tool: E 3. Remove channel module: Lift module with one hand. Slide module out by pushing the golden RF-connector with the other hand. Do not move the modules sideways to avoid damage to the relays. After removing the channel module screws the channel modules can be disconnected by using the extractor tool. For more details see the Service Guide Part 2. 17 - PinScale Cards

39 PS3600/HSM Repair Module Exchange (2)
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap 4. Scrape gap filler using the flat end of the extractor tool. When assembling modules use new gap filler Gap Filler Spare Part E (Small – Driver-Receiver) E (Large – Test Processor) Take care that no pins are bent on the channel module or interface module. Gap filler is included with the following service parts: channel module relay module interface module screw kit. 17 - PinScale Cards

40 PS3600/HSM Repair Module Exchange (3) Replace heat conductors if all
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap Replace heat conductors if all channel modules need to be removed. Heat conductors: E (relay module side) E (interface module side) 6. Exchange relay module and heat conductor: Heat conductor: E Important for the repair Heat conductors fulfill the role of electric isolation. It is absolutely mandatory to renew the heat conductors during the repair. Missing heat conductors may cause all eight modules to become damaged. 7. Exchange interface module and heat conductor: Heat conductor: E When exchanging the relay module or the interface module all 8 channel modules have to be removed. To obtain access to the screws, the heat conductor on the relay module side or the interface module side has to be removed. Both heat conductors should be replaced with new ones. They are included with the interface module and relay module service parts. 17 - PinScale Cards

41 PS3600/HSM Repair Module Exchange (4) 8. Assemble board cable
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap 9. Sort cables front side: X1 X2 X3 X back side: Y1 Y2 Y3 Y4 8. Assemble board cable and relay module The board cable is a separate part E and not included in the relay module support part. So it needs to be disassembled from the old relay module and installed at the new relay module. 17 - PinScale Cards

42 Torque Specs Align module connectors properly during assembly
... Ensure You‘re ESD Protected! Wear ESD shoes Wear ESD coat Wear ESD Wrist Strap Align module connectors properly during assembly Insert screws in the given order, finger-tight first. Torque screws down to 0.8 Nm in the given order. Use Torque wrench: , T8 bit: PS800 PS3600 Hand tight Hand tight 0.8 Nm 0.8 Nm 17 - PinScale Cards

43 Module Exchange – Ground Checking
The display must show more than 100kOhm Measuring point: DCCOM (-) on the interface board Measuring point: metal cover of the channel board 17 - PinScale Cards

44 PinScale HX Key Characteristics:
CPA x2 – Channel Pair Assembly FPIB – Frontplane Interface Board BIB – Backplane Interface Board Clock Module Key Characteristics: Data rate of 6.4 Gbps, 8 Gbps or 12.8 Gbps [6.4 Gbs standard] 4 differential channels Pattern and Loopback modes [license dependant] Jitter and skew injection Each HXA card has two differential (or 4 single ended) drive and two differential (or 4 single ended) receive channels. It also provides the following features: • Synchronisation to the DUT data or DUT clock timing • Jitter injection from an on board generator or external source • Common mode measurements and injection • Accessible Loopback paths with or without signal conditioning • Normal DC measurements. 17 - PinScale Cards

45 Installation Requirements
PinScale 3600 and HXA are compatible and can use the same DC-DC resource HXA assemblies require power to be supplied by p/n E8001-6x514 DC/DC assemblies ( - 6x515 or -6x513 P/N DC/DC’s are NOT to be used for HXA) Autotransformer E8005A may be required if filling scheme exceeds 42 digital cards of any type i.e >36kVA. Note this may also require change to primary voltage requirements for site [Reference Pre-Site Manual] SmarTest SW or later (5.4.2 recommended) 17 - PinScale Cards

46 HXA Block Diagram DC Bypass Mode Mux x4 Mode Loopback Mode DUT Board
Tester DUT Comp HD1+ HD1– RCV_3 REFCLK RCV_1 RCV_2 RCV_0 DRV_0 DRV_1 DRV_2 DRV_3 HR1+ HR1– Driver 1:2/1:4 Demux Retiming unit Rx Tx Pins 2:1/4:1 Mux DLL Drv DRVEN DC Bypass Jitter Modulation Jitter injection Delay Tracking Fine Delay Control Unit TRD TRKOUT TRKIN Receiver Clock Synthesizer Pin Scale 3600 channels Loopback Channel Pair Assembly 1 DC Bypass Mode Mux x4 Mode Loopback Mode Although the HXA card contains two fully differential drive and receive channels, for simplicity, the figure below shows only a single drive and receive channel. A drive/receive unit is termed a Channel Pair Assembly (CPA) i.e. each HXA card is made up of two CPAs. This figure shows only one CPA. This figure illustrates the principle of the re-timing of either 2 or 4 Pin Scale 3600 channels (per CPA) to achieve the final data rates you require. Pin Scale support for each HXA card: • For a data rate of 7.2 Gbit/s you need 4 Pin Scale 3600 channels (2 drive, 2 receive). • For a data rate of 12.8 Gbit/s you need 8 Pin Scale 3600 channels (4 drive, 4 receive) • Further 6 Pin Scale 3600 channels (4 reference clock, 2 drive enable) are needed for the timing and drive enable function. As each Pin Scale 3600 board has 32 single ended channels that can be configured as drive or receive, these needs can be covered by one Pin Scale board. 17 - PinScale Cards

47 Pogo Block Allocation Card cage Pogo Block Slot Numbers
HXA card pogo cable S2 (n-1) S2 (n) Card cage Pogo Block 108 107 106 105 308 307 306 305 104 103 102 101 304 302 301 303 Slot Numbers HXA card Low Speed Pogo Block (e.g. block 302) HXA card High Speed Pogo Block (e.g. block 301) Pin Scale Pogo Blocks (e.g. blocks 103, 104) Slot for HXA card (e.g. Group 1, slot 2). Slot for Pin Scale card (e.g. Group 1, slot 3). Card Placement • Pin Scale boards should be placed into every odd numbered slot starting with slot 1. • HXA cards should be placed into every even slot starting with slot 2. Pogo Blocks • Pin Scale boards service two S1 pogo blocks starting with the lowest number (e.g. 101 & 102 for card cage 3 (group 1). • HXA cards service two S2 pogo blocks starting with the lowest number (e.g. 301 & 302 for card cage 3 (group 1). The lowest number is the high speed block and the next higher number is the low speed block. 17 - PinScale Cards

48 Pogo Block Assignment Low Speed Pogo Block High Speed Pogo Block
PIN Low Speed High Speed PIN 1 LD1[0] Lane 1 Driver 0 Lane 1 Driver + HD1+ 1 2 LR1[0] Lane 1 Receive 0 Lane 1 Receive + HR1+ 2 Pogo Pins 1 1 1 3 1 1 1 1 1 LD1[2] Lane 1 Driver 2 Lane 1 Driver – HD1– 1 1 1 1 1 1 1 3 1 4 LR1[2] Lane 1 Receive 2* Lane 1 Receive – HR1– 4 Pin Scale Data 2X High Speed I/O Data 5 LD2[0] Lane 2 Driver 0 Lane 2 Driver + HD2+ 5 6 LR2[0] Lane 2 Receive 0 Lane 2 Receive + HR2+ 6 DUT Board PinScale 3600 (200M to 3600M) ) 7 LD2[2] Lane 2 Driver 2 Lane 2 Driver – HD2– 7 8 LR2[2] Lane 2 Receive 2* Lane 2 Receive – HR2– 8 High Speed Extension Card (800M to 10G+) ) 9 REFCLKD1 Lane 1 MUX Ref. Clock Lane 1 Driver 1 LD1[1] 9 10 REFCLKR1 Lane 1 DEMUX Ref. Clock Lane 1 Receive 1 LR1[1] 10 ) DUT 11 REFCLKD2 Lane 2 MUX Ref. Clock Lane 1 Driver 3 LD1[3] 11 93K Card Cage 12 REFCLKR2 Lane 2 DEMUX Ref. Clock Lane 1 Receive 3 LR1[3] 12 Pin Scale Data 4X Control Signals 13 LD1LEVSEL Lane 1 Level Select Lane 2 Driver 1 LD2[1] 13 14 LD2LEVSEL Lane 2 Level Select Lane 2 Receive 1 LR2[1] 14 15 TRKIN Timing Tracking In Lane 2 Driver 3 LD2[3] 15 16 TRKOUT Timing Tracking Out Lane 2 Receive 3 LR2[3] 16 17 MODIN Mod. Source In Mod. Source Out MODOUT 17 * Pins used for outputting common mode evaluation signal 17 - PinScale Cards

49 Model File ANALOGBOARD section
                     The HXA card is specified in the ANALOGBOARD section of the model file. The HXA card setups are licensed and hence specified on a per board level.  ANALOGBOARD 301: type = HXA, speed = 12.8 Gbps, loopback, pattern, tracking Set tracking mode enabled Set pattern mode enabled Set loopback mode enabled Set the speed (correct values need to be defined) HXA card Pin Scale 104 103 102 101 304 302 301 303 Slot Numbers Pogo Blocks High Speed pogo block (n-1) S1 S2 Set the board type The logical board address for the HXA board you are defining (lowest S2 pogo block number corresponding to the HXA board slot) 12.8 is now supported. Note: In a Standard configuration, Analog board section only requires the minimum information as shown above. Default PS3600 boards outputs are assumed by software. Custom configuration require more in depth data be added in the Board Conf Section to indicate which PS3600 boards are to be assigned to which HXA’s. (see next slide) 17 - PinScale Cards

50 Pin Scale HX-Model File Example
IOCHANNEL :HW = PS3600, speed = 1800Mbps, smem = 2M, vmem = 14M, tim = w256-d8-r8, diff :HW = PS3600, speed = 3600Mbps, smem = 2M, vmem = 14M, tim = w256-d8-r8, diff :HW = PS3600, speed = 1800Mbps, smem = 2M, vmem = 14M, tim = w256-d8-r8, diff # group 6: 409: type = HXA, speed=12800Mbps, loopback, pattern 411: type = HXA, speed=12800Mbps, loopback, pattern 413: type = HXA, speed=12800Mbps, loopback, pattern 415: type = HXA, speed=12800Mbps, loopback, pattern # group 8: 429: type = HXA, speed=12800Mbps, loopback, pattern If this where a standard configuration, information under group 6 would be listed under the analog section and no more info required. As this is page one of two, the next slide represents ‘Non Standard’ configuration where HXA and PS3600 must be assigned to each other (board conf section). 17 - PinScale Cards

51 Model File BOARDCONF section
This section is only required for specifying non standard routing, The routing can be specified on a per module (CPA) level, since the routing can be specified differently for each module. BOARDCONF 3011: type = HXA, muxd=10301/10302/10303/10304, clkd=10305, termd=10306, muxr=10307/10308/10309/10310, clkr= : type = HXA, muxd=10312/10313/10314/10315, clkd=10316, termd=10401, muxr=10402/10403/10404/10405, clkr=10406 Specifies the Pin Scale channel used for the receiver clock Specifies the Pin Scale mux channels for the HXA board receiver (0-4 channels)(LR rcvr inputs) Specifies the Pin Scale channel used for "Drive Enable“ (level select) Specifies the Pin Scale channel used for the driver clock Specifies the Pin Scale mux channels for the HXA board driver (0-4 channels)(LD drivers inputs) HXA card Pin Scale 104 103 102 101 304 302 301 303 Slot Numbers Pogo Blocks High Speed pogo block (n-1) S1 S2 The fourth digit specifies the Channel Pair Assembly (module) number of the HXA board (1= lane 1, 2=lane 2) The first three digits specify the logical board address for the HXA board you are defining (lowest S2 pogo block number corresponding to the HXA board slot). Explanation of the abbreviations HXA defines a High Speed Expansion card muxd represents the Pin Scale channels LD1[0] to LD1[3] and LD2[0] to LD2[3] clkd is REFCLK1 and REFCLK3 termd is DRVEN1 and DRVEN2 muxr represents the Pin Scale channels LR1[0] to LR1[3] and LR2[0] to LR2[3] clkr is REFCLK2 and REFCLK4 Because there are only 16 Pin Scale channels per pogo block, you can see from the above example that the first 16 Pin Scale channels use the pogo block 103 and the subsequent Pin Scale channels (termd, muxr, clkr) use the next (Pin Scale) pogo block, which is block 104.

52 Pin Scale HX-Model File Example (continued)
# Group 6: # Board ID: HS-Pogo(sw) HS-Pogo(hw) LS-Pogo(sw) LS-Pogo(hw) Max. Mux # same 410 same 4 # same 412 same 4 # same 414 same 4 # same 416 same 4 4091: type = HXA, muxd=21001/20909/21003/20911, clkd=21009, termd=21013, muxr=21002/20910/21004/20912, clkr=21010 4092: type = HXA, muxd=21005/20913/21007/20915, clkd=21011, termd=21014, muxr=21006/20914/21008/20916, clkr=21012 4111: type = HXA, muxd=21201/21109/21203/21111, clkd=21209, termd=21213, muxr=21202/21110/21204/21112, clkr=21210 4112: type = HXA, muxd=21205/21113/21207/21115, clkd=21211, termd=21214, muxr=21206/21114/21208/21116, clkr=21212 4131: type = HXA, muxd=21401/21309/21403/21311, clkd=21409, termd=21413, muxr=21402/21310/21404/21312, clkr=21410 4132: type = HXA, muxd=21405/21313/21407/21315, clkd=21411, termd=21414, muxr=21406/21314/21408/21316, clkr=21412 4151: type = HXA, muxd=21601/21509/21603/21511, clkd=21609, termd=21613, muxr=21602/21510/21604/21512, clkr=21610 4152: type = HXA, muxd=21605/21513/21607/21515, clkd=21611, termd=21614, muxr=21606/21514/21608/21516, clkr=21612 # Group 8: # same 430 same 4 4291: type = HXA, muxd=23001/22909/23003/22911, clkd=23009, termd=23013, muxr=23002/22910/23004/22912, clkr=23010 4292: type = HXA, muxd=23005/22913/23007/22915, clkd=23011, termd=23014, muxr=23006/22914/23008/22916, clkr=23012 Non Standard configuration – HXA ports must be assigned to PS3600 ports. This info is critical in diagnostic troubleshooting. 17 - PinScale Cards

53 Diagnostic and Calibration Prerequsites
IMPORTANT: All associated PinScale 3600 hardware MUST be passing Diagnostics BEFORE the HEXT test is run. If not, repair the PS3600 hardware first! In addition to selecting any HXA boards that you wish to test; You MUST also select ALL associated PinScale 3600 boards. To be safe: Select ALL PS3600 boards in cardcages where you have ANY HXA boards selected. Diagnostic – HEXT test Calibration – Calibration of the HXA is included when full system calibration is performed E7996C Standard Configuration P/N E NOTE: Custom configurations require a custom Diag/Cal board NOTE: Associated PS3600 H/W must be passing all diagnostic tests. (If not, repair the PS3600 H/W 1st) 17 - PinScale Cards

54 Trouble Shooting Possible causes for HXA diagnostic failures:
Bad Pogo Block on PS or HXA Bad HXA board Bad Pin Scale board Defective HXA diagnostic / calibration board Troubleshooting Recommendations: Repeat diagnostic tests to verify if solid Visual inspection of pogo blocks i.e. HXA and associated Pin Scale channels Swap of HXA with known good position Swap of Pin Scale board Digital Diagnostics (FRU repair level) HXA Diagnostics (Whole board replacement) Note: Experience has shown that reseating HXA boards can clear up some failures 17 - PinScale Cards

55 Trouble Shooting Decoding of di_log_file.xxxx
Identifying Suspect Failing Boards Example di_log_file failure [HEXT header] T HEXT (DIG):Corretto Diag test (100.00ns) In 6 corretto board(s), the following 12 corretto CPA(s) were detected: Crd S M D D D D R R R R3 DCLK RCLK DRVEN _________________________________________________________________________ HXA card shown in relation to what port are tied to which PS3600 boards/pins. 17 - PinScale Cards

56 Trouble Shooting Decoding of di_log_file.xxxx (Continued)
Identifying Suspect Failing Boards Example di_log_file failure: VERIFY DATA-IN RELAIS T HEXT Error: CHAN 12701: [D0] Data-In Relais of "HXA325:1": I_exp = uA, [ uA] : I_meas = uA, 147.1% : *** # Data-In T HEXT Error: CHAN 12703: [D1] Data-In Relais of "HXA325:1": I_exp = uA, [ uA] : I_meas = uA, 276.9% : *** # Data-In T HEXT Error: CHAN 12709: [DCLK] Data-In Relais of "HXA325:1": I_exp = uA, [ uA] : I_meas = uA, 308.0% : *** # Data-In T HEXT Error: CHAN 12901: [D2] Data-In Relais of "HXA325:1": I_exp = uA, [ uA] : I_meas = uA, 106.9% : *** # Data-In Diag Test HEXT PS3600 In Use Signal Pin HXA HXA 325 Board Lane 1 Failed Measurement 17 - PinScale Cards

57 Trouble Shooting Decoding of di_log_file.xxxx (Continued)
Identifying Suspect Failing Boards Example di_log_file failure: Clockmodule failure pattern T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS17/08: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockC17/08: F_exp = GHz, [ GHz] : F_meas = GHz, % : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS32/15: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockC32/15: F_exp = GHz, [ GHz] : F_meas = GHz, % : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS09/04: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockC09/04: F_exp = GHz, [ GHz] : F_meas = GHz, % : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS16/07: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockC16/07: F_exp = GHz, [ GHz] : F_meas = GHz, % : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS19/08: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockC19/08: F_exp = GHz, [ GHz] : F_meas = GHz, % : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS32/13: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockC32/13: F_exp = GHz, [ GHz] : F_meas = GHz, % : *** # Embedded diag T HEXT Error: CHAN 10709: Embedded diag of "HXA305",clockmoduleDiag,CLKM,LockS05/02: F_exp = GHz, [ GHz] : F_meas = GHz, 433.3% : *** # Embedded diag Diag Test HEXT PS3600 In Use Affected HXA board Failed Diag Step Failed Measurement 17 - PinScale Cards

58 Spare Parts E7996-68511 HXA Replacement Board Assembly
E HXA Exchange Board Assembly E HXA Pogo Cable E HXA Calibration / Diagnostic board 17 - PinScale Cards

59 DC Scale Cards – DPS32 & VI32 Interface Module x8 Channel Modules Relay Module 17 - PinScale Cards

60 Pogo Assignment 17 - PinScale Cards

61 Channel Assignment Channel assignment is printed on metal cover
Logical Logical Board A Board B Logical Logical Board B Board A Channel assignment is printed on metal cover Each logical board is connected to one pogo block. DPS32 and VI32 require the Universal DC/DC. The positions of the individual channel modules are printed on the metal cover of the digital card. Note that the card is divided into two logical boards, where each supports one pogo block with 16 channels. Logical board 1 will always be an odd channel board. (i.e , …) Logical board 2 will always be an even channel board. (i.e. 102, 104, …) 17 - PinScale Cards

62 DC Scale Model file # Example model file: GLOBAL testhead = TH_8CC # TH_2CC | TH_4CC | TH_8CC dut_interface = SOC # F330 | SOC | EXHIBITION # hpib_interface = vxi11/ /gpib0 # hpib | vxi11/ /gpib0 # ppu_device = /dev/tty1p0 device_maintenance = on IOCHANNEL :HW = PS800, speed = 800 Mbps, vmem = 54M, smem = 2M, tim = w256-d8-r8 DPS 1: type = GPDPS 3: type = MSDPS, channels = 8 : type = DCS-VI32 : type = DCS-DPS32 Keywords for DC-Scale cards start with DCS. There are no further options 17 - PinScale Cards

63 Klick left mouse button on arrow to display sub-test-list.
Diagnostic Klick left mouse button on arrow to display sub-test-list. Recommended: Diagnostic Board E7010E Diagnostic CDPS Subtests: Force/Measure DC-Connectivity Ganging AC Connectivity Tests the Pogo cable connection to DUT Channel Memory Board-Supply Channel Communication Channel Supply All sub tests are card internal, except the AC connectivity test. 17 - PinScale Cards

64 17 - PinScale Cards


Download ppt "Verigy V93000 Service Training"

Similar presentations


Ads by Google