1. The physical network Unit objective: Identify network cables and connectors, and use networking tools

2. Topic A Topic A: Network cable and connector types Topic B: Cable and connector properties Topic C: Networking tools

3. Fiber optic cable Carries light-based data Strands of glass or plastic Components contnued

4. Fiber optic connectors ST SC LC Other connectors

5. Twisted-pair cable Copper wire Unshielded twisted-pair Shielded twisted-pair Connectors –RJ-45 –RJ-11

6. Coaxial cable Found in older networks continued

7. Coaxial cable, continued RG-8 and RG-58 used in Ethernet RG = Radio Guide Stranded or solid Impedance in ohms, Ω Thicknet cables are RG-8 Thin Ethernet cables are RG-58

8. Topic B Topic A: Network cable and connector types Topic B: Cable and connector properties Topic C: Networking tools

9. Fiber optic cable Two types –Single-mode –Multimode Commonly used for long distances and backbones Benefits: –Thinner and lighter weight –Higher carrying capacity –Use of digital signals –Less signal degradation –Less interference –Non-flammable –More secure

10. Common UTP categories

11. Additional TP categories

12. Stranded vs. solid Solid –Thicker, more protective covering –Less flexible –Best for longer network runs and fixed wiring Stranded –Thinner protective covering –More pliable –Useful for shorter-distances and movable wiring

13. Straight-through and cross-over Straight-through –TP cable; both ends follow either 568A or 568B –Used to connect computers to hub or switch Cross-over –TP cable; one end is wired using 568A, and the other using 568B –Used to connect two computers together

14. Pin numbering of RJ-45 connector

15. T1 crossover cable Connects two T1 devices together without a network device between them Cable end 1Cable end 2 Pin 1Pin 4 Pin 2Pin 5 Pin 4Pin 1 Pin 5Pin 2

16. RG standards StandardImpedanceCore sizeUses RG-6/U 75  1.0 mmCable and satellite television; cable modems RG-6/UQ 75  1.0 mmQ stands for quad: 4 layers of shielding, compared to RG-6/U, which has 2. RG-8/U 50  2.17 mmThicknet network backbones; amateur radio. RG-9/U 51  2.17 mmThicknet network backbones RG-11/U 75  1.63 mmCable and satellite television, video surveillance; thicker than RG-6. Used underground or for outdoor antennae drops. RG-58/U 50  0.9 mmThin Ethernet; radio; amateur radio. RG-59/U 75  0.81 mmBaseband video in closed-circuit television; cable television.

17. RG standards StandardImpedanceCore sizeUses RG-6/U 75  1.0 mmCable and satellite television; cable modems RG-6/UQ 75  1.0 mmQ stands for quad: 4 layers of shielding, compared to RG-6/U, which has 2. RG-8/U 50  2.17 mmThicknet network backbones; amateur radio. RG-9/U 51  2.17 mmThicknet network backbones RG-11/U 75  1.63 mmCable and satellite television, video surveillance; thicker than RG-6. Used underground or for outdoor antennae drops. RG-58/U 50  0.9 mmThin Ethernet; radio; amateur radio. RG-59/U 75  0.81 mmBaseband video in closed-circuit television; cable television.

18. Topic C Topic A: Network cable and connector types Topic B: Cable and connector properties Topic C: Networking tools

19. Crimper

20. Coax crimper Terminating a coaxial Thinnet cable to a BNC connector

21. Twisted-pair cable crimper

22. Punchdown tool

23. Using a punchdown tool 1.Insert the wire between the two metal blades on the punchdown block. There is one wire per contact in the punchdown block. 2.Place the punchdown tool on top of the wire. (Remember to have the correct side of the tool facing up.) 3.Apply pressure to the wire until you hear a snap. This snap is from the spring mechanism inside the tool.

24. Cable testing device Test physical cables and network functions Single LAN type device or multiple LAN type device

25. Physical cable tests Locating incorrectly wired cables, open cables, and shorts Locating missing cables Locating cables that don’t support your network type Testing hub connections Testing PC connections Testing installed cables Testing patch cables Locating and tracing inactive cables

26. Network function tests Verifying that a PC or switch is powered on Specifying whether a device is a network PC or a switch Displaying the maximum network connection speed to the device Verifying PC-to-switch speed, and data transmission and port speed or duplex mismatch Verifying switch-to-switch data transmission Determining if a straight-through or crossover patch cable is required Finding speed bottlenecks on LANs Monitoring a LAN link between two devices

27. Toner probe Amplifier probe Locate, identify, and trace wires or cables Works with a tone generator

28. Using a tone probe 1.Set the tone generator to tone. 2.Test the tone generator. 3.Connect the tone generator to one end of the cable you want to trace. 4.Use the probe to identify where the cable comes into your patch panel or 110 block. Move to the cable bundle and identify the cable in the bundle that runs to where you’ve connected the tone generator. 5.Disconnect the tone generator and turn it off.

29. Loopback plug Test ports Specific to type of port Ethernet loopback –10 and 100 Mbps –Gigabit Network loopback plug - can make your own or buy commercial

30. Multimeters Use to measure electricity from power supply or computer component Available in digital and analog models

31. Measuring resistance 1.Turn off the device you’re measuring and disconnect it from its power source 2.If necessary disconnect the device from its circuit 3.Set the multimeter to read resistance 4.Touch the two leads of the multimeter together 5.Touch the black and red probes to either side of the circuit to be measured, and read the resistance from the meter’s display

32. Measuring voltage 1.The power supply must be on 2.Set your multimeter to read either DC or AC voltage 3.Touch the black probe to the ground, and touch the red probe to the spot where you want to measure the voltage

33. Measuring current 1.Break the circuit 2.Insert the meter in the break 3.Read the current flowing through circuit Can also use an ammeter or clamp- ion ammeter to measure current flow

34. Measuring continuity 1.Set multimeter to display resistance 2.Look for circuits with zero resistance If your multimeter includes a continuity mode, you can use that. In continuity mode, multimeter sounds a tone whenever it detects a closed circuit

35. Unit summary Identified network cables and connectors, and used networking tools