Presentation is loading. Please wait.

Presentation is loading. Please wait.

A+ A Guide to Hardware Week 3 Form Factors and Power Supplies.

Similar presentations


Presentation on theme: "A+ A Guide to Hardware Week 3 Form Factors and Power Supplies."— Presentation transcript:

1 A+ A Guide to Hardware Week 3 Form Factors and Power Supplies

2 Objectives Learn about different form factors and computer cases. Learn how electricity is measured Learn how to protect your computer system against damaging changes in electrical power Learn about Energy Star specifications Learn how to troubleshoot electrical problems 2

3 Introduction Power supply: passes power to PC components Elements driving type of power supply used in a PC: –The motherboard –The form factor of the computer case Energy Star devices: designed to save energy Electricity topics covered: –Measurements of electricity –How electricity is delivered –Protecting a PC from electrical damage –Changing a defective power supply 3

4 4 Computer Case, Motherboard, and Power Supply Form Factors Form factor –Specifies size, shape, features of a hardware device Form factor for motherboard is chosen first –Same form factor is used for case and power supply Using the same form factor assures you that: –The motherboard fits the case –The powers supply cords provide proper voltage –Holes in the motherboard align with holes in the case –Holes in the case align with ports off the motherboard –Wires on the case match connections on motherboard

5 5 Types of Form Factors AT (Advanced Technology) form factor –Specified motherboard dimensions of 12” x 13.8” –Utilized by IBM AT PC in the 1980s Baby AT form factor –Specified motherboard dimensions of 13” x 8.7” –Industry standard form factor from 1993 to 1997 ATX form factor –Specified motherboard dimensions of 12” x 9.6” –Open specification that is most commonly used today –Includes all AT voltages plus a +3.3-volt circuit

6 A+ Guide to Hardware, Sixth Edition6 Table 3-1 Sockets for Intel processors used for desktop computers

7 7 The CPU on an ATX motherboard sits opposite the expansion slots and does not block the room needed for long expansion cards

8 8 Types of Form Factors (continued) DTX – Pioneered by AMD, backward compatible to ATX MicroATX form factor –Reduces number of I/O slots on the motherboard BTX (Balanced Technology Extended) form factor –Focuses on reducing heat and supporting motherboard LPX and Mini-LPX form factors –Designed for low-end PC motherboards NLX form factor –Developed to improve the LPX form factor Backplane Systems (Active and Passive) –Use boards with slots, but little or no circuitry

9 9 Back Plane

10 10 Back Plane Systems

11 A+ Guide to Managing and Maintaining your PC, 6e11 Improved airflow in a BTX case and motherboard makes it unnecessary to have a fan on top of the processor

12 12 Types of Cases Computer case (chassis) –Houses power supply, motherboard, cards, drives –Panel switches/lights are used to control/monitor PC Desktop cases –Motherboard on the bottom, power supply to the rear Tower cases –Are up to 2 feet high and can contain several drives Notebook cases –Used for all portables and have desktop components Others –Wikipedia sources

13 13 Tower and desktop cases

14 14 Measures and Properties of Electricity Successful PC technicians: –Understand electricity –Know how to use electricity –Know how to measure electricity –Can protect computer equipment from electricity Units used to measure characteristics of electricity –Volt, amp, ohm, and watt

15 15 AC and DC Alternating current (AC) –Oscillatory current driven by an alternating voltage –Example: house current oscillates at 60 Hz Direct current (DC) –Single direction current driven by constant voltage –Required by computer in small amounts, such as 5 V Rectifier: converts AC to DC Transformer: changes ratio of current to voltage Power supply acts as a transformer and rectifier and conditioner.

16 Cost of a power supply can be reduced by cheapening up the components. Cheap supplies will remove –Transient i/p filter, meaning the supply has a better chance of blowing if line voltage fluctuates. –Remove PFC (power factor correction), supply will become inefficient, converting as little as 65% of ip to op. Active PFC can improve performance to 98%. Contributes to cleaner and better o/p performance. –Lighter transformers, replaced by integrated ccts. Unable to handle high current loads. Not all PS are Created Equal 16

17 17 Measures of electricity

18 18 A transformer keeps power constant but changes the ratio of current to voltage

19 19 Hot, Neutral, and Ground Completing a circuit: –AC travels from power station to house on a hot line –AC travels from panel to device using black (hot) wire –AC flows out of device circuit in a white (neutral) wire –AC returns to power station on a neutral line Short circuit: failure due to excess flow of electricity –Fuses protect circuits by melting wire (breaking circuit) –Grounded neutral lines pass detoured AC to earth Lines in three-prong plugs: hot, neutral, and ground –Verify wiring of outlet for plug using a receptacle tester

20 20 Normally, electricity flows from hot to neutral to make a closed circuit in the controlled environment of an electrical device such as a lamp

21 21 Use a receptacle tester to verify that hot, neutral, and ground are wired correctly

22 22 Some Common Electric Components Materials used to make components: –Conductors: weakly resist flow of current; e.g., copper –Insulators: highly resist flow of current; e.g., ceramics –Semiconductors: allow flow if charged; e.g., silicon Transistor –Used to switch current on (1) and off (0) –Also used to amplify current –Made of three layers of semiconductor material –Charge applied to center layer controls switching

23 23 Symbols for some electronic components and for ground

24 24 Some Common Electric Components (continued) Capacitor –Holds electrical charge for a period of time –Used to create even flow of current in a PC Diode –Allows electricity to flow in one direction only –Used to rectify current (convert AC to DC) Resistor –Controls the amount of current flowing through device –Degree of resistance is measured in ohms

25 25 Capacitors on a motherboard or other circuit board often have embedded crossed lines on top

26 26 Protecting Your Computer System Electrical threats to a computer system: –Static electricity –Electromagnetic interference –Power surges Objectives in this section: –Understand nature of each threat –Learn how to protect your system from these threats

27 27 Static Electricity Static electricity (electrostatic discharge or ESD) –Due to charge difference between user and device –Touching device causes discharge, damaging device ESD is particularly severe in dry and cold climates How to protect system from ESD: –Use ground bracelet or ESD gloves –Touch computer case before touching components Safety rule: unplug power cord before working in case –Residual power in plugged device can cause damage

28 28 EMI (Electromagnetic Interference) Caused by magnetic fields generated by current flow RFI (radio frequency interference): –EMI in radio frequency range affecting reception The crosstalk problem –Data in cables crossing EM fields gets corrupted –Control crosstalk by shielding cables and power supply Use a tuned-down AM radio to detect EMI Other ways to protect a device from EMI: –Use line conditioners to filter out electrical noise –Move the PC to a new location

29 29 Surge Protection and Battery Backup Storms and uneven AC flow cause power surges Prevent power surges by installing an AC filter –Power bars (the expensive kind) Types of devices used to manage power surges: –Surge suppressors –Power conditioners –Uninterruptible power supplies (UPSs) Use devices with UL (Underwriters Laboratory) logo

30 30 Surge Suppressors Also called a surge protector Protects equipment from sudden changes in power –Works by absorbing and/or blocking the surge Recommended features: –Joules rating that is greater than 600 joules –Protection activated in less than 2 nanoseconds –Warranty for connected equipment and UL seal –Light indicating that surge protection is working –Data line protector for telephone line to modem, Network (RJ45). –Let-through voltage rating and line noise filtering

31 31 This surge suppressor has six electrical outlets, two phone jacks, and a power protection light. Protected by a 10 cent device called a Varistor.

32 32 Power Conditioners Sometimes called line conditioners Functions: –Protect against spikes or swells (voltage surges) –Raise voltage during brownouts (voltage sags) Load supported measured in watts or volt-amps (VA) Determining the VA needed to support your system: –Multiply the amperage of each component by 120 V –Add up the VA for each component.

33 33 Uninterruptible Power Supply UPS offers three benefits: –Conditions line to account for brownouts and spikes –Provides power backup when AC fails (blackout) –Provides protection against very high spikes Designs: standby, inline, and line-interactive Smart (intelligent) UPS: controlled with software What to consider when buying a UPS: –UPS rating should exceed VA load by at least 25 % –Degree of line conditioning –Warranties, guarantees, and service policies

34 34 Energy Star Systems (The Green Star) Energy Star systems have the U.S. Green Star –Indicates device meets energy conserving standards –Devices: computers, monitors, printers, copiers, faxes Goals of Energy Star (a.k.a. Green) standards: –Reduce overall electricity consumption –Protect and preserve natural resources How computer components meet standards –Uses standby program for switching to sleep mode –No more than 30 watts used during sleep mode

35 35 Power-Management Methods and Features Methods used to meet Energy Star standards: –Advanced Configuration and Power Interface (ACPI) Standard used by most desktops and notebooks Comprises four power-saving modes: S1 - S4 Some features controlled by BIOS, others by Windows –Advanced Power Management (APM) specification –AT Attachment (ATA) for various drives –Display Power Management Signaling (DPMS)

36 36 Figure 4-24 A power management BIOS setup screen showing power-management features

37 37 Energy Star Monitors Display Power Management Signaling (DPMS) –Specifications applying to video card and monitor –Allow both devices to simultaneously enter sleep mode Accessing energy settings in Windows 2000/XP –Right-click the desktop and select Properties The Display Properties dialog box opens –Click the Screen Saver tab If monitor is Energy Star–compliant, logo is at bottom –Click Power button to open Power Options Properties

38 38 Changing power options in Windows 7

39 39 Troubleshooting the Electrical System Problems can occur before or after boot Problems can be consistent or inconsistent Possible symptoms of an electrical problem: –The PC appears “dead” –The PC sometimes halts during booting –Error codes or beeps occur during booting –You smell burnt parts or odors Check the simple things first –Example: determine whether all switches are on

40 40 Problems with External Power Brownout (reduced current) may create issues –Check out other devices using the same circuit –Remove other devices to see if voltage increases Dealing with intermittent errors caused by noise: –Use a line monitor to monitor and condition voltage

41 41 Problems with Loose Internal Connections Can cause a system to appear dead or reboot itself Troubleshooting tasks: –Remove the cover of the case –Check all power connections Check cables linking power supply to motherboard Check cables linking power supply to drives

42 42 For an ATX or BTX power supply, the remote switch wire must be connected to the motherboard before power will come on

43 43 Problems that Come and Go Intermittent symptoms indicating a post-boot problem –The computer stops or hangs or reboots for no reason –Memory errors appear intermittently –Data is written incorrectly to the hard drive –The keyboard stops working at odd times –The motherboard fails or is damaged –Power supply overheats and becomes hot to the touch –The power supply fan becomes very noisy or stops Intermittent problems are often difficult to solve

44 44 Problems with an Inadequate Power Supply Power supply may not meet needs of new devices Testing for an adequate power supply –Make all devices in the system work at the same time –Example: copy files from new drive to old drive Simple solution: upgrade to a higher power supply Calculating total wattage needed by system –Multiply volts in circuit by amps required for device –Add all products to determine total wattage Power supply range: 200 watts to 600 watts

45 45 Problems with the Power Supply, Boards, or Drives Issues: –Inadequate or faulty power supply –Components drawing power might be bad Problems caused: –System hangs or gives intermittent errors –System reboots or does not boot at all Actions to take: –Isolate and remove any faulty expansion cards –Upgrade or switch the power supply –Test voltage output of power supply with a multimeter

46 46 Problems with the Power Supply Fan Defective fans usually hum before they stop working Response to diagnosis of defective fan –Replace fan or the entire power supply If replacement does not work, suspect another short Do not operate a PC if the fan does not work –Computers will overheat, damaging circuit boards Indirect sources of fan problems: –Shorts in drives, motherboard, or expansion cards

47 47 Power Problems with the Motherboard Bad contact between board component and chassis –Short can seriously damage the motherboard –Check for missing or extra standoffs (spacers) Shorts in the circuit on the motherboard –Look for damage to the bottom of the motherboard –Look for burned-out capacitors Frayed wires on connections can also cause shorts –Test hard drive cables connected to motherboard

48 48 Problems with Overheating Causes intermittent problems May also cause the system to reboot or not boot Temperature in a case should not exceed 100° F Some possible solutions: –Remove dust from power supply, vents, heat sink –Secure cables and cords with tie wraps –Install another exhaust fan on the rear of the case –Install a fan in expansion slot next to video card –Replace component that is damaged

49 49 Install one exhaust fan on the rear of the case to help pull air through the case

50 50 Replacing the Power Supply The power supply is a field replaceable unit (FRU) Criteria for replacement power supply to meet: –Uses the correct form factor –Adequately rated for power in watts –Has all power connectors needed by your system Before replacing power supply, test new device –Connect components to new power supply –Turn on PC and observe whether problem is solved –If problem is solved, perform replacement procedure

51 51 Summary Form factor: specifies size, shape, features of device Motherboard, power supply, and case share the same form factor, such as ATX Three types of cases: desktop, tower, and notebook Quantities that characterize electricity: voltage, current, resistance, and power Current flows from hot wires to neutral wires; excess current escapes through grounds

52 52 Summary (continued) AC supplied by power station is transformed and rectified before flowing into the PC Major components in a circuit board: transistor, capacitor, diode, resistor Electrical threats: ESD, EMI, uneven current flow, sudden power surges (or spikes) Energy Star standards promote energy conservation PCs comply with Energy Star standards by enabling devices to enter into a low power sleep mode

53 53 Power Supply basic system

54 Wave Forms Normal Linear Power Supplies 54

55 Power Supply Switching System 55

56 Pulse width modulation As more current is required, the power supply pulses on for longer durations. Hence the term switching. Switching Power Supply 56

57 57 The End


Download ppt "A+ A Guide to Hardware Week 3 Form Factors and Power Supplies."

Similar presentations


Ads by Google