1. Project Management Service
Laboratory Service
Job Site/Factory Service
Warranty
About the project management service it will divide in three parts: first is lab service it will help us to choose best sealant for the project,and The compatibility between the sealant and the backing material, and so on. The job sit service will help us to check whether the sealant works well

2. Project Management Service
Laboratory Service included:
Print Review
Adhesion Test
Compatibility Test
Staining Test
Others
Those tests will help us to avoid the problem

3. Standard Testing for Building Material
Adhesion Test (ASTM C794)
Compatibility Test (ASTM C 1087)
Staining Test (ASTM C 1248)
Quality Control in shop and on job site

4. Sufficient Bite and Glueline
Print Review
Sufficient Bite and Glueline
Glass or Insulating Glass W
Foam Backer
Rod D
BEFORE ANY PROJECTS STARTS, We will help you to calculate the required bite and glueline B
Frame
Spacer
Structure Sealant
B Structural bite
D Structural glueline
W Weatherseal bite

5. Structural Glazing Guidelines
Structural bite and Glueline thickness no less than 6 mm
Structural bite should larger than glueline thickness
Ideal Bite to Gueline thickness ratio is 1:1 to 3:1
Structural joint should be allow access through standard glazing tool and practice
On-site glazed units must be secured by a temporary fixing before structural sealant establish its strength and bonding, shop glazed units can be moved out when structural joint had been cured and adhered.

6. Adhesion Test (ASTM C794) Sealant Cleaning Solvent Primer
Before we do the test we will do the tests, provide me your job site sample,we will do the following test to you.
We will run adhesion test on the job site samples as per ASTM C 794 to ensure good adhesion
Peel-Strength
Primerless
Prepared Sample

7. Compatibility Test (ASTM C 1087)
Identify the materials Foam backer rod which discolour the sealant, cause the sealant lose adhesion, whether adhesion to the sealant
Identifies Materials Which Discolor the Sealant
Cause the Sealant to Lose Adhesion
Adhere to the Sealant

8. Staining Testing (ASTM C 1248)
Pressure
Pressure
Sometimes we will broke the stone to check whether the sealant staining the stone.
Select a Suitable Sealant to Prevent Staining

9. Project Management Service
Job Site/Factory Service:
Sealant Application Training
Field Adhesion Test
Deglazing
About the project management service it will divide in three parts: first is lab service it will help us to choose best sealant for the project,and The compatibility between the sealant and the backing material, and so on. The job sit service will help us to check whether the sealant works well

10. Sealant Application Training
Three Steps:
Cleaning
Primer (if required )
3. Sealant Application

11. Sealant Application Training
Standard Cleaning Procedure
——“Two-Cloth” Cleaning Method
Solvents:
Alcohol, Acetone, Isopropanol, Ethyl Acetate

12. Pour or dispense an acceptable solvent onto the cloth.
Wipe vigorously to remove contaminants.
a clean, white, lint free cloth
2 Cloth Cleaning Method: Solvent Clean
Explains the first stage of joint preparation/cleaning. The cleaning process is refered to
as the 2 Cloth Cleaning Method.
The paint surface is vigorously rubbed using a clean, white, lint free cloth that has been
soaked in solvent.
The combination of the rubbing and the solvent works to lift the waxes, dirt and oil from
the surface and suspends them in solution.
In the case of the wax film which is present on the surface of Polyester Powdercoat Paint
it is extemely important to clean the surface vigorously as the wax film is quite thick and
difficult to remove. It is important to recognise that a simple wipe with solvent will
not remove the wax. The degree of difficulty associated with removing the wax film is
also dependent on the colour of the paint. The colour effects the characteristics of the film.
Choice of cleaning solvent is also important. The solvent needs to be sufficiently aggressive
to remove the contaminants, particularly the wax, without effecting the underlying paint
surface.
Dow Corning recommends the use of White Spirits(ie, Contains about 20% Aromatics) 12
Notes:
硅宝科技

13. 2 3. Immediately wipe the cleaned area with a clean, dry cloth. 13
2 Cloth Cleaning Method: Solvent/Dirt Removal.
The next stage of the cleaning process requires that the residual solution consisting of the
waxes, dirt and oil suspended in the solvent is wiped from the surface using a second, clean,
white, lint free cloth.
This step is important because if the solvent is left to evapourate from the surface then the
contaminants which are suspended in the solution will be deposited back onto the surface
of the paint.
Once again choice of solvent is important. If the solvent is too volatile it will flash off
before it can be wiped away. This problem is even more pronounced in high temperatures.
An example is Methyl Ethyl Ketone which is both highly aggressive and will effect the paint
finish and also is highly volatile.
Cloths to be used should not be colored as the solvent will lift the dye from the cloth
and deposit it on the substrate surface which will effect sealant adhesion. 13
Notes:
硅宝科技

14. Application of Primer:

15. Two-part silicone sealant application
1.Butterfly Test
Apply Sealant to
Creased White Paper
Press Together
Well-Mixed
Poorly-Mixed
Every time, When you ready to apply the sealant, you should do *** to check the sealant mixed well.
2 situation, you should check your pump machine, try it again.
At the same time,you should do the to adjust the mix ratio
2.Snap-Time Test
Make Sure Whether the Mix Ratio is Correct

16. Deglazing

17. Deglazing

18. Project Management Service
Print Review
Adhesion Test
Compatibility Test
Staining Test
Deglazing
Specification Standard
keep records / documentation
10 Years Warranty
Keep Records / Documentation

19. Guibao New Production Plant