Presentation is loading. Please wait.

Presentation is loading. Please wait.

MCQ.

Similar presentations


Presentation on theme: "MCQ."— Presentation transcript:

1 MCQ

2 1. The following is the metal cutting process______________
Shaping Grinding Honing Lapping

3 2. In lathe machine , the function of bed is to ____________
Provide sliding surface for carriage Provide sliding surface for tailstock Support tailstock All (a) (b) & (c)

4 3. In lathe machine the, the function of headstock is
Support the carriage Support the tailstock Support the spindle All (a) (b) & (c)

5 4. In lathe machine, the function of tailstock is
Support the spindle Hold the main drive Hold the dead centre Both (b) & (c)

6 5. In lathe machine, the function of main drive is
Drive an electric motor Drive the spindle To change the spindle speed Both (b) & (c)

7 5. In lathe machine, the function of carriage is to
Support the spindle Hold & give feed to cutting tool To hold the dead center Both (b) & (c)

8 6. In lathe machine, the mechanism used for mechanized movements of the carriage is known as
Saddle Apron Cross-slide Compound rest

9 7. In lathe machine, the arrangement used for facilitating the tapper turning is known as
Compound rest Saddle Apron cross-slide

10 cross-slide Compound rest Apron Lead screw
8. In lathe machine the component which helps in thread cutting is known as ________________ cross-slide Compound rest Apron Lead screw

11 9. In lathe machine, the feed drive is placed between___________
Headstock & tailstock Tailstock & carriage toolpost & tailstock Main drive & lead screw

12 Apron Feed drive Electric motor Gear box
10. In lathe machine, the unit used for transmitting the motion from the main drive to the lead screw is known as _______________ Apron Feed drive Electric motor Gear box

13 Apron Cross-slide Split nut Drive nut
11. In lathe machine the component used for engagement & disengagement of lead screw is known as ______________ Apron Cross-slide Split nut Drive nut

14 12. In lathe machine, the tool like drill & reamer are hold by
Toolpost Headstock Spindle Tailstock

15 13. In lathe machine, the chuck is mounted on
Carriage Spindle Tailstock Apron

16 14. In lathe machine, the function of carriage is to
Hold the workpiece Hold the tool Support the tailstock Change the speed

17 Work piece length / distance between centre Height of lathe
15.The following parameter cannot be used for specifying the lathe machine Swing Work piece length / distance between centre Height of lathe Overall length of bed

18 Tool post Spindle Carriage None of above
16. In lathe machine, during drilling operation , drill bit is supported by Tool post Spindle Carriage None of above

19 17. Eccentric turning on lathe requires
Two jaw chuck Three jaw chuck Four jaw chuck Eccentric chuck

20 Perpendicular turning Taper turning Facing Finishing
18. In lathe machine, the tool motion is perpendicular to the axis of the lathe spindle during which of following operation Perpendicular turning Taper turning Facing Finishing

21 19. The chamfering helps in
Metal saving Avoiding the injuries to the persons handling the finished product Giving aesthetic look to the finished product Both (b) & (c)

22 Grooving Slitting Cutting Parting
20. The process of cutting a work piece into two parts on lathe machine is called as Grooving Slitting Cutting Parting

23 Improving the strength of material
21. The knurling helps in Improving the strength of material Providing a non-slip grip on the surface Saving the material Both (b) & (c)

24 Drilling Enlarging Boring Finishing
22. In lathe machine, the enlarging of the already existing hole in work piece is carried by the operation known as Drilling Enlarging Boring Finishing

25 Tailstock Spindle Carriage Lathe bed
23. In thread cutting operation on lathe machine the following element has to engage with lead screw Tailstock Spindle Carriage Lathe bed

26 Headstock & tailstock Lead screw & tailstock Apron & cross slide
24. In thread cutting operation on lathe machine, there has to be engagement between ________________ Headstock & tailstock Lead screw & tailstock Apron & cross slide Lead screw & split nut

27 25. The following operation is cannot be performed on lathe machine
Drilling Milling Boring None of above

28 26. In thread cutting operation on lathe machine ___________
The motion of carriage is manual The motion of carriage is mechanized The motion of carriage is perpendicular to the axis of workpiece Both (b) &(c)

29 29. In centre lathe machine, the gearbox or cone pulley is located in
Carriage Bed Headstock Tailstock

30 30. Turning tool is a __________________
Multipoint cutting tool Three point cutting tool Line cutting tool Single point cutting tool

31 31. The drill is a ________________
Multipoint cutting tool Two point cutting tool Line cutting tool Single point cutting tool

32 32. In drilling machine ___________
Drill is stationary & workpiece is rotating Drill is rotating & workpiece is stationary Drill is rotating & workpiece is rotating Drill is moving & workpiece is moving

33 Both linear & rotary motion None of above
33. In drilling machine, during operation the drill is given ___________ Only rotary motion Only linear motion Both linear & rotary motion None of above

34 34. In drilling machine, the linear motion of drill is called as _____
Speed Depth of cut Travel Feed

35 35. In drilling machine, the workpiece is mounted on
Spindle Bed Column Work table

36 36. In drilling machine, the drilling head is supported by ___________
Spindle Bed Column Work table

37 37. In drilling machine, the work table has _________________
Rotary motion about base Up & down motion along the axis Swing motion about the axis of column Both (b) & (c)

38 37. The drilling head contains
Work table Drive mechanism Feed mechanism Both (b) & (c)

39 38. Which of following operations is performed before reaming ?
boring Drilling Grooving Tapping

40 39. In following, the material removal is negligible
Drilling Shaping Boring Reaming

41 40. The end of drilled hole is
Flat Conical Circular Chamfering

42 41. The end of the bored hole is
Flat Conical Circular Chamfered

43 42. The following is a finishing operation
Drilling Reaming Tapping Parting

44 43. The recess of bolt heads or nut can be provided by
Drilling Boring Counter- boring Counter-sinking

45 Chamfering Counter-facing Counter-sinking Spot-sinking
44. The process of chamfering the entrance of a drilled hole is called as Chamfering Counter-facing Counter-sinking Spot-sinking

46 45. The Counter-sinking operation can be performed on
Grinding machine Lathe machine Drilling machine Both (b) & (c)

47 46. The recess for flat-head screw can be provided by __________
spot-facing Counter-facing Counter-sinking Chamfering

48 47. The drilling operation can be performed on
Milling machine Drilling machine Lathe machine Both (b) & (c)

49 48. The tool used for making internal threads is called as ___________
Lead screw Screw tool Tap Drill

50 Reaming Tapping Counter-sinking None of above
49. The process for making the internal threads in a drilled hole is called as _____________ Reaming Tapping Counter-sinking None of above

51 50. The following operation cannot be carried out on drilling machine
Internal threading External threading Boring Both (a) & (b)

52 51. in drilling machine, the chuck is mounted on
Spindle Column Base Work table

53 52. The material used for drill can be
Plain carbon steel Stainless steel Cast steel High speed steel

54 53. The end of drill hole is semi-circular Flat Conical Both (b) & (c)

55 54. The radial arm is presented on
Portable drilling machine Bench drilling machine Pillar drilling machine None of above

56 55. The grinding process gives
Good surface finish with substantial material removal Good surface finish with negligible material removal Good surface finish without material removal None of above

57 56. In cylindrical grinding machine
The grinding wheel & workpiece rotate in opposite direction The grinding wheel & workpiece rotate in same direction The grinding wheel is rotating & workpiece is stationary The grinding wheel & workpiece are stationary

58 57. The grinding wheel can be made up of ____________________
Tool steel Plain carbon steel Silicon carbide High speed steel

59 Cylindrical grinding machine Center less grinding machine
58. The grinding of rollers of bearing & piston pins can be carried out on Cylindrical grinding machine Center less grinding machine Surface grinding machine Special purpose grinding machine

60 59. In following machine, the material removal is minimum
Lathe Drilling Internal grinding Tool & cutter grinding

61 60. In cenerless grinding machine
There is two grinding wheels There is one grinding wheel & one regulating wheel Only one grinding wheel There is one grinding wheel & two regulating wheel

62 Electric motor Grinding wheel Regulating wheel Lead screw
61. In centerless grinding, the axial motion to the workpiece is provided by___________________ Electric motor Grinding wheel Regulating wheel Lead screw

63 62. In following machine the workpiece is stationary
Lathe Drilling grinding Both (b) & (c)

64 63. In centreless grinding ___________
The grinding wheel & regulating wheel rotate in opposite direction The grinding wheel & regulating wheel rotate in same direction The grinding wheel rotates & regulating wheel stationary None of above


Download ppt "MCQ."

Similar presentations


Ads by Google