1. Business Data Communications Chapter Two Physical Layer Fundamentals

2. Primary Learning Objectives Understand the general purpose of the physical layer Distinguish between analog and digital Signaling Describe circuit configurations and methods of data flow Identify characteristics of conducted and radiated Media Name and differentiate four types of multiplexing

3. Physical Layer Similar in both the OSI and TCP/IP models Specifies the physical characteristics of a network Stacked below the data link layer Transmits an “unformatted” data bit stream Has four key components: Signaling method Circuit configuration Transmission medium Devices used

4. Physical Layer Pin connector functions are an important physical layer responsibility

5. Signaling Methods -- 1 st Component of the Physical Layer Analog versus Digital Analog is continuous Digital is discrete Analog uses modulation techniques Amplitude, Frequency, Phase, for example Analog is measured in hertz Digital uses encoding schemes Manchester and Differential Manchester, for example Digital is measured in bps, or bits per second

6. Analog Signaling Methods Can take an infinite form Modulate a sine wave Can change a wave’s amplitude, frequency, or phase Amplitude affects the wave’s height or strength Frequency measures the waves per second Phase occurs when a wave changes direction Modulation is either Simple or Complex

7. Analog Signaling Methods

9. A hertz is a unit of frequency. A period is measured in seconds.

10. Analog Signaling Methods

11. Simple signal methods use: A choice of two amplitudes, or A choice of two frequencies, or A single phase change A simple signal method has the same symbol and bit rate

12. Analog Signaling Methods A complex signal method occurs when the bit rate and the symbol rate are not the same: A symbol, or baud, rate can represent more than one bit per time period When more then one bit is represented within a single symbol, then the symbol and bit rates differ Complex signal methods require that more than one bit be represented per symbol Complex signal methods combine different amplitudes, frequencies, or phases, or some combination of these

13. Analog Signaling Methods

14. Analog Bandwidth Analog bandwidth is measured in hertz The bandwidth measurement is the difference between a given analog’s lowest and highest frequencies The spectrum consists of the entire range of frequencies, from lowest to highest

15. Analog Bandwidth and Frequency Spectrum Example

16. Digital Signaling Methods Are discrete, not continuous Take the value of a binary 0 or binary 1 Make use of encoding schemes such as: Manchester Ethernet Differential Manchester Token Ring

17. Digital Signaling Methods

18. Make use of a “bit interval”, the time required to send a single bit The sender and receiver can use this bit interval to clock their transmission with each other With the bit interval as a clocking mechanism The sender and receiver can synchronize their transmissions However, self-clocking mechanisms are more efficient A bit rate is also associated with a digital signaling method The bit rate is the number of bit intervals per second, or bps

19. Digital Bandwidth Digital bandwidth is typically expressed in bits per second (bps) Digital bandwidth is determined using the bit interval and the bit rate Assuming we have a digital signal with a bit interval of 60 microseconds, what is its bandwidth? The formula is expressed as: bps = 1 / (60 * 10 -6 ), or approximately 16.6 Kbps (thousands of bits per second)

20. Transmitting Encoded Data The bits that represent encoded characters can be transmitted simultaneously (parallel transmission) or one at time (serial transmission) Serial transmission is more widely used than parallel transmission for data communication Parallel transmission is used for communication between components within a computer In serial transmission, encoded characters can either be transmitted one at a time (asynchronous transmission) or in blocks (synchronous transmission) – UART provides the interface between parallel transmission within the computer and serial transmission ports. It also plays a key role in formatting encoded characters for asynchronous transmission

21. Digital Signaling Methods

22. Circuit Configuration -- 2 nd Component of the Physical Layer Two major categories Point-to-point Multipoint Point-to-point circuits are dedicated links between two communicating devices Multipoint circuits are shared among several communicating devices Either could be appropriate based on network need

23. Point-to-point Circuit

24. Multipoint or Multidrop Circuit

25. Transmission Medium -- 3 rd Component of the Physical Layer Two major categories Conducted Radiated Conducted – Makes use of cables Twisted wire pair, coaxial cable, fiber optic Radiated – is “In the Air” Terrestrial microwave, satellite, radio, infrared

26. Conducted Media Use Cable An example of category 5, unshielded twisted wire pair An example of a coaxial cable, with its layered sheathing

27. Conducted Media Use Cable Single mode fiber Cable with Connectors Fiber cores are measured in microns Another type of fiber is multimode Fiber is composed of either glass or plastic strands

28. Radiated Media, Signals “in the air”

29. Transmission Medium Considerations Cost Bandwidth Security Transmission Impairment Distance

30. Transmission Medium Impairment Considerations Attenuation Cross talk Distortion Environmental factors Rain, fog, snow, cloud cover, electrical or magnetic storms Of the various media, fiber optic is the least susceptible to impairment, and the most secure But also very expensive!

31. Comparison of Various Media Type of MediumSecurityTransmission Distance CostError Potential Difficulty of Installation Twisted Wire PairModerateShortLowModerateLow Coaxial CableModerateShortModerateLow Fiber OpticHighModerate to LongHighVery LowHigh RadioLowShortLowModerate Terrestrial MicrowaveLowLongModerateLow to Moderate SatelliteLowLongModerateLow to Moderate

32. Devices at the Physical Layer -- 4th Component of the Physical Layer Hubs or Repeaters Modems Codecs Multiplexers Cabling Tools (Not devices, but still important)

33. Devices at the Physical Layer -- 4th Component of the Physical Layer

34. Multiplexing Allows slower-speed circuit devices to share a single high-speed circuit In many cases, individual devices do not need their own high-speed circuit Type of multiplexing include: Frequency division Time division Statistical time division Wavelength division

35. Frequency Division Multiplexing A single high-speed circuit with multiple channel frequencies The circuit is analog Bandwidth is measured in hertz Data transmitted via channels Viewed as horizontal Makes use of guardbands as overhead

36. Frequency Division Multiplexing

37. Time Division Multiplexing A single high-speed circuit carrying multiple frames Time slots may only be used by specifically allocated devices The circuit is digital Bandwidth is measured in bits per second (bps) Data transmitted via frames Viewed as vertical Unused time slots create overhead

38. Time Division Multiplexing

39. Statistical Time Division Multiplexing A single high-speed circuit carrying multiple frames Time slots can be allocated to devices as needed Time slots must carry addressing The circuit is digital Bandwidth is measured in bits per second Data transmitted via frames Viewed as vertical, not horizontal Addressing of time slots creates overhead

40. Statistical Time Division Multiplexing

41. Wavelength Division Multiplexing Makes use of fiber optics Operates in a manner somewhat similar to the way that frequency division multiplexing is used with copper Uses lasers to transmit different frequencies of light through the same fiber optic cable At the sending end, narrow bands of light are combined into a wider band The wider band is the high-speed circuit At the receiving end, the signals are separated

42. Error Sources There are many sources of data communication transmission errors including: Signal attenuation Impulse noise Crosstalk Echo Phase jitter Envelope delay distortion White noise Electromagnetic interference (EMI)

43. Error Impacts Errors cause bits to be changed (corrupted) during transmission; without error-detection mechanisms, erroneous data could be received and used in application processing Figure 6-32 illustrates a transmission error caused by noise Table 6-8 indicates that longer impulse noises can corrupt multiple bits, especially as transmission speed increases

44. Figure 6-32

45. Table 6-8

46. Error Prevention Error prevention approaches used in data communications include: Line conditioning Adaptive protocols (such as adaptive line probing, fallback, adaptive size packet assembly) Shielding Repeaters and amplifiers Better equipment Flow control RTS/CTS XON/OFF

47. Error Detection Approaches Error detection processes vary in complexity and robustness. They include: Parity checking (see Table 6-9) Longitudinal redundancy checks (LRC) – see Table 6-10 Checksums Cyclical redundancy checks (most widely used and robust) CRC-12 CRC-16 CRC-32 Sequence checks Other approaches include check digits, hash totals, byte counts, and character echoing

48. Table 6-9

49. Table 6-10

50. Error Recovery Automatic repeat request (ARQ) is the most widely used error- recovery approach in data communications. In this approach, the receiver requests retransmission if an error occurs. There are three major kinds of ARQ: Discrete ARQ (aka stop-and-wait ARQ). Sender waits for an ACK or NAK before transmitting another packet Continuous ARQ (aka go-back-N ARQ). Sender keeps transmitting until a NAK is returned; sender retransmits that packet and all others after it Selective ARQ. Sender only retransmits packets with errors Forward error correction codes involve sending additional redundant information with the data to enable receivers to correct some of the errors they detect. Hamming code and Trellis Coded Modulation are examples Error control/recovery standards include MNP Class 4, V.42, and LAP-M (see Table 6-12)

51. In Summary The physical layer: In the OSI and TCP/IP models is similar Is essential for transporting of data bits from sender to receiver Has circuits that are Conducted or Radiated Passes its unformatted data bit stream up to the Data Link Layer