Presentation is loading. Please wait.

Presentation is loading. Please wait.

AFC Module Meeting Friday - May 21, 2004 Report on the Window burst test Edgar Black IIT.

Published by Modified over 9 years ago

Similar presentations

Presentation on theme: "AFC Module Meeting Friday - May 21, 2004 Report on the Window burst test Edgar Black IIT."— Presentation transcript:

1 AFC Module Meeting Friday - May 21, 2004 Report on the Window burst test Edgar Black IIT

2 MTA Absorber Design Progress This windows are of a nominal 21cm diameter The diameter was selected to fit on the forced flow absorber inside the 40cm. diameter magnet bore (lab G magnet) The design called for 25psi MOP and rupture up to 100psi The bellow type new configuration was aimed to achieve a minimum of 105 micron thickness at the center Data from the burst test on this window will be used to verify the window design parameters for MICE

3 Fabricated window design details

4 Window profile parameters

5 Manifold construction detail

6 Back plate for pressure test

7 Receiving window inspection CMC report (partial sample) the holes and the plane on right side. Bolt circle constructed of points of intersection between DIM BOLT CIRCLE OF HOLES ON RT SIDE= LOCATION OF CIRCLE B.C.RT SIDE UNITS=MM AX MEAS X 0.00000 Y 0.00000 Z 0.00000 D 218.02053 RN 0.04067 Holes measured as cylinders, starting with the hole at 90 deg and going anti-clockwise. Measurements shown are Polar Radius, Polar Angle, Diameter and Vectors I,J,K. DIM HOLE AT 90 DEG= LOCATION OF CYLINDER RT 90 HOLE UNITS=MM AX MEAS PR 108.98744 PA 89.98625 D 3.21533 V -0.00063 -0.00067 1.00000 0.00000 DIM RND1= ROUNDNESS OF CYLINDER RT 90 HOLE UNITS=MM AX MEAS M 0.10550 DIM HOLE AT 150 DEG= LOCATION OF CYLINDER CYL1 UNITS=MM AX MEAS

8 Measurements results Photogrametry technique give the minimum thickness to be 190 microns Gauged thickness on the burst window material at the center measured 101 microns The above measurements included 15 micron total of the material (spray paint) coating both sides of the window Donald Summers reported a central thickness of 117 microns (no paint)

9 Burst test No fatal events as predicted, a safety analysis was submitted before the test for approval Pressure was apply to the window/plate volume on increments of 5psig A leak developed over the elastomer gasket at 133psig Changed the gasket 2.5mm instead of.8mm diameter plus vacuum grease Repeated test, burs pressure at 144psig

Download ppt "AFC Module Meeting Friday - May 21, 2004 Report on the Window burst test Edgar Black IIT."

Similar presentations

. . CONSTRUCTION OF A RIGHT TRIANGLE IF THE ONE ANGLE OF A TRIANGLE IS 90,IT IS CALLED RIGHT TRIANGLE.

. . CONSTRUCTION OF A RIGHT TRIANGLE IF THE ONE ANGLE OF A TRIANGLE IS 90,IT IS CALLED RIGHT TRIANGLE.
Volume of Cones and Pyramids

Volume of Cones and Pyramids
Vacuum Vessel Production Readiness Review

Vacuum Vessel Production Readiness Review
MICE RF Cavity Design and Fabrication Update Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 27, 2004.

MICE RF Cavity Design and Fabrication Update Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 27, 2004.
A simple clamping device for the Solid absorber Wing Lau, Oxford.

A simple clamping device for the Solid absorber Wing Lau, Oxford.
Agreement on scope of supply and extent of interface among different suppliers of the AFC module This talk covers the scope of supply on the Absorber Focus.

Agreement on scope of supply and extent of interface among different suppliers of the AFC module This talk covers the scope of supply on the Absorber Focus.
MICE RF Cavity Measurements Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory March 26, 2010 University of California, Riverside,

MICE RF Cavity Measurements Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory March 26, 2010 University of California, Riverside,
Status of the 201 MHz Cavity and Coupling Coil Module Steve Virostek Lawrence Berkeley National Laboratory MICE Video Conference March 10, 2004.

Status of the 201 MHz Cavity and Coupling Coil Module Steve Virostek Lawrence Berkeley National Laboratory MICE Video Conference March 10, 2004.
Installation Issues Steve Virostek Lawrence Berkeley National Lab MICE CM23 at ICST, Harbin January 13, 2009.

Installation Issues Steve Virostek Lawrence Berkeley National Lab MICE CM23 at ICST, Harbin January 13, 2009.
The issue: A non-standard thin window design  No closed form expression for maximum stress vs. volume pressure  FEA (finite element analysis): geometry.

The issue: A non-standard thin window design  No closed form expression for maximum stress vs. volume pressure  FEA (finite element analysis): geometry.
Module Vessel Connection Concept Steve Virostek Lawrence Berkeley National Laboratory AFC Module Meeting April 23, 2004.

Module Vessel Connection Concept Steve Virostek Lawrence Berkeley National Laboratory AFC Module Meeting April 23, 2004.
MICE COLLABORATION MEETING CERN March 29-April 1, 2004 Detector/Focus Coil module interface details P. Fabbricatore INFN-Genova Detector/Focus Coil module.

MICE COLLABORATION MEETING CERN March 29-April 1, 2004 Detector/Focus Coil module interface details P. Fabbricatore INFN-Genova Detector/Focus Coil module.
Module Connection and Support Arrangement Steve Virostek Lawrence Berkeley National Laboratory AFC Module Meeting May 21, 2004.

Module Connection and Support Arrangement Steve Virostek Lawrence Berkeley National Laboratory AFC Module Meeting May 21, 2004.
The structural and Fluid flow analyses of the Hydrogen Absorber Window for the Muon Cooling collaboration project Presented at the MICE meeting at IIT.

The structural and Fluid flow analyses of the Hydrogen Absorber Window for the Muon Cooling collaboration project Presented at the MICE meeting at IIT.
5/7/2003Edgar L. Black IIT MICE Meeting at Columbia University Hydrogen/Focus Module Components assembly Details concept June 13,2003.

5/7/2003Edgar L. Black IIT MICE Meeting at Columbia University Hydrogen/Focus Module Components assembly Details concept June 13,2003.
MICE modules interface proposal FAC module Phone meeting Edgar Black IIT 2/13/2004.

MICE modules interface proposal FAC module Phone meeting Edgar Black IIT 2/13/2004.
Update on Be Wall Cavity Steve Virostek Lawrence Berkeley National Lab MTA RF Workshop November 15, 2010.

Update on Be Wall Cavity Steve Virostek Lawrence Berkeley National Lab MTA RF Workshop November 15, 2010.
MICE Absorber and Test Cryostat Shigeru Ishimoto KEK MICE AFC Module Phone Conference (March 12, 2004) (1) MICE Absorber Test Process (2) MICE Absorber.

MICE Absorber and Test Cryostat Shigeru Ishimoto KEK MICE AFC Module Phone Conference (March 12, 2004) (1) MICE Absorber Test Process (2) MICE Absorber.
11/26/2002Edgar L Black IIT MICE Video Conference November 27, 2002 Summary of safety implementation for proposal.

11/26/2002Edgar L Black IIT MICE Video Conference November 27, 2002 Summary of safety implementation for proposal.
Non-welded Window Option Edgar L. Black IIT August 15,2003.

Non-welded Window Option Edgar L. Black IIT August 15,2003.

Similar presentations

Ads by Google