1. Lec 5: Thermodynamic properties, Pvt behavior

2. For next time: Outline: Important points: Read: § 3-5 HW 3 due Sept 17
Buoyancy and stability
Pure substances and processes
Property diagrams for pure substances
Important points:
How to calculate point of action of hydrostatic load
The general shape of the property diagrams
How to solve problems using the property diagrams

3. Properties - Introduction
We have discussed extensive properties such as U, m, and V (for volume) which depend on the size or extent of a system, and
Intensive properties such as u, v, T, and P which are independent of system extent (engineers are ambivalent about nomenclature for pressure, sometimes using p and P interchangeably)

4. Important questions...
How many properties are needed to define the state of a system?
How do we obtain those properties?

5. For a simple system,
We may write: p = p(v,T)
or perhaps: v = v(p,T).

6. Pure
Pure means “…of uniform and invariable chemical composition (but more than one molecular type is allowed).” This allows a single phase of air to be a pure substance.
All our substances will be pure. We will drop the use of the word. When we refer to a simple system we mean one filled with a pure substance--a simple, pure system.

7. For a simple, pure substance
y1 = f(y2,y3), or
p = p(v,T), v = v(p,T) and T = T(p,v)
What do these equations define, in space?
Equations used to relate properties are called “equations of state”

8. Ideal gas “law” is a simple equation of state
Ru = universal gas constant
m = mass
n = number of moles
M = molar mass or molecular weight

9. Behavior of real substances
Lets consider substances that do not obey the perfect gas law
certainly not as a solid
certainly not as a liquid
sometimes not very well as a gas

10. Phase Change Process of a Pure Substance
liquid
liquid
liq/vap
P=1 atm
P=1 atm
P=1 atm
T=20°C
T=100°C
T=100°C
P=1 atm
P=1 atm
T=250°C
T=100°C
vapor
vapor

11. Consider a constant pressure process (of water)

12. T-v Diagram

14. You should be able to discuss characteristics of the following:
Liquid to liquid/vapor to vapor transition (begin with a constant pressure process).
Single phase regions--liquid, vapor, solid.
Two-phase regions--liquid/vapor and solid/vapor.
Melting--solid to liquid (freezing)
vaporization--liquid to vapor (liquefaction)
sublimation--solid to vapor

16. Notice the triple-state line
Notice the triple-state line. Along this line all three states exist in equilibrium
For water, the triple point is at K ( F) and kPa ( psia).

17. Vapor Dome - region encompassing the two-phase, vapor-liquid equilibrium region
Saturated liquid line
Saturated vapor line

18. Critical Point
Point at which the saturated vapor and saturated liquid lines coincide.
If T  Tc or P  Pc there is no clear distinction between the superheated vapor region and the compressed liquid region.
Substances in this region are sometimes known as “fluids” rather than as vapors or liquids.
By convention, if P  Pc, and T  Tc we refer to the fluid as superheated. If P  Pc, and T < Tc we refer to the fluid as a subcooled or compressed liquid.

19. Phase Diagram (PT-coordinates)

20. Constant Temperature Process
Compressed Liquid
Superheated Vapor

21. Constant Pressure Process
Subcooled Liquid
Superheated Vapor

23. Sat. Liquid Line Sat. Vapor Line Superheated Region Subcooled Region
Critical Point
Sat. Liquid Line
Sat. Vapor Line
Superheated Region
Subcooled Region
Saturation Region

25. Saturation temperature
Temperature at which a phase change takes place at a given pressure.

26. Saturation pressure
Pressure at which a phase change takes place at a given temperature.

27. TEAMPLAY
Discuss what happens when water boils on the stove at your residence. Start with a pan of water at 70 F, 1 atm pressure. Q
Continued on next slide.

28. TEAMPLAY (CONTINUED)
What is the pressure at various times during the entire process?
Does the temperature of the water change?
If the vapor (steam) were contained in an elastic container, what would happen as heat continued to be added after all the liquid disappeared.
Sketch pV and TV diagrams.

29. Saturation properties
Along the saturated liquid line, properties are identified by the subscript “f”
Along the saturated vapor line, properties are identified by the subscript “g”
Both sets of properties can be found in the temperature and pressure tables in your book’s appendices.
Both tables give the same data.
There are different tables for different substances.

30. Temperature table (also known as a saturation table)

31. Pressure table (also known as a saturation table)

32. [Two properties are not independent in the vapor dome (the two-phase region)]
The temperature and pressure are uniquely related. Knowing a T defines the P and vice versa.

33. TEAMPLAY
Find, for Refrigerant 134a, the following properties: the saturation pressure at a saturation temperature of -10 F.
and find for the same substance the saturation temperature at a pressure of 0.06 MPa.
Make sure everyone in your group understands how to do this.