1. PC Peripherals for Technicians
Mar 1998
PC Peripherals for Technicians
Chapter Video Subsystem Overview
Systems Manufacturing Training and Employee Development
Copyright © 1998 Intel Corp.
Rev. 2.0 Sys MFG Training/Employee Development

2. Video Section Overview: Ch 3.1 - 3.3
PC Peripherals for Technicians
Mar 1998
Video Section Overview: Ch
3.1 - Overview of displaying images in a Graphics System
3.1 - Block diagram of Video Subsystem & port connector
3.2 - Video Display Modes in a Graphics System
3.2 - Text Mode Video Buffer data format & character fonts.
3.2 - The attribute byte & the palette registers
3.2 - Color generation using the Video DAC
3.3 - The Graphics Mode Video Buffer data format.
3.3 - Characteristics of VGA Mode 12 hex & Mode 13 hex
3.3 - Graphics Modes Color generation & Character fonts
3.3 - SVGA, VESA & extended video modes.
3.3 - Video Subsystem initialization & troubleshooting.
Rev. 2.0 Sys MFG Training/Employee Development

3. Video Subsystem Overview
PC Peripherals for Technicians
Mar 1998
Video Subsystem Overview
OBJECTIVES: At the end of this section, the student will be able to do the following:
Discuss the interactions in a Graphics System
Name the functional elements of a Video Adapter
Explain how images are displayed on a CRT
Discuss a block diagram of the Video Subsystem
Describe Video Subsystem port connectors
Rev. 2.0 Sys MFG Training/Employee Development

4. PC Peripherals for Technicians
Mar 1998
Video Subsystems
This section focuses on the VGA standard which was introduced by IBM in 1987 and is commonly used today.
This information is generic in nature and may not apply in some video modes or adapter configurations.
Register functions used primarily by programmers and color/ mono differences are beyond the scope of this course.
There are several standard Graphics Adapters.
MDA (Monochrome Display Adapter)
CGA (Color Graphics Adapter)
EGA (Enhanced Graphics Adapter)
VGA (Video Graphics Array) - Focus of this course
SVGA (Super Video Graphics Array)
Limited backward compatibility exists--implies that software for simpler adapters works on the more complex adapters.
Rev. 2.0 Sys MFG Training/Employee Development

5. PC Peripherals for Technicians
Mar 1998
Video Subsystems
The PC Video Graphics Controller is responsible for producing the image that is displayed on the screen.
This hardware can be located on the System Board or on an add in card called a Graphics Adapter or Display Adapter that plugs into an expansion slot (PCI, ISA, etc).
The PC Video Subsystem contains a block of dedicated memory called the Video Buffer, Video Memory, Display Memory or Video RAM.
This Display Memory holds the text or graphics information to be displayed on the screen.
Stores a mirror of the screen picture (digital data).
A primary function of the VGA Controller is to serialize the data in it’s display memory and to mix this stream of data with synchronizing signals that control the video display.
Rev. 2.0 Sys MFG Training/Employee Development

6. Interactions in a Graphics System
PC Peripherals for Technicians
Mar 1998
Interactions in a Graphics System
An O/S (DOS, Windows, etc.) and/or Application program (word processor, game, etc.) updates information on the screen using the Video BIOS or a Video Device Driver.
An installable Device Driver is a program that works with the O/S to translate commands that control a piece of hardware, typically for extended functions not supported by standard hardware.
SOFTWARE
Operating System
Applications
BIOS / Graphics Drivers
HARDWARE
Microprocessor
PC RAM / ROM
Video Controller
Video
Memory
Graphics
Subsystem
DAC
DISPLAY
Software Interrupt 10h is used for Video BIOS routines
Rev. 2.0 Sys MFG Training/Employee Development

7. Interactions in a Graphics System
PC Peripherals for Technicians
Mar 1998
Interactions in a Graphics System
A special section of display memory called the Video Buffer (separate from main system memory) stores data that will appear on the screen.
This memory is accessed via the Video Subsystem by the CPU as well as the Video Controller, permitting a program to change the display screen by updating the contents of the display memory.
The video is commonly displayed on a Monitor which converts the synchronizing and video signals from the graphics sub-system into the proper form for display use.
Digital signals are used internally by the Controller, and VGA and later uses analog signals to drive the Display.
The Digital to Analog Converter (DAC) converts the color information supplied by the VGA chip to analog voltages for the red, green, and blue gun outputs to the monitor.
Rev. 2.0 Sys MFG Training/Employee Development

8. PC Peripherals for Technicians
Mar 1998
Display Adapter Functional Elements: Text Mode
Dot Stream
To Monitor A
41 07
Video RAM
ASCII
Char
Code
41h h
ATTR
Info
(colors)
Video Controller
Video
Signal
Generator
CRT
Controller
Alphanumeric
Character
Attribute
Decoder
Color &
Intensity
Dot Pattern
Horiz & Vert
Timing
BUS
Interface
Microprocessor
NOTE: The Video Signal Gen & Alphanumeric Char. Gen functions are performed by more than one of the programmable components in the VGA block diagram discussed later in this chapter.
Rev. 2.0 Sys MFG Training/Employee Development

9. Display Adapter Functional Elements: Text Mode
PC Peripherals for Technicians
Mar 1998
Display Adapter Functional Elements: Text Mode
The System or Bus Interface :
Decodes memory addresses to Video Memory or I/O addresses to the VGA registers.
The Cathode Ray Tube Controller (CRTC):
Generates the horizontal and vertical timing signals that control the path and duration of the electron beam sweeping the inner surface of the CRT.
Display memory
The Video Buffer contains the information to be displayed on the screen & is effectively a large shift register sending a serial data stream to the monitor.
Alphanumeric Character Generation circuitry:
Translates the ASCII value of a character stored in the video buffer into a matrix of dots to display on the screen.
Rev. 2.0 Sys MFG Training/Employee Development

10. Display Adapter Functional Elements: Text Mode
PC Peripherals for Technicians
Mar 1998
Display Adapter Functional Elements: Text Mode
The Attribute Decoder:
Controls the color and brightness of the signals sent to the monitor.
Video Signal Generator:
Outputs the signals that control what appears on the screen.
Horiz sync (to 90 KHz)
Vert sync ( Hz)
Three possible kinds of video signals are:
Digital (CGA, EGA) - Digital RGB monitors accept TTL level signals for red, green, or blue on separate lines.
Analog (VGA) - Analog RGB monitors accept 0-0.7V analog signals for red, green and blue on separate lines.
Composite (also used for TV) - The red, green, and blue are combined by the video subsystem and separated by the monitor.
Rev. 2.0 Sys MFG Training/Employee Development

11. Displaying Images: The CRT
PC Peripherals for Technicians
Mar 1998
Displaying Images: The CRT
Heating
filament
Horizontal
deflection
coils/plates
Electron beam
Phosphor
Coating
Interior metallic coating at
high positive voltage
Vertical deflection
Focusing
system
Control
grid
(Intensity)
Cathode
Cathode Ray Tube (CRT)
Rev. 2.0 Sys MFG Training/Employee Development

12. Displaying Images: The CRT
PC Peripherals for Technicians
Mar 1998
Displaying Images: The CRT
The rear part of the CRT contains a cathode that emits an electron beam when heated.
A color monitor has three adjacent electron beams (Red, Green, & Blue) which can be regarded as a single beam.
The front surface of a computer monitor is actually the end of a large CRT.
In a color monitor, there are three adjacent phosphor dots (a triad) called a PEL or PIXEL (Picture Element) laid out in horizontal scan lines.
Dot Pitch indicates the distance between triads (e.g mm) and is a measure of the resolution of the monitor.
Typical ranges is 0.15 mm to 0.40 mm
When the intensity modulated electron beam strikes the phosphor coated inner surface of the CRT, it changes the brightness of the CRT’s glow.
Rev. 2.0 Sys MFG Training/Employee Development

13. Displaying Images: The CRT
PC Peripherals for Technicians
Mar 1998
Displaying Images: The CRT
The CRT’s electron beam sweeps across the screen in a fixed path from left to right (Horizontal) and top to bottom (Vertical).
These lines are continually scanned many times a second producing a uniform pattern of closely spaced horizontal lines (called a raster) which covers the entire screen.
This is fundamentally the same way that a TV operates.
The CRT image must be redrawn continuously because it will remain visible for only a few milliseconds depending on the persistence of the phosphor.
With “additive” mixing of the 3 primary colors, all known colors can be generated
Mixing equal parts of red, green & blue produces shades of white light.
Rev. 2.0 Sys MFG Training/Employee Development

14. Non-Interlaced and Interlaced Displays
PC Peripherals for Technicians
Mar 1998
Non-Interlaced and Interlaced Displays
Displays are either interlaced or non-interlaced.
In an interlaced graphics system, it takes 2 fields (1 odd, 1 even) to display one complete screen (called a frame)
Interlaced mode is used when the monitor cannot keep up with the data rates required by the video system--used for the first 1024x768 displays.
A non-interlaced display has an entire frame displayed each screen refresh--every line is updated every frame.
Non-interlaced displays produce a more pleasing screen image (less flicker) than interlaced displays.
Quality monitors feature non-interlacing at all resolutions.
Some monitors can only work in non-interlaced mode up to a maximum pixel addressability (e.g. 800x600) above which they revert to interlaced mode.
Rev. 2.0 Sys MFG Training/Employee Development

15. Displaying Images: Non-Interlaced mode
PC Peripherals for Technicians
Mar 1998
Displaying Images: Non-Interlaced mode
Horizontal Retrace:
Repositions the beam back to the start of the next horizontal scan line.
Vertical: Approx
70 cycles/sec
for Text Mode 3
Horiz: Approx
31.5K cycles/sec
Scan Line
Vertical Retrace:
Repositions the beam back to the top left corner
voltage
Vertical Deflection
Time
Horizontal Deflection
Note:
Angle of scan line is exaggerated
Rev. 2.0 Sys MFG Training/Employee Development

16. Displaying Images: Interlaced mode
PC Peripherals for Technicians
Mar 1998
Displaying Images: Interlaced mode
Horizontal Retrace
Note:
Angle of scan line is exaggerated
Vertical Retrace
Odd Scan Line
Even Scan Line
Time
voltage
Vertical Deflection
Horizontal Deflection
The first field consists of only the odd numbered line.
The next field consists of only the even numbered lines.
Rev. 2.0 Sys MFG Training/Employee Development

17. Displaying Images: Interlaced mode
PC Peripherals for Technicians
Mar 1998
Displaying Images: Interlaced mode
Interlacing is the way that a television operates.
The TV rate is 2:1 interlace - 60 fields/sec; 30 frames/sec
A 30 frame-per-second rate would noticeably flicker, while the effective 60 frame-per-second rate does not.
The human eye recognizes the the alternate scanlines as one image because it can’t resolve the flickering of images refreshed more than 50 time per second.
The advantage of interlacing is that the frame rate (and the video B/W) is half of what would be required to display this same resolution in non-interlaced mode.
Interlacing results in the ability to display a resolution that would be impossible for hardware in non-interlaced mode.
Interlacing enables a monitor to provide more resolution inexpensively.
Rev. 2.0 Sys MFG Training/Employee Development

18. Video Data Format Overview
PC Peripherals for Technicians
Mar 1998
Video Data Format Overview
Video Display Modes: Video subsystems operate in multiple display modes which control certain aspects of the video operation.
Text OR Graphics:
Text modes display alphanumeric characters only.
Graphics modes are bit-mapped (All Points Addressable)
Screen Resolution: # of pixels vertically & horizontally.
e.g. 720 x 400; 640 x 480; x 768; x 1024
Level of sharpness of image.
Number of colors available: Typically 16 to 16 million
Note: The initial video mode is an 80-column Text mode (03h) set by the ROM BIOS during POST.
Rev. 2.0 Sys MFG Training/Employee Development

19. Video Data Format Overview
PC Peripherals for Technicians
Mar 1998
Video Data Format Overview
The information written to the video buffer by the microprocessor is represented on the screen as a pattern of illuminated dots called pixels.
The microprocessor writes information to the video hardware’s display buffer in either alphanumeric or graphics format.
Each location on the video screen maps to a location in the display RAM.
Discussed in more detail in a subsequent chapter.
The first location of the display buffer maps to the top, leftmost point on the screen.
As memory addresses increase, the screen location move from left to right & top to bottom.
Rev. 2.0 Sys MFG Training/Employee Development

20. Video Data Format Overview
PC Peripherals for Technicians
Mar 1998
Video Data Format Overview
Alphanumeric format: (Text Mode)
Discussed in more detail in a subsequent chapter.
The microprocessor writes each symbol (letter, number, etc) as a series of 2 bytes (character & attribute) into the Video Memory.
The first byte represents the character’s ASCII value
The second byte represents the character’s attribute (i.e. color, foreground/background, blinking, intensity)
Video hardware translates the character & attribute bytes to the necessary series of dots.
Characters are painted on the screen in a matrix of dots called a character box or character cell.
Rev. 2.0 Sys MFG Training/Employee Development

21. Video Data Format Overview
PC Peripherals for Technicians
Mar 1998
Video Data Format Overview
Mapping from the display
memory to the screen.
Segment B800 - Text Mode
Seg:Offset
B800:0 ASCII
B800:2
B800:1 Attrib.
B800:3
B800:4
B800:5
B800:6
B800:7
41h
42h
43h
07h
Alphanumeric format
(Text Mode) A B C
SCREEN
Rev. 2.0 Sys MFG Training/Employee Development

22. Video Data Format Overview
PC Peripherals for Technicians
Mar 1998
Video Data Format Overview
Graphics Mode format:
Discussed in more detail in a subsequent chapter.
Also known as All Points Addressable (A.P.A.)
The microprocessor writes the individual color value of each pixel to be painted on the screen.
All pixels can be controlled independently to draw graphics objects (as opposed to Text Mode, in which only a pre-defined set of characters can be displayed.
The microprocessor must address the display buffer as a memory map of a series of bits (bytes for Text mode).
The Video hardware generates the color & control signals necessary to illuminate the dot at the correct location on the screen.
Rev. 2.0 Sys MFG Training/Employee Development

23. Video Subsystem Block Diagram
PC Peripherals for Technicians
Mar 1998
Video Subsystem Block Diagram
The following block diagram will introduce the typical functions of a VGA Video Controller.
The following is a generic description to show the relationship between components of the VGA Video Controller.
Note that many of the components of the video controller interact and this can be represented with different interconnect configurations.
You may see the following blocks grouped and/or connected in different ways, depending on the vendor and the level of detail shown.
Rev. 2.0 Sys MFG Training/Employee Development

24. Video Subsystem Block Diagram
PC Peripherals for Technicians
Mar 1998
Video Subsystem Block Diagram
A video display adapter contains the following basic elements (usually implemented in an ASIC):
Host Interface
Clock Generator (Frequency Synthesizer)
CRT Controller (CRTC): [Ports 3D4, 3D5]
Memory Sequencer: [Ports 3C4, 3C5]
Display Memory (Video Buffer) [A000:0 - B000:FFFF]
Graphics Controller: [Ports 3CE, 3CF]
Attribute Controller (Palette) : [Ports 3C0, 3C1]
DAC: [3C7 (PEL Addr Rd); 3C8 (PEL Addr Wr); 3C9 (Pixel Data)]
Video BIOS (Not implemented in ASIC)
Note: Point & Shoot is used to access registers.
Sometimes shown as 3?4 (i.e. 3D4=color, 3B4= mono).
Rev. 2.0 Sys MFG Training/Employee Development

25. Video Subsystem Block Diagram
PC Peripherals for Technicians
Mar 1998
Video Subsystem Block Diagram
Clock
SYNTH
Horizontal Timing
Vertical Timing
Dot Stream
To Monitor
CRT
CRT Ctlr
&
Memory
Sequencer
Optional
FIFO
Video
Graphics
Controller
Attribute
(Palette)
System
Bus
Interface
Control
Addr
Data
Ctrl
Feature
Connector
Dot Clock
Mem
DAC
(Lookup Table) R G B
Rev. 2.0 Sys MFG Training/Employee Development

26. Block Diagram: Sys I/F & Clock Gen.
PC Peripherals for Technicians
Mar 1998
Block Diagram: Sys I/F & Clock Gen.
The System Interface:
Decodes memory addresses to the Video Memory OR I/O addresses to the Video Controller registers.
Generates handshake signals to the system CPU.
An Optional Write Buffer isolates the CPU from the display memory (If Write Buffer is full, wait states are inserted)
The Frequency Synthesizer:
Generates frequencies from a fixed source (e.g MHz).
Programmed to generate the VCLK & MCLK.
Video (Pixel, Dot) Clock: VCLK range (25-135MHz)
This determines the “Video Bandwidth”
MCLK (Memory Clock): MCLK range (35-80 MHz)
Used by the Memory Sequencer
Rev. 2.0 Sys MFG Training/Employee Development

27. PC Peripherals for Technicians
Mar 1998
Block Diagram: CRTC
The Cathode Ray Tube Controller maintains screen refresh functions for the various display modes.
Generates Horiz. & Vert. timing signals for the monitor.
These control the path and duration of the electron beam sweeping the inner surface of the CRT.
Generates addresses for the DRAM Display Buffer.
The CRTC selects the portion of the video buffer to be displayed on the screen.
Addresses are sent to the Memory Sequencer.
The CRTC synchronizes the Video Buffer address counter with the Horizontal and Vertical timing signals.
Controls the size & location of the text mode cursor & generates the Cursor & underline timing signals
Rev. 2.0 Sys MFG Training/Employee Development

28. Block Diagram: Sequencer
PC Peripherals for Technicians
Mar 1998
Block Diagram: Sequencer
The Memory Sequencer consists of a Memory Controller & Memory Arbitrator.
The Memory Controller:
Generates the signals & addresses for accessing display memory and provides mapping of the Video Memory.
The Memory Arbitrator:
Ensures that the necessary screen refresh & DRAM refresh cycles are executed.
The Video Buffer may be accessed by 3 resources:
The Video Output Circuitry: Stream of data to redraw display (~ 80% of mem accesses)
The Host computer: Accesses the memory to update the screen.
The DRAM Refresh circuitry
Rev. 2.0 Sys MFG Training/Employee Development

29. Block Diagram: Display Memory
PC Peripherals for Technicians
Mar 1998
Block Diagram: Display Memory
The Video Buffer is a block of RAM that exists on the adapter but is mapped into the microprocessor’s address space.
The Video Buffer contains the information to be displayed on the screen.
The video circuitry refreshes the screen by continually and repeatedly reading the data in the video RAM.
Address map range: A000: B000:FFFF for VGA
The actual size of the Video Buffer varies with video subsystem: 64KB to 4 MB (or more).
Most PC subsystems have enough DRAM to hold more than one screen of displayable data, so only part of the Video Buffer is visible on the screen.
Rev. 2.0 Sys MFG Training/Employee Development

30. Block Diagram: Display Memory
PC Peripherals for Technicians
Mar 1998
Block Diagram: Display Memory
Types of memory chips commonly used:
DRAM is the most popular - (Fast Page or EDO)
VRAM (Video RAM) - Dual-ported RAM
The adapter can fetch the contents of memory for display at the same time that new data is being put into memory.
The CPU use the parallel port for random reads & writes
The adapter updates the display by reading the serial port.
Typically costs twice as much as DRAM.
WRAM (Short for Window RAM)
Similar to VRAM, but has faster performance at less cost.
SGRAM (Synchronous Graphic Random Access Memory
Can synchronize itself with the CPU bus clock and can open 2 memory pages at once which simulates dual-port RAM.
Rev. 2.0 Sys MFG Training/Employee Development

31. Block Diagram: GCTLR & Pallette
PC Peripherals for Technicians
Mar 1998
Block Diagram: GCTLR & Pallette
The Graphics Controller manipulates data flow between the CPU and the Video Buffer.
Provides CPU with an access path to Display Memory.
Controls the data flow between the Display Memory and the Attribute Controller--video to monitor.
The optional video FIFO supplies data to the Attribute Ctlr as required, allowing memory accesses at maximum memory speed rather than the screen refresh rate.
The Attribute Controller: (Contains Palette Regs)
Receives video memory data from the graphics controller & formats the data for display on the CRT.
The palette controls the color and brightness of the signals sent to the monitor.
Rev. 2.0 Sys MFG Training/Employee Development

32. PC Peripherals for Technicians
Mar 1998
Block Diagram: DAC
The Digital to Analog Converter (DAC):
Contains three (RGB) DACs (or RAMDACs) which interface directly to the monitor connector via RFI filters.
Converts the color palette information supplied by the VGA chip to the correct analog voltages to be placed on the red, green, and blue gun outputs to the monitor.
The Video DAC uses the 8-bit input to select one of its 256 color registers (256 different colors at one time).
Each of DACs 256 color registers contains an 18-bit RGB specification (6-bits for each color)
Standard VGA uses 6 bits per color (18 bits / pixel)
218 bits provides any of 256K possible colors in each register.
Note: SVGA DACs can use 8 bits per color (24 bits / pixel)
Rev. 2.0 Sys MFG Training/Employee Development

33. Block Diagram: Video Feature Conn.
PC Peripherals for Technicians
Mar 1998
Block Diagram: Video Feature Conn.
The optional Feature Connector provides support for synchronizing graphics output with external devices.
Permits third party add-on accessories to share signals and control of the VGA circuitry.
Permits direct transfer of video information between the video card and other video devices (3D accelerators, video capture cards, etc), without having to use the system bus.
Also can be used to send signals to a 2nd higher resolution video card that has it’s own high-performance RAMDAC.
Pixel data, Horizontal & Vertical Sync, and Dot Clock signals are available on the feature connector.
Different feature connector standards are available:
Video Feature Connector (VFC), VESA Advanced Feature Connector (VAFC), and VESA Media Channel (VMC) .
Rev. 2.0 Sys MFG Training/Employee Development

34. PC Peripherals for Technicians
Mar 1998
The Video BIOS
The Video BIOS contains a set of well-documented, easy to use routines that provide a low-level programming interface for accessing the hardware and provides compatibility across different hardware platforms.
Applications should make requests through BIOS calls rather than communicating directly with hardware.
Software Interrupt 10 hex is used for Video BIOS routines (e.g. - Set Mode, Write character, Move Cursor, etc.)
The Video BIOS on adapter cards is found during the POST expansion ROM detection (at address C000:0)
The C000 Segment Video BIOS routines usually augment or replace any System BIOS (F000 Seg) video routines.
The INT 10h IVT is re-routed to the Video adapter (C000:xxxx)
INT 42h replaces the default INT 10h IVT (F000:xxxx).
Rev. 2.0 Sys MFG Training/Employee Development

35. VGA Video Port Connector Pinout
PC Peripherals for Technicians
Mar 1998
VGA Video Port Connector Pinout 1 2 3 4 5 15 14 13 12 11 7 10 6 8
Video Signal Levels:
Black = 0v, Full Intensity = +0.7V
Monitor ID bits are used to automatically
sense the type of monitor installed on
power up.
1. Red Video (analog 0-0.7v)
2. Green Video (analog 0-0.7v)
3. Blue Video (analog 0-0.7v)
4. Monitor ID Bit 2
5. Ground (DDC Return)
6. Red Return (ground)
7. Green Return (ground)
8. Blue Return (ground)
9. Key (no pin)
10. Sync Return (ground)
11. Monitor ID Bit 0
12. Monitor ID Bit 1 (DDC Data)
13. Horiz. Sync - TTL (to 90 KHz)
14. Vert. Sync - TTL (50-120Hz)
15. Monitor ID Bit 3 (DDC Clk)
Rev. 2.0 Sys MFG Training/Employee Development

36. VGA Video Port Connectors
PC Peripherals for Technicians
Mar 1998
VGA Video Port Connectors
The VGA uses a 15 pin D-Shell connector to interface with the monitor.
The analog & digital signals are meant to drive an analog color or analog monochrome monitor.
The DAC outputs analog Red, Green, & Blue Video signals to the monitor guns (RS-170).
Black = 0v
Full Intensity = +0.7V
Monochrome monitors use the Green Video for all input.
The RGB lines are terminated in a 75 ohm load at the Graphics Controller and a 75 ohm load at the monitor.
The nominal DC load is 37.5 ohms
Rev. 2.0 Sys MFG Training/Employee Development

37. VGA Video Port Connectors
PC Peripherals for Technicians
Mar 1998
VGA Video Port Connectors
Sync signals are TTL level and polarity were used by the older monitors to determine the video mode for screen sizing (Monitor uses to adjust vertical gain).
e.g. - Display Mode for VGA 350 lines - Mode 10h
Horiz = 31.5 KHz +, Vert = 62.3 Hz -
e.g. - Display Mode for VGA 600 lines - Mode 11h
Horiz = 35.2 KHz -, Vert = 56.2 Hz +
Some newer monitors analyze the sync signals to determine the video mode or use the Plug & Play VESA DDC standard.
Rev. 2.0 Sys MFG Training/Employee Development

38. VGA Video Port Connectors
PC Peripherals for Technicians
Mar 1998
VGA Video Port Connectors
Monitor ID bits [MID3:0] are used to sense the type of monitor installed by the BIOS on power up.
Pulled up by Video Card. Monitor grounds 1 or more.
Not fully standardized & not supported on some systems.
DDC2B-Compliant Monitors
Monitor pins MID1 & MID 3 become DDC Data & DDC Clock lines for this serial communications protocol.
The DDC (Display Data Channel) spec defines a serial communications channel between a computer display and a host system.
Allows the monitor, video card, & the O/S to communicate.
Windows 95's Plug and Play architecture supports DDC.
Rev. 2.0 Sys MFG Training/Employee Development

39. PC Peripherals for Technicians
Mar 1998
DPMS Power Saving
VESA has defined a standard method for the computer to tell the monitor when to go to power saving mode.
This shuts off the deflection & high voltage in the monitor, but the CRT filament remains lit.
When system activity resumes, the display returns almost instantaneously.
The power saving mode is controlled by changing the sync signals according to the list below:
H-sync ON; V-sync ON: Normal (Power Level 100%)
H-sync Off; V-sync ON: Standby (Power Level 80%)
H-sync ON; V-sync Off : Suspend (Power Level <30W)
H-sync Off; V-sync Off : OFF (Power Level <8W)
Rev. 2.0 Sys MFG Training/Employee Development

40. PC Peripherals for Technicians
Mar 1998
REVIEW & SUMMARY
WE HAVE DISCUSSED THE FOLLOWING:
The interactions in a Graphics System
The PC Video Graphics Controller is responsible for producing the image that is displayed on the screen.
An O/S and/or Application updates screen information the using the Video BIOS and/or a Video Device Driver.
The PC Video Subsystem contains a block of dedicated Display Memory that holds the text or graphics information to be displayed on the screen.
The VGA Controller serializes the data in it’s display memory and mixes this stream of data with synchronizing signals that control the video display.
Rev. 2.0 Sys MFG Training/Employee Development

41. PC Peripherals for Technicians
Mar 1998
REVIEW & SUMMARY
How images are displayed on a CRT
The rear part of the CRT contains a cathode that emits an electron beam when heated and the front surface of a computer monitor is actually the end of a large CRT.
The CRT’s electron beam sweeps across the screen in a fixed path from left to right and top to bottom.
The CRT image must be redrawn continuously because it will remain visible for only a few milliseconds depending on the persistence of the phosphor.
In an interlaced graphics system, it takes 2 fields (1 odd, 1 even) to display one complete screen (called a frame).
A non-interlaced display has an entire frame displayed each screen refresh--every line is updated every frame.
Rev. 2.0 Sys MFG Training/Employee Development

42. PC Peripherals for Technicians
Mar 1998
REVIEW & SUMMARY
A block diagram of the Video Subsystem
Clock
SYNTH
Horizontal Timing
Vertical Timing
Dot Stream
To Monitor
CRT
CRT Ctlr
&
Memory
Sequencer
Optional
FIFO
Video
Graphics
Controller
Attribute
(Palette)
System
Bus
Interface
Control
Addr
Data
Ctrl
Feature
Connector
Dot Clock
Mem
DAC
(Lookup Table) R G B
Basic elements usually implemented in an ASIC.
Point & Shoot is used to access registers.
Video Subsystem port connectors (15 pin connector )
Sync signals are TTL level
The DAC outputs analog Red, Green, & Blue Video signals to the monitor guns.
End of Chapter 3-1
Rev. 2.0 Sys MFG Training/Employee Development