Presentation is loading. Please wait.

Presentation is loading. Please wait.

18/6/2007 M.Taborelli, TS-MME Structure fabrication techniques and possibilities M.Taborelli Disk structures Quadrant structures ….most of it inspired.

Published byEsmond Haynes Modified over 9 years ago

Similar presentations

Presentation on theme: "18/6/2007 M.Taborelli, TS-MME Structure fabrication techniques and possibilities M.Taborelli Disk structures Quadrant structures ….most of it inspired."— Presentation transcript:

1 18/6/2007 M.Taborelli, TS-MME Structure fabrication techniques and possibilities M.Taborelli Disk structures Quadrant structures ….most of it inspired by 30GHz tests and experience

2 18/6/2007 M.Taborelli, TS-MME Copper, disk structures - Machining by diamond turning: shape accuracy of 2-3 m in the iris region -alignment of the disks on V-shaped marble before assembly in a stack: use external “cylinder” surface as reference. -assembly by vacuum brazing or by bolting -achieved accuracy? - No rf-damping disk structures

3 18/6/2007 M.Taborelli, TS-MME Ra = 0.05 m disk structures 30 GHz copper structures: surface quality Recrystallization after thermal treatment (vacuum brazing cycle at 820 C)

4 18/6/2007 M.Taborelli, TS-MME Disk structures: other materials and configuration for bimetal -Diamond turing with insert. Successfully tested with Mo and W irises (single iris or full structure) -Insert of complete iris in new material or bi-metal (for iris tip only) -Assembly by clamping (bolting) only, because of the difference in thermal expansion; potential problem for proper electrical contact (oserved copper transfer on refractory metal) Iris insert disk structures

5 18/6/2007 M.Taborelli, TS-MME Copper disks with damping (SLAC design) -Turning is no longer sufficient, milling is necessary to produce the radial slits - Full 3D milling is needed to avoid steps and burrs disk structures

6 18/6/2007 M.Taborelli, TS-MME Why +/- 1 microns precision? 0. Frequency matching (about 4MHz deviation per m on cavity radius at 30 GHz), or tuning 1. Longitudinal alignment precision : <5 m alignment error of the irises induces transversal kick on the beam ; this effect is independent of frequency (11 or 30 GHz) if we keep similar iris aperture 2. RF – to-beam phase: better than 0.1 0 (some microns on cavity shape) to preserve efficiency and beam stability 3.Avoid steps and kinks on the surfaces (field enhancement ) 4. Ra should be around ¼ of the skin depth to preserve electrical conductivity E “bookshelfing” error from cell to cell

7 18/6/2007 M.Taborelli, TS-MME Copper quadrant structures: example 30GHz -machining by 3D milling (carbide tools) -alignment of the quadrants by balls and gooves (plastic deformation of copper): possible improvement? -assembly by brazing or by bolting -achieved accuracy? Grooves are positioned at some 6 m accuracy -damping implemented in the design quadrant structures 160 mm 53 mm

8 18/6/2007 M.Taborelli, TS-MME Tolerances: 5 m shape tolerance

9 18/6/2007 M.Taborelli, TS-MME Metrology on copper quadrants Measurement: coordinate measuring machine, contact with 0.1N force, accuracy +/-3 µm (at CERN), scan pt. by pt. on the surface ………in parallel with RF low power control quadrant structures

10 18/6/2007 M.Taborelli, TS-MME Achieved shape accuracy quadrant structures Surface finishing on copper, Ra=0.1-0.4 mm

11 18/6/2007 M.Taborelli, TS-MME Possible sources of the error in 3D milling -Error on tool diameter, tool length, tool run-out : dynamic dimensions -Error on tool shape -Tool flexure (larger tools at 11GHz should be favourable) -Tool consumption during machining -Thermal expansion of the piece...probably not relevant for the present short prototypes -Temperature stability, dynamics of the machine tool -Positioning accuracy of the machine tool (machine tool with higher nominal accuracy give better surface finish) quadrant structures

12 18/6/2007 M.Taborelli, TS-MME milling Diamond turning, disks HDS60 milling, best result quadrant structures Surface quality: on copper

13 18/6/2007 M.Taborelli, TS-MME Other materials and bi-metal Joining Mo to CuZr C15000 alloy by diffusion bonding through HIP or explosion bonding; tested by machining, shear and pull strength test Cu, Mo, Al, StSt, Ti quadrant structures Full structure in single material for rf testing Explosion bonding HIP diffusion bonding

14 18/6/2007 M.Taborelli, TS-MME Other machining techniques: -3D milling of copper with single crystal diamond tool? -Elliptical vibration milling of copper? -Electrochemical machining sufficiently accurate? -Electro discharge machining of refractory metals ( micro-cracks on molybdenum), development in progress 100 m 1cm Ecole d’ingenieurs Geneva quadrant structures

15 18/6/2007 M.Taborelli, TS-MME Metrology problems Trace of sensor contact HDS11-Aluminium quadrant structures Requires high accuracy, ideally 0.1 m to control at 1 m level Force of the sensor should be low (0.1 N leaves marks) Available optical methods are not adapted for complex 3D shapes

16 18/6/2007 M.Taborelli, TS-MME RF design of structures Mech. design, fabrication, preparation Test, analysis CTF3 SLACKEK R&D Materials, preparation RF Model The goal is the fabrication of 1 geometry in 4 months and 10 geometries per year Production of structures

17 18/6/2007 M.Taborelli, TS-MME Present production situation Available Under production Under mech. Design. Under RF design

18 18/6/2007 M.Taborelli, TS-MME

19 18/6/2007 M.Taborelli, TS-MME HDS11-small-Mo HDS60

Download ppt "18/6/2007 M.Taborelli, TS-MME Structure fabrication techniques and possibilities M.Taborelli Disk structures Quadrant structures ….most of it inspired."

Similar presentations

COOLING TUBE ACCELERATING STRUCTURE MANIFOLD COUPLER VACUUM INTERFACE FLANGE RF INTERFACE FLANGE TUNING STUD ENGINEERING DESIGN AND FABRICATION OF X-BAND.

COOLING TUBE ACCELERATING STRUCTURE MANIFOLD COUPLER VACUUM INTERFACE FLANGE RF INTERFACE FLANGE TUNING STUD ENGINEERING DESIGN AND FABRICATION OF X-BAND.
Task M2 – Advanced Materials and Techniques for Resonant Detectors Motivation : Reduce thermal noise contribution to the acoustic detector noise budget.

Task M2 – Advanced Materials and Techniques for Resonant Detectors Motivation : Reduce thermal noise contribution to the acoustic detector noise budget.
CLIC08 workshop Structure production: CERN activities and Master Schedule G. Riddone, W. Wuensch, R. Zennaro, Contributions from C. Achard, S. Atieh, V.

CLIC08 workshop Structure production: CERN activities and Master Schedule G. Riddone, W. Wuensch, R. Zennaro, Contributions from C. Achard, S. Atieh, V.
Accelerator Science and Technology Centre Prospects of Compact Crab Cavities for LHC Peter McIntosh LHC-CC Workshop, CERN 21 st August 2008.

Accelerator Science and Technology Centre Prospects of Compact Crab Cavities for LHC Peter McIntosh LHC-CC Workshop, CERN 21 st August 2008.
Status of KEK production July 11, 2008 at SLAC KEK T. Higo et al., Accelerator div. T. Takatomi et al., Mech. Eng. Center.

Status of KEK production July 11, 2008 at SLAC KEK T. Higo et al., Accelerator div. T. Takatomi et al., Mech. Eng. Center.
Effects of External Magnetic Fields on the operation of an RF Cavity D. Stratakis, J. C. Gallardo, and R. B. Palmer Brookhaven National Laboratory 1 RF.

Effects of External Magnetic Fields on the operation of an RF Cavity D. Stratakis, J. C. Gallardo, and R. B. Palmer Brookhaven National Laboratory 1 RF.
Status of the 201 MHz Cavity and Coupling Coil Module Steve Virostek Lawrence Berkeley National Laboratory MICE Video Conference March 10, 2004.

Status of the 201 MHz Cavity and Coupling Coil Module Steve Virostek Lawrence Berkeley National Laboratory MICE Video Conference March 10, 2004.
Design of Standing-Wave Accelerator Structure

Design of Standing-Wave Accelerator Structure
2 nd collaboration meeting on X-band Accelerator Structure Design and Test-Program Structure fabrication Comparative analysis of disk and quadrant manufacture.

2 nd collaboration meeting on X-band Accelerator Structure Design and Test-Program Structure fabrication Comparative analysis of disk and quadrant manufacture.
DELTA Quadrant Tuning Y. Levashov, E. Reese. 2 Tolerances for prototype quadrant tuning Magnet center deviations from a nominal center line < ± 50  m.

DELTA Quadrant Tuning Y. Levashov, E. Reese. 2 Tolerances for prototype quadrant tuning Magnet center deviations from a nominal center line < ± 50  m.
S Temple CLRC1 End-cap Mechanics FDR Cooling Structures Steve Temple, RAL 1 November 2001.

S Temple CLRC1 End-cap Mechanics FDR Cooling Structures Steve Temple, RAL 1 November 2001.
CIEMAT CONTRIBUTION TO TBL PETS (January 2009) David Carrillo on behalf of the Accelerators Team.

CIEMAT CONTRIBUTION TO TBL PETS (January 2009) David Carrillo on behalf of the Accelerators Team.
Status of X-band program at RadiaBeam

Status of X-band program at RadiaBeam
SRF Results and Requirements Internal MLC Review Matthias Liepe1.

SRF Results and Requirements Internal MLC Review Matthias Liepe1.
Accelerating structure test results and what’s next Walter Wuensch CTF3 collaboration meeting 16-1-2007.

Accelerating structure test results and what’s next Walter Wuensch CTF3 collaboration meeting
First TBL PETS prototype tank development D. Carrillo, E. Rodríguez, F. Toral, CIEMAT N. Chritin, S. Doebert, I. Syratchev, CERN CERN, 24/01/2008 Courtesy.

First TBL PETS prototype tank development D. Carrillo, E. Rodríguez, F. Toral, CIEMAT N. Chritin, S. Doebert, I. Syratchev, CERN CERN, 24/01/2008 Courtesy.
RFQ Thermal Analysis Scott Lawrie. Vacuum Pump Flange Vacuum Flange Coolant Manifold Cooling Pockets Milled Into Vanes Potentially Bolted Together Tuner.

RFQ Thermal Analysis Scott Lawrie. Vacuum Pump Flange Vacuum Flange Coolant Manifold Cooling Pockets Milled Into Vanes Potentially Bolted Together Tuner.
International Workshop on Linear Colliders 2010 Design and fabrication update on PSI/Trieste X-band phase- space rotator structure Dmitry Gudkov 21-OCT-2010.

International Workshop on Linear Colliders 2010 Design and fabrication update on PSI/Trieste X-band phase- space rotator structure Dmitry Gudkov 21-OCT-2010.
Investigation threads on fabrication technologies for the CLIC X-band Accelerating Structures C. Rossi on behalf of the CLIC X-band Activity Thanks for.

Investigation threads on fabrication technologies for the CLIC X-band Accelerating Structures C. Rossi on behalf of the CLIC X-band Activity Thanks for.
Cutting Technology –chip removing –the largest class of manufacturing activities in engineering production –~1.87 million machine tools –~$168 billion.

Cutting Technology –chip removing –the largest class of manufacturing activities in engineering production –~1.87 million machine tools –~$168 billion.

Similar presentations

Ads by Google