1. KANON LIQUID HANDLING Suite 4, Brookside House Business Centre, Spring Road, Ibstock, Leics. LE67 6LR Tel : 01530 263000 Fax : 01530 264222 E-mail : info@kanon.uk.com

2. View This Presentation Of The Benefits And Operating Principle Of The Kanon Magnetic Sphere Product Recovery System Thank You For Setting Aside A Few Minutes Of Your Valuable Time To

3. Kanon Magnetic Sphere Product Recovery Systems are used to recover product from pipelines once the product supply has been exhausted or a particular production run has been completed. Earlier versions of this type of system were known as Pigging systems.

4. The name originates from the oil industry. Discs connected by a rod were propelled through oil pipelines to determine the amount of corrosion on the inside walls. These disc sets were known as Pipeline Internal Gauges or PIGS………… Why is it called a pig ? Another, more colourful explanation, is that when Pigs were sent through oil pipelines, to remove the build-up of paraffin wax from the internal wall, they made a squealing noise like a pig and the name stuck!…………

5. The Magnetic Sphere System has been tested by the Campden & Chorleywood Food Research Association, against hygiene criteria laid down by the European Hygienic Equipment Design Group, and is recommended by C.C.F.R.A. for use within the hygienic processing industry.

6. The major benefits of the system are: Hygienic in-line system - no off-line cavities. High levels of Product Recovery and Waste Reduction. Can be fitted, even retrospectively, into almost any pipeline installation. Magnetic Spheres can negotiate 1.5D radius bends, Tube in Tube Heat Exchangers, Flow Plates and all standard hygienic Stainless Steel fittings. Available in both single and double sphere formats. Offers real value for money against competitive systems.

7. The Magnetic Sphere Product Recovery System is a Past Winner in the……. …….Food Processing Magazine’s Annual Hygiene Awards

8. The following slides demonstrate the operating principle of a Kanon Twin Magnetic Sphere Product Recovery System. A Twin Sphere system is recommended when either the Transfer line is full of residual water, or when the product being introduced is prone to aeration. The first Magnetic Sphere precedes the introduced product through the Transfer line and prevents contamination or aeration. If neither case applies a Single Sphere System is suitable.

9. Before Product Introduction Line Empty Or Full Of Rinse Water Following Previous C.I.P. Procedure PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

10. Product Introduction Product Valve Opened – Pump Started – First Magnetic Sphere Launched – Drain Valve At Receiver Opened - Any Residual Water Or Air Discharged To Drain And Prevented From Coming Into Contact With Product PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RETURN MEDIUM DRAIN RECOVERY FLUID DRAIN

11. Product Introduction Product Valve Opened – Pump Started – First Magnetic Sphere Launched – Drain Valve At Receiver Opened - Any Residual Water Or Air Discharged To Drain And Prevented From Coming Into Contact With Product PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RETURN MEDIUM DRAIN RECOVERY FLUID DRAIN

12. First Magnetic Sphere Detected At Receiver Drain Valve Remains Open For Timed Period To Purge Receiver PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RETURN MEDIUM DRAIN RECOVERY FLUID DRAIN

13. Product Transfer Commences Timer Times Out – Drain Valve Closes – Line Valve Opens PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

14. Product Transfer Complete Transfer Pump Stopped – Product Valve Closed – Second Magnetic Sphere Moved Into Launch Position – Recovery Fluid Introduced – Magnetic Sphere Launched – Product In Pipeline Recovered To Process PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

15. Product Transfer Complete Transfer Pump Stopped – Product Valve Closed – Second Magnetic Sphere Moved Into Launch Position – Recovery Fluid Introduced – Magnetic Sphere Launched – Product In Pipeline Recovered To Process PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

16. Second Magnetic Sphere Detected At Receiver Product Recovery Complete – Line Valve Closed – Drain Valve Opens For Timed Period To Allow Recovery Fluid To Purge Receiver PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

17. Line Is Now Ready For C.I.P. If Required Magnetic Sphere System Is Cleaned Along With Process Pipework – If C.I.P. Is Not Required The Magnetic Spheres Can Be Returned To The Launcher Following Product Recovery PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

18. During C.I.P. The Receiver Magnet Carriages Should Be Moved Between The “Park” And “Launch” Positions Occasionally To Ensure That The Magnetic Spheres Are Thoroughly Cleaned – Drain Valves Should Be Pulsed Open At Intervals PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

19. During C.I.P. The Receiver Magnet Carriages Should Be Moved Between The “Park” And “Launch” Positions Occasionally To Ensure That The Magnetic Spheres Are Thoroughly Cleaned – Drain Valves Should Be Pulsed Open At Intervals PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

20. During C.I.P. The Receiver Magnet Carriages Should Be Moved Between The “Park” And “Launch” Positions Occasionally To Ensure That The Magnetic Spheres Are Thoroughly Cleaned – Drain Valves Should Be Pulsed Open At Intervals PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

21. During C.I.P. The Receiver Magnet Carriages Should Be Moved Between The “Park” And “Launch” Positions Occasionally To Ensure That The Magnetic Spheres Are Thoroughly Cleaned – Drain Valves Should Be Pulsed Open At Intervals PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

22. During C.I.P. The Receiver Magnet Carriages Should Be Moved Between The “Park” And “Launch” Positions Occasionally To Ensure That The Magnetic Spheres Are Thoroughly Cleaned – Drain Valves Should Be Pulsed Open At Intervals PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

23. During C.I.P. The Receiver Magnet Carriages Should Be Moved Between The “Park” And “Launch” Positions Occasionally To Ensure That The Magnetic Spheres Are Thoroughly Cleaned – Drain Valves Should Be Pulsed Open At Intervals PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

24. Magnetic Spheres Returned To Launcher Drain Valve At Launcher Opened – Return Medium Valve Opened – Magnetic Spheres Launched From Receiver – Rinse Water Remaining In Pipeline Is Discharged To Drain Via The Launcher Drain Valve PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

25. Cycle Complete Magnetic Spheres Back In Launcher – Line Clean And Empty – Ready For Next Product Transfer PRODUCTION FACILITY OR HOLDING TANK LAUNCHERRECEIVER HOLDING TANK OR FILLING MACHINE RECOVERY FLUID DRAIN RETURN MEDIUM DRAIN

26. If you require any further information about the Kanon Magnetic Sphere Product Recovery System, or wish to arrange an on site demonstration, contact either Glynn Williams or Kathryn Clarke at our Ibstock office or visit our website www.kanon.uk.com

27. KANON LIQUID HANDLING Suite 4, Brookside House Business Centre, Spring Road, Ibstock, Leics. LE67 6LR Tel : 01530 263000 Fax : 01530 264222 E-mail : info@kanon.uk.com