1. Petroleum Equipment InstituteRP
Recommended Practices for Installation of Aboveground Storage Systems for Motor Vehicle Fueling

3. RP 200-13 Introduction Scope
Includes aboveground, stationary, shop-fabricated tanks. Does not include field-fabricated storage tanks or storage systems for liquefied petroleum gases, liquefied natural gases or compressed natural gases.

4. Emphasizes the Importance of Using Competent InstallersRP
1. Introduction
Emphasizes the Importance of Using Competent Installers

5. RP 200-13 2. Site Planning Change: Added: See RP1000 Tank Location
Tank Configurations
Property Lines and Bldgs
Tank Spacing Requirements
Bases and Foundations
Retail Service Stations
Commercial Fleet Facilities
Marinas (Change)
Product Deliveries
Traffic Flow
SPCC Plan
Electronic Equipment Physical Protection
Fire Protection
Utilities
Emergency Planning
Change: Added: See RP1000

6. 3. Foundations, Support and AnchorageRP
3. Foundations, Support and Anchorage
General
Soil Analysis
Foundation Design
Excavation
Base Course
Vertical Tank Bases
Horizontal Tank Saddles
Reinforced Concrete Slabs
Anchoring

7. RP 200-13 4. Dikes Purpose Dike Capacity Dike Construction
Impervious Barrier
Dike Penetraions
Access
Drainage Control
Oil/Water Separator

8. 5. Vaults and Special EnclosuresRP
5. Vaults and Special Enclosures
General
Vault Design
Vault Construction
Venting
Leak Detection
Liquid Recovery
Vault Ventilation
Collision Protection
Electrical Installation
Special Enclosures

9. RP 200-13 6. Tanks Changes: Deleted UL2244 (Tank System)
General
Standards (Changes)
Tank Openings
Preinstallation Inspection
Material Handling
Air-and-Soap Test
Changes:
Deleted UL2244 (Tank System)
Added STI F921 (Integral Secondary Containment)
Added STI F941 (Fireguard)

10. RP 200-13 7. Pumps and Valves Materials and Design Pumping Systems
Fire/Emergency Valves
Block Valves
Anti-Siphon Valves
Check Valves
Pressure Relief Valves

11. 8. Tank Filling, Gauging, Dispensing and VentingRP
8. Tank Filling, Gauging, Dispensing and Venting
Materials and Design
Tank Filling
Dispensing Systems
Gauging Systems
Tank Venting

12. 9. Aboveground Piping and FittingsRP
9. Aboveground Piping and Fittings
General Requirements
AST Piping Materials
Piping Practices
Piping Layout
Fittings for AST Piping
Testing AST Piping
Piping Corrosion Protection

13. 10. Underground Piping and FittingsRP
10. Underground Piping and Fittings
General Requirements
Piping Materials
Piping Practices
Layout and Trenches
Backfill and Compaction
Fittings
Corrosion Protection
Fiberglass Piping
Flexible Piping
Containment Sumps
Testing Primary Piping
Testing Secondary Piping

14. RP 200-13 11. Corrosion Protection General Applicability Coatings
Protection of Buried Components
Galvanic CP
Impressed-Current Sys
Wiring and Electrical
Inspection and Testing

15. 12. Environmental ProtectionRP
12. Environmental Protection
General
Release Detection
Vapor Recovery

16. 13. Electrical InstallationRP
13. Electrical Installation
General Requirements
Classifications
Electrical Equipment
Emergency Shutoff
Wiring
Intrinsically Safe
Grounding and Bonding
Ensuring Uninterrupted Power

17. 14. Testing and InspectionRP
14. Testing and Inspection
General
Test Results
Other Testing

18. 15. Documentation, Maintenance and TrainingRP
15. Documentation, Maintenance and Training
As-Built Drawings
Component Documentation
Scheduled Maintenance
Training

19. Size Calculations for DikesRP
Appendix A
Size Calculations for Dikes

20. RP
Appendix B
Venting

21. Code Requirements for ASTs at Motor Vehicle Fuel Dispensing FacilitiesRP
Appendix C
Code Requirements for ASTs at Motor Vehicle Fuel Dispensing Facilities

22. RP
Appendix C
Code Requirements
NFPA 30A (2008)
IFC (2006)

23. Publication ReferenceRP
Appendix D
Publication Reference