Presentation is loading. Please wait.

Presentation is loading. Please wait.

MODULAR SMPS POWER PLANT

Similar presentations


Presentation on theme: "MODULAR SMPS POWER PLANT"— Presentation transcript:

1 MODULAR SMPS POWER PLANT
PUNCOM offers SMR-48V/33A , a switch mode rectifier module, designed to provide up to 33A of output current into a 48V nominal system for telecom, datacom, industrial and IT applications. It Converts V AC input power at 50 or 60 Hz into a highly regulated, filtered, low noise and isolated 48V DC output. The unit is designed for N+1 redundant configurations. Up to eight rectifier modules can fit in a single 19” rack to provide 231A of current in N+1 configuration. Up to fifteen rectifiers can be configured in two 19” racks for a 462A ultimate capacity system in N+1 configuration using one control and supervisory unit (MiniCSU). The system can also be monitored and controlled remotely through modem or internet. The rectifier has been designed with a “plug-and-play” feature i.e. when a rectifier module is plugged into a live system the relevant system parameters are automatically downloaded from the MiniCSU, making rectifier replacement a completely hands-off operation. The unit is fully hot pluggable. SALIENT FEATURES Hot Pluggable. 231A in a 19” rack in N+1 configuration and 462A in two 19” racks in N+1 configuration. Wide range of AC input, V provides protection from power disturbances and in combination with high interrupting capacity fast acting fuses translates into better reliability. Battery temperature compensation Compliant to IEC & CISPR 22 specs for EMI/EMC. Optional RS 232, RS 485,10Base T ethernet and modem interfaces. Fully menu driven with user friendly navigator push buttons menu. Active power factor correction > 0.98. Very High power density > 4.0W/inch3. High efficiency: better than 90% at > 50% load. Plug and play capability without any adjustments. Digital active current sharing. Password protection against unauthorized parameters change.

2 Punjab Communications Limited
SPECIFICATIONS INPUT CHARACTERISTICS Voltage Nominal Rated voltage range Extended low voltage range Extended high voltage range Current Frequency Power factor Harmonic Distortion Efficiency Inrush Current Soft Start Protection Voltage Withstand Test 220VAC VAC 90-150VAC (With 50% automatic power derating) VAC 14A RMS at 150VAC 9A RMS at 220VAC 45-66Hz >0.98 at 40%-100% load Current THD<6% (full load) if Voltage THD<1% Better than 90% at >50% load <8A peak at nominal mains voltage Ramp up time 8 seconds to full load HRC input fuse for input Live Over voltage shutdown at 300VAC Under voltage shutdown at 85VAC 1500VAC input to chassis for one minute Protection Reverse Polarity Over voltage Over current Over temperature Voltage Withstand test Fuse at output protects against reverse polarity Only faulty unit shuts down Can sustain short Circuit indefinitely Gradual reduction of power limit if heat sink temp exceeds preset limit 1000VAC output to chassis for one minute FEATURES Indicators Controls/Adjustments (Via MiniCSU) Status normal-green LED Minor alarm-Yellow LED Major alarm-Red LED Float/equalize voltage Current limit HVSD level and reset Equalize mode Individual remote shutdown OUTPUT CHARACTERISTICS Voltage Float Equalize Current Limit Power Static Regulation Line Load Dynamic Regulation Noise Load Sharing MECHANICAL 48-58V V 5A to 34A 1800W Better than ±0.02% Voltage drops by 0.56V ±0.03V from zero to 33A for stand alone & better than ± 0.05% for MiniCSU controlled unit ±5% for 10% to 90% step load ±1% of final value within 1msec of step change ±0.1% for a 25% step change in AC input voltage <2mV RMS psophometric weighted <10mV RMS (10KHz-100MHz) <100mV peak to peak (10KHz- 100MHz) Better than ±5% of full scale with active current sharing from MiniCSU Dimensions Rack W x H x D Module W x H x D MINICSU W X H X D Weight SMR/MINICSU 600mm x 1465mm x 595mm (max.) 87mm x 266mm x 320mm 176mm x 44mm x 266mm < 6Kg/1.3KG ENVIRONMENTAL Temperature Operating range Derated operation Storage Humidity Cooling Altitude EMI/EMC -25oC to +50oC 50oC to 70oC, 50% automatic power derating -40oC to +70oC 0 to 95% RH non-condensing Natural convection / Forced Cooling Derate max ambient temperature by 4oC per 1000m above sea level to 3000m Meets IEC specs for EMC immunity and CISPR 22 class B for EMC emissions Specifications subject to change without prior notice. 040605 Punjab Communications Limited B-91, Phase VIII, Industrial Area, Mohali, Punjab India Phone: , Fax: , Visit us at:


Download ppt "MODULAR SMPS POWER PLANT"

Similar presentations


Ads by Google