1. General System Configuration
Figure 3.1
Inputs
IC-1600 INTELLIGENT CONTROLLER
READER INTERFACE (RI-130)
Receive
Ground
Transmit
J13 J5
J12
J15 J1
Data +
Data -
Enable +
Enable - J9 S1 S2 J5 J6
Data +
Data -
Enable +
Output Points
Input Power
Enable -
Max distance”2 miles”
CardReader
Channels
Max distance 500’
Power Supply
J18
(24VDC)
Ground
Battery -
Battery +
120VAC 60hz
120VAC 60hz
General System Configuration
Overview

2. RI-130 DIAGRAM Figure 3.2 Lower board Upper board J13 J14 J12 J15 J5
J5 goes to a channel
on an IC-1600 or CE-1600
Figure 3.2
Lower board
Upper board
J13
J14
J12
J15 J5 J6 S1 S2
Data +
Data -
Enable +
Go Output 0 Common
Enable -
Go Output 0 Normally Open
J12 connects to
the card reader
Not Used
Go Output 0 Normally Closed
Shunt Output 1 Common
off
Shunt Output 1 Normally Open
5VDC
Shunt Output 1 Normally Closed
15VDC
Output 2 Common
Output 2 Normally Open
Ground
Output 2 Normally Closed
Led
Data1
Data0
off
S1 configures the RI-130’s
Go and Shunt time for
Degraded Mode
Input 0 Door open Detect
Input 1 Exit Push-Button
Input 2 Tamper Detect
Input 3
Common ( J14)
Input 4
Input 5
S2 configures the RI-130
System code for
Degraded Mode
Input 6
12vac/12VDC+
Input 7
12vac/12VDC-
Input 8
Ground
Input 9
Ground
Input 10
Not Used
Input 11
J6 is the input
power to the RI-130
RI-130 DIAGRAM

3. RI-130 DIAGRAM Figure 5.1 The Door Open Detect Monitor Point J13 J14
“Unauthorized Door Open Reporting” in Card Reader definition
Door Sequences
“Report Only if Held Beyond Shunt Time”
“Report As Forced Entry Detect (FED)”
In AG “Forced Entry” is reported
as Door opens under
Monitor Activity
In AG “Forced Closed” is
reported as Door Closes
under Monitor Activity
When the Door is
opened, without
“Access Granted”
or an
“Unlock Command”
-Shunt Relay Energizes
-Door may stay open until Shunt Time expires
-If the door is still open after the
shunt time, the “Door Held Open” is
reported under Monitor
Nothing is reported in AG.
Both relays reset as
door closes
Nothing is reported in AG.
Both relays reset as door
closes.
When Access is Granted.
Door opens, then
Door closes
before Go Relay
Times out. To
Door Contact
When Access is Granted.
Door opens, then
Door closes
before Shunt Relay
Times out.
Nothing is reported in AG.
Shunt Relay resets as
door closes.
Nothing is reported in AG.
Shunt Relay resets
as door closes
In AG “Door Held Open”
is reported under
Monitor Activity
In AG “Door closed” is
reported after the door closes
under Monitor Activity
In AG “Door Held Open”
is reported under
Monitor Activity
In AG “Door closed” is
reported after the door closes
under Monitor Activity
Access is Granted.
Door opens, then
Door closes
after Shunt Relay
Times out.
Common
Door Open Detect

4. RI-130 DIAGRAM Figure 5.2 The Door Open Detect Monitor Point J15 J12
“Unauthorized Door Open Reporting” in Card Reader definition
Shunt Common
& Normally open
“Report Only if Held Beyond Shunt Time”
“Report As Forced Entry Detect (FED)”
Door Sequences
J12
In AG“Forced Entry” is reported
as Door opens under Monitor Activity
In AG “Forced Closed” is reported
as Door Closes under Monitor Activity
Door is opened,
without
“Access Granted”
or an
“Unlock Command”
Will not function
Access is Granted.
Door opens, then
Door closes
before Go Relay
Times out.
Nothing is reported in AG.
Both relays stay energized for
the whole duration or the
relays’ respected times.
Nothing is reported AG.
Both relays stay energized for
the whole duration or the
relays’ respected times.
J14
J13 To
Door Contact
Door Open Detect
Access is Granted.
Door opens, then
Door closes
before Shunt Relay
Times out.
Nothing is reported AG.
Shunt Relay stays energized for
the whole duration of the
shunt time.
Nothing is reported AG.
Shunt Relay stays energized for
the whole duration of the
shunt time.
In AG “Door Held Open” is reported
under Monitor Activity
In AG “Door closed” is reported
after the door closes under
Monitor Activity
Access is Granted.
Door opens, then
Door closes
after Shunt Relay
Times out.
Will Not Function