1. Industry leading completions execution and service quality

2. Allied-Horizontal Wireline Services
Provides a differentiated service quality and technological capability
Experienced and dedicated management team
Experienced and committed service crews
Customer-oriented culture
Built to provide Value

3. Highest Value Provider…
Executes jobs safely
Provides high efficiency / service quality
Provides technology solutions
Has the ability to lower the overall development cost

4. Allied-Horizontal focus:
People Process Equipment Technology Value
VALUE

5. ShortSTAK™ Composite Frac Plug
No Cast Iron Components
Proprietary seal system
4-1/2” and 5-1/2” sizes
Only 7” long when set
Holds 10,000 psi
360° Slip system ensures positive casing engagement

6. Patented Slip Profile
Proprietary slip profile on the Powdered Metal Slips push the ShortSTAK™ into the Mill
Does not continue rotating thus robbing force from the Mill
Lines show the upwards slide of slip until it locked

7. ShortSTAK™ Composite Frac Plug
Minimal milling time, clutch feature reduces drill up time
Uses standard E-4 or Go Shorty setting tool
Anti-preset design allows deployment to the desired depth
Optional Pump Down Ring saves time and water
Clutch on both ends prevent spinning of the plug when engaged to the lower plug during mill-out

8. Shortest Plug on the Market
ShortSTAK™ - 7 in.
Boss Hogg – 17 in.
Obsidian – 32 in.

9. Debris Comparison – ShortSTAK™ vs Competition
Competition 15 min average
ShortSTAK 3 min average
Same Well, BHA, & Number of Plugs
Milled with Hurricane bit on stick pipe
3 min average for ShortSTAK
15 min average for Competition
Polymer sweeps at 5.2 bpm after every 3 plugs
Significantly smaller pieces

10. ShortSTAK™ Composite Frac Plug
15 ShortSTAK Frac Plugs (5-1/2” 23#) drilled utilizing coiled tubing with JZ bit.
Average time was 3 min each.

11. Setting the ShortSTAK™ Composite Frac Plug
Force from the ball keeps the plug set

12. Traditional Frac Plug Setting Procedure
Set Traditional Frac Plug
Unset Traditional Frac Plug
Traditional Frac plug is now unsupported
Force from the ball transfers all of the load to the bottom sub

13. Brass Ring Expands as ShortSTAK™ is Set
Section “A-A” A
Casing ID
Brass Ring
Composite Body
Composite
Rubber
Brass
Proprietary sealing system virtually eliminates any extrusion gap between the composite body of the ShortSTAK and the ID of the casing.

14. ShortSTAK™ Frac Plug with Flapper
Flapper held open by shear pins
Composite Flapper installed in ShortSTAK
Shear pins sheared and flapper closed
Shear Pins

15. Setting the ShortSTAK™ Composite Frac Plug with Flapper
Pressure from below pushes the flapper open and allows flowback
Additional force from the frac closes the flapper. Just like the ball on seat, it puts additional force into the slips.
Since the flapper doesn’t fully close, flow can go both directions past the flapper

16. Composite ShortSTAK™ Endurance Test 4hr and 36 min

17. Composite ShortSTAK™ Specifications
Casing/Liner Size
Casing/Liner Weight
Tool OD
Tool OAL Set
Pressure Rating
Temp Rating
Tool ID
Ball Size
4.5 in.
11.6 lb./ft.
3.66 in.
7.0 in.
10,000 psi
50° F
1.25 in.
2.0 in.
13.5 lb./ft.
3.60 in.
15.1lb./ft.
3.50 in.
5.5 in.
17 lb./ft.
4.56 in.
20 lb./ft.
4.46 in.
23 lb./ft.
4.36 in.

18. Proven Track Record in Every Key Oil & Gas Basin
Bakken
Niobara
Utica
Marcellus
Barnett
Woodford
Permian
Eagle Ford

19. Safety, People, Process, Equipment and Technology
Our objective is to provide the safest and most efficient wireline services in the industry.
This is more than a simple statement, it is the foundation of our business. We aspire to achieve this everyday through a rigid focus on providing only the best:
Safety, People, Process, Equipment and Technology
alliedhorizontal.com