1. How are electrons organized around a nucleus?

2. Electrons can be assigned to principal energy levels or “electron shells.”

3. Li – 2 in the 1st and 1 in the 2nd
The electron configuration on the PT indicates how many electrons there are in each energy level.
Li – 2 in the 1st and 1 in the 2nd
Ca – 2 in the 1st 8 in the 2nd in the 3rd in the 4th
**An electron in a lower energy level has less energy than an electron in a higher energy level

4. Vocabulary Terms:
Valence electrons – the electrons located in the highest occupied principle energy level or shell
Kernel electrons – all of the electrons that are not valence (the electrons in the inner shells)

5. Periodic Table shows the number of valence electrons
The last number of the electron configuration is the number of valence electrons

6. Lewis-Dot Diagrams
Used to show only the valence electrons around an atom or ion.

7. C Ne Lewis-Dot Diagrams Draw the first two e- dots together
If needed, draw the next three as single dots
If even more are needed, start to double up the single positions.
Lewis-Dot Diagram of C Ne C

8. The location of an electron can change.
An electron can move from a low to a higher energy level by absorbing energy
An electron releases (emits) energy when it falls from a high to a lower energy level
Decreasing energy

9. When electrons change in energy level, the atom changes in “state.”
Ground state – the electrons are in the lowest possible energy levels (usually as close to the nucleus as possible)
The electron configuration on the Periodic Table represents the ground state
Excited state – at least one electron has absorbed energy and is in a higher energy level than it would be in the ground state

10. Identify an Element Based on Electron Configuration
For atoms the total number of electrons identifies the element.
The total number of electrons is equal to the atomic number.
Even for atoms in an excited state, the total number of electrons will be equal to the atomic number.

11. As electrons transition between energy levels, a spectral pattern is produced.
A bright-line (emission) spectrum is produced when electrons that are already excited emit energy as they fall from a high to a lower energy level

12. Hydrogen’s Spectral Pattern

13. As electrons transition between energy levels, a spectral pattern is produced.
An absorption spectral pattern is produced when the electrons absorb energy and move from a low to a higher energy level

14. The flame test is based on electrons’ changes in energy levels
Electrons must first absorb energy moving from low to higher energy levels,
Then already excited electrons emit energy as they fall from high to lower energy levels.

15. Electrons exist in orbitals.
Sometimes called “electron clouds”
Regions of high probability of finding the electrons

16. Different principal energy levels have different sublevels
1st energy level only has s
2nd energy level has s and p
3rd energy level has s, p, d
4th energy level has s, p, d, f
5th level + also has s,p,d,f

17. **Each orbital can hold up to 2 electrons
Any s – sublevel
Has only one orbital
**Each orbital can hold up to 2 electrons
So, an s orbital sublevel can only hold 2 electrons maximum

18. Has 3 individual orbitals Can hold up to 6 electrons
Any p – sublevel
Has 3 individual orbitals
Can hold up to 6 electrons

19. Has 5 individual orbitals Can hold up to 10 electrons
Any d – sublevel
Has 5 individual orbitals
Can hold up to 10 electrons

20. Has 7 individual orbitals Can hold up to 14 electrons
Any f – sublevel
Has 7 individual orbitals
Can hold up to 14 electrons

21. Aufbau Principle
Electrons fill orbitals in order of low energy to high energy

22. Hund’s Rule
When electrons occupy multiple orbitals at the same sublevel (ex. 2p), one electron enters each orbital until all have one.
If there are additional electrons, they start to pair up, with the spin that is opposite of the existing electron.

23. Pauli Exclusion Principle
Remember, an orbital can only hold a maximum of two electrons
If two electrons occupy the same orbital, they must have opposite spins

24. Electron Configuration: Orbital Notation

25. The Maximum Number of Electrons at each Principal Energy Level
You can determine the number of electrons that completely fill each PEL with the equation 2n2
Plug in the PEL number as “n”
For the 1st PEL: 2n2 = 2(1)2 = 2
For the 2nd PEL: 2n2 = 2(2)2 = 8
For the 3rd PEL: 2n2 = 2(3)2 = 18
For the 4th PEL: 2n2 = 2(4)2 = 32

26. Ground State vs Excited State using Sublevel Notation Electron Configuration
Sodium’s configuration in the ground state:
1s22s22p63s1
The total number of electrons is equal to the atomic number
The electrons fill the sublevels in the correct order
A possible configuration for sodium in the excited state:
1s22s22p53s13p1
The total number of electrons is still equal to the atomic number
But the electrons do not completely fill all sublevels in the correct order
For this example, 2p should be filled with 6 electrons before electrons fill a higher sublevel