1. Computer Architecture

2. ARM Processor

3. Why ARM?
As of 2007, about 98% of the more than one billion mobile phones sold each year use at least one ARM processor.
As of 2009, ARM processors account for approximately 90% of all embedded 32-bit RISC processors
source:

4. History
ARM was developed at Acron Computer Limited of Cambridge, England between 1983 and 1985
RISC concept introduced in 1980 at Stanford and Berkley
ARM Limited founded in 1990
ARM Cores
Licensed to partners to develop and fabricate new micro-controllers

5. ARM Architecture
Based upon RISC Architecture with enhancements to meet requirements of embedded applications
A large uniform register file
Load-store architecture, where data processing operations operate on register contents only
Uniform and fixed length instructions
32-bit processor
Instructions are 32-bit long
Good Speed/Power Consumption Ratio
High Code Density

6. Enhancement to Basic RISC Features
Variable cycle execution for certain instructions
load-store-multiple instructions
Inline barrel shifter leading to more complex instructions
Preprocessing one of the input registers before use
Thumb 16-bit instruction set
Code density improved by 30% over 32-bit instructions
Enhanced DSP instructions
Support fast 16x16 multiplier operations

7. Enhancement to Basic RISC Features
Auto-increment and auto-decrement addressing modes to optimize program loops
Load and Store Multiple instructions to maximize data throughput
Conditional Execution of instruction to maximize execution throughput

8. ARM Architecture Versions
26 bit addressing, no multiply or co-processor
Version 2
Includes 32-bit result multiply co-processor
Version 3
32 bit addressing
Version 4
Add signed, unsigned half-word and signed byte load and store instructions
Version 4T
16-bit Thumb compressed form of instruction introduced

9. ARM Architecture Versions
Version 5T
Superset of 4T adding new instructions
Version 5TE
Add signal processing signal extension
Examples:
ARM 6: v3
ARM 7: v3, ARM7TDMI: v4T
StrongARM: v4
ARM 9E-S: v5TE

10. Overview: Core Data Path
Data items are placed in register file
No data processing instructions directly manipulate data in memory
Instructions typically use two source registers and single result or destination registers
A Barrel shifter on the data path can pre-process data before it enters ALU
Increment/decrement logic can update register content for sequential access independent of ALU

11. Basic ARM Organization

12. Registers General Purpose registers hold either data or address
All registers are of 32 bits
In user mode 16 data registers and 2 status registers are visible
Data registers: r0 to r15
Three registers r13, r14, r15 perform special functions
r13: stack pointer
r14: link register
r15: program counter

13. Registers (2)
Depending upon context, registers r13 and r14 can also be used as GPR
Any instruction which use r0 can as well be used with any other GPR (r1-r13) (Orthogonal)
In addition, there are two status registers
CPSR: current program status register
SPSR: saved program status register

14. Status Registers
CPSR: monitors and controls internal operations

15. CPSR: Example

16. ARM Status Bits
Every arithmetic, logical, or shifting operation sets CPSR bits:
N (negative), Z (zero), C (carry), V (overflow).

17. Processor Modes Processor modes determine
Which registers are active, and
Each processor mode is either
Privileged: full read-write access to the CPSR
Non-privileged: read-only access to the control field of CPSR but read-write access to the condition flags

18. Processor Modes (2) ARM has seven modes
Privileged: abort, fast interrupt request, interrupt request, supervisor, system and undefined
Non-privileged: user
User mode is used for programs and applications

19. Privileged Modes Abort when there is a failed attempt to access memory
Fast Interrupt Request (FIQ) & interrupt request
correspond to interrupt levels available on ARM
Supervisor mode
state after reset and generally the mode in which OS kernel executes

20. Privileged Modes (2) System mode
special version of user mode that allows full read-write access of CPSR
Undefined
when processor encounters an undefined instruction

21. Processor Modes

22. Processor Modes

23. Banked Registers Register file contains in all 37 registers
20 registers are hidden from program at different times
These registers are called banked registers
Banked registers are available only when the processor is in a particular mode
Processor modes (other than system mode) have a set of associated banked registers that are subset of 16 registers
Maps one-to-one onto a user mode register

24. Register Banking

25. SPSR
Each privileged mode (except system mode) has associated with it, a Save Program Status Register or SPSR
This SPSR is used to save the state of CPSR (Current Program Status Register) when the privileged mode is entered in order that the user state can be fully restored when the user process is resumed

27. Mode Changing
Mode changes by writing directly to CPSR or by hardware when the processor responds to exception or interrupt
To return to user mode a special return instruction is used that instructs the core to restore the original CPSR and banked registers

28. Mode Changing

29. ARM Instruction Set

30. Instructions
Instructions process data held in registers and access memory with load and store instructions
Classes of instructions:
Data processing
Branch instructions
Load-store instructions
Software interrupt instructions
Program status register instructions

31. Features of ARM instruction set
3-address data processing instructions
Conditional execution of every instruction
Load and store multiple registers
Shift, ALU operation in a single instruction

32. ARM data instructions Basic format: ADD r0,r1,r2
Computes r1+r2, stores in r0.
Immediate operand:
ADD r0,r1,#2
Computes r1+2, stores in r0.

33. Data Processing Manipulate data within registers MOVE instructions
Arithmetic instructions
Logical instructions
Comparison instructions
Suffix S on data processing instructions updates flags in CPSR

34. Data Processing Instructions
Operands are 32-bit wide; come from registers or specified as literal (immediate operands) in the instruction itself
Second operand sent to ALU via barrel shifter
32-bit result placed in register; long multiply instruction produces 64 bit result

35. Move instruction MOV Rd, N MVN Rd, N Rd: destination register
N: can be an immediate value or source register
Example: mov r7, r5
MVN Rd, N
Move into Rd not (inverse) of the 32-bit value from source

36. Using Barrel Shifter
Enables shifting 32-bit operand in one of the source registers left or right by a specific number of positions
Basic Barrel shifter operations
Shift left, shift right, rotate right
Facilitates fast multiply, division and increases code density
Example: mov r7, r5, LSL # 2
Multiplies content of r5 by 4 and puts result in r7

37. Using Barrel Shifter

38. Barrel Shift Instructions
LSL, LSR : logical shift left/right
fills with zeroes.
ASL, ASR : arithmetic shift left/right
fills with ones.
ROR : rotate right
RRX : rotate right extended with C
performs 33-bit rotate, including C bit from CPSR above sign bit.

39. Barrel Shift with Carry

40. Arithmetic Instructions
Implements 32 bit addition and subtraction
3-operand form
Examples
SUB r0, r1, r2
Subtract value stored in r2 from that of r1 and store in r0
SUBS r1, r1, #1
Subtract 1 from r1 and store result in r1 and update Z and C flags

41. Arithmetic Instructions
ADD
add
SUB
subtract
MUL, MLA
multiply (and accumulate)

42. Multiply Instructions
Multiply contents of a pair of registers
Long multiply generates 64 bit result
Examples:
MUL r0, r1, r2
Contents of r1 and r2 multiplied and put in r0
UMULL r0, r1, r2, r3
Unsigned multiply with result stored in r0 and r1

43. Multiply and Accumulate
Result of multiplication can be accumulated with content of another register
MLA Rd, Rm, Rs, Rn
Rd = (Rm * Rs) + Rn

44. Logical Instructions
Bit-wise logical operations on the two source registers
Operators: AND, OR, EOR (Ex-OR), BIC (bit clear)
Example: BIC r0, r1, r2
r2 contains a binary pattern where every binary 1 in r2 clears a corresponding bit location in register r1
Useful in manipulating status flags and interrupt masks

45. With Barrel Shifter
Use of barrel shifter with arithmetic and logical instructions increases the set of possible available operations
Example:
ADD r0, r1, r1 LSL # 1
Register r1 is shifted to the left by 1, then it is added with r1 and the result (3 times r1) is stored in r0.

46. Compare Instructions Enables comparison of 32 bit values Examples
Updates CPSR flags but do not affect other registers
Examples
CMP r0, r9
Flags set as a result of r0 – r9
TEQ r0, r9
Flags set as a result r0 ex-0r r9
TST r0, r9
Flags as a result of r0 & r9

47. Compare Instructions CMP : compare TST : bit-wise test TEQ : XOR
These instructions set only the NZCV bits of CPSR.

48. Load-Store Instructions
Transfers data between memory and processor registers
Single register transfer
Data types supported are signed and unsigned words (32 bits), half-words, bytes
Multiple-register transfer
Transfer multiple registers between memory and the processor in a single instruction
Swap
Swaps content of a memory location with the contents of a register

49. Single Transfer Instructions
Load & Store data
LDR, LDRH, LDRB:
Load (word, half-word, byte)
STR, STRH, STRB
Store (word, half-word, byte)
Supports different addressing modes:
3 primary addressing modes
Preindex with writeback, Preindex, Postindex
Almost 9 derived addressing modes
Immediate, Register, Scaled register, …

50. Addressing Modes (1) LDR r0, [r1, #4]! Preindex with writeback
Updates the address base register with new address

51. Addressing Modes (2) LDR r0, [r1, #4] Preindex (Immediate Offset)
12-bit offset added to the base register

52. Addressing Modes (3) LDR r0, [r1], #4 Postindex
Updates the address register after address is used

53. Example (1) Initial: Preindexing with writeback: LDR r0, [r1, #4]!
r0 = 0x
r1 = 0x
mem32 [0x ] = 0x
mem32 [0x ] = 0x
Preindexing with writeback: LDR r0, [r1, #4]!
r0 = 0x
r1 = 0x
Preindexing: LDR r0, [r1, #4]

54. Example (2) Initial: Postindexing: LDR r0, [r1], #4 r0 = 0x00000000
mem32 [0x ] = 0x
mem32 [0x ] = 0x
Postindexing: LDR r0, [r1], #4
r0 = 0x
r1 = 0x

55. Derived Addressing Modes
Register indirect: LDR r0, [r1]
Register operation: LDR r0, [r1, -r2]
Calculated Address uses base register and another register
Scaled: LDR r0, [r1, r2, LSL #2]
Address is calculated using the base address register and a barrel shift operation

56. Example: C assignments
x = (a + b) - c;
Assembler:
ADR r4,a ; get address for a
LDR r0,[r4] ; get value of a
ADR r4,b ; get address for b, reusing r4
LDR r1,[r4] ; get value of b
ADD r3,r0,r1 ; compute a+b
ADR r4,c ; get address for c
LDR r2[r4] ; get value of c

57. C assignment, cont’d. SUB r3,r3,r2 ; complete computation of x
ADR r4,x ; get address for x
STR r3[r4] ; store value of x

58. Example: C assignment C: Assembler: y = a*(b+c);
ADR r4,b ; get address for b
LDR r0,[r4] ; get value of b
ADR r4,c ; get address for c
LDR r1,[r4] ; get value of c
ADD r2,r0,r1 ; compute partial result
ADR r4,a ; get address for a
LDR r0,[r4] ; get value of a

59. C assignment, cont’d. MUL r2,r2,r0 ; compute final value for y
ADR r4,y ; get address for y
STR r2,[r4] ; store y

60. Example: C assignment C: Assembler: z = (a << 2) | (b & 15);
ADR r4,a ; get address for a
LDR r0,[r4] ; get value of a
MOV r0,r0,LSL 2 ; perform shift
ADR r4,b ; get address for b
LDR r1,[r4] ; get value of b
AND r1,r1,#15 ; perform AND
ORR r1,r0,r1 ; perform OR

61. C assignment, cont’d. ADR r4,z ; get address for z
STR r1,[r4] ; store value for z

62. Multiple Register Transfer
Load-store multiple instructions transfer multiple register contents between memory and the processor in a single instruction
More efficient – for moving blocks of memory and saving and restoring context and stack

63. Multiple Byte Load-Store
Any subset of current bank of registers can be transferred to memory or fetched from memory
LDM
STM
Syntax:
<LDM|STM>{<cond>}<addressing mode> Rn{!},<registers>{^}
The base register Rn determines source or destination address

64. Address Modes (load-store multiple)

65. Load/Store Multiple Addressing

66. Control Flow Instructions
Branch Instructions
Conditional Branches
Conditional Execution
Branch and Link Instructions
Subroutine Return Instructions

67. Branch Instruction Branch instruction: B label
Example: B forward
Address label is stored in the instruction as a signed pc-relative offset
Conditional Branch: B<cond> label
Example: BNE loop
Branch has a condition associated with it and executed if condition codes have the correct value

68. Conditional Execution
An unusual feature of ARM instruction set is that conditional execution applies not only to branches but to all ARM instructions
Example: ADDEQ r0, r1, r2
Instruction will only be executed when the zero flag is set to 1

69. Thumb
Thumb encodes a subset of the 32 bit instruction set into a 16-bit subspace
Thumb has higher performance than ARM on a processor with a 16-bit data bus
Thumb has higher code density
For memory constrained embedded system
On average, a Thumb implementation takes 30% less memory than the equivalent ARM implementation.
(source: ARM System Developer’s Guide)

70. Thumb Instruction Decoding
Each Thumb instruction is related to a 32-bit ARM instruction.

71. ARMv5E Extensions
Extensions to facilitate signal processing operations
Supports
Signed multiply accumulate instruction
Greater flexibility and efficiency when manipulating 16 bit values for applications such as 16 bit digital audio processing.

72. Summary We have studied instruction set of ARM processors
We discussed the use of barrel shifters
We studied various addressing modes
We have examined Thumb mode of operation