1. Intro to Electric Circuits
GLAS wiring

2. Electric Circuits
Electricity: The flow of electrons. (Mobile particles, carrying charge)
Circuit: A path for electrons to flow in

3. Voltage, current, and resistance
The flow of electrons is like the flow of water
Driven by pressure (voltage)
Pressure causes flow (current)
The relationship between pressure and flow is set by the obstacles (resistance) in the flow path
For the flow to do useful work (have power), both pressure and flow must be present
Hydroelectric Dam
ga.water.usgs.gov/edu/hyhowworks.html

4. Circuit functions
In general, circuits can be thought of as combinations of:
Power Sources (battery, generator)
Loads (where power is used) (lamps, speakers, motors)
Conduction Paths (wires)
Controls (switches & knobs)
Indicators (meters, flashing lights, buzzers)

5. Voltage
Voltage is the electrical force, or "pressure", that causes current to flow in a circuit.
Voltage is the force that is pushing the electrons (like pressure pushes the water) forward.
It is measured in VOLTS (V ).
Count Alessandro Volta ( )

6. Current
Voltage
Current
Current is the movement of electrical charge - the flow of electrons through the electronic circuit. 
In our analogy, current would be the flow of water moving through the tube (wire).
Current is measured in AMPERES (AMPS, A or I).
Current is defined to flow from positive to negative voltages
Andre-Marie Ampere ( )

7. Conductors, Insulators, and Semiconductors
A conductor is a material (usually a metal such as copper) that allows electric current to pass easily.
This is opposed to an insulator (plastic, glass) which prevents the flow of electricity through it.
Semiconductors have intermediate properties which enable their conduction to be modified and controlled.

8. Resistance
Resistance is anything that causes an opposition to the flow of current in a circuit. - +
Voltage
Current
Resistance
Resistance controls the amount of voltage and current in a circuit. Everything in a circuit has a resistance (even wire). A resistor is a device designed specifically to have a constant resistance.
It is measured in OHMS (W).
Design and analysis of electronic circuits hinges on thorough understanding of the relationships between voltage, current, and resistance.

9. Quantification: Ohm’s Law
expresses the relationship between current, voltage, and resistance.  It was named after the German physicist Georg Simon Ohm ( ).
This is one of the most fundamental concepts in electronics.   Learn Ohm’s Law.  Learn it inside and out!     W

10. Ohm’s Law V is the voltage between two points (measured in volts)
I is the current flowing along a path between those two points (measured in amperes) 
R is the resistance of that path (measured in Ohms) 
Volts = Amps times Ohms

11. Electronic Schematics
Electronic circuits are drawn using schematics which use standard symbols for each type of electronic component
Voltage (Volts)
Current
Current (Amps)
Load/Resistor
(Ohms)
Circuit Schematic I + R V -
battery symbol
resistor symbol
Diode
Transistors
Capacitor

12. If in this circuit we observe a current flow of 12 amps (12A)
through the resistive load of 1 Ohm (1W), what must the battery voltage be?
V ?
V = I R
V = 12 (Amps) x 1 (Ohm)
V = 12 Volts (12V)
R = 12/12 : R = 1W 

13. I = V / R I = 12 (Volts)/ 1 (Ohm) :
If we knew the battery was supplying 12 volts, how do we predict the current through a resistive load of 1 Ohm?
I ?
I = V / R
I = 12 (Volts)/ 1 (Ohm) :
I = 12 Amps (12A)

14. R = V / I R = 10 (Volts)/ 5 (Amps) :
If we knew a 10V battery was supplying 5A of current, what must the load (resistance) be?
? W
R = V / I
10V 5
R = 10 (Volts)/ 5 (Amps) :
R = 2 Ohm (2 )

15. Electronic circuits
For electrons to flow contiusly, there must be a compete circuit in which electrons return to their source.
Think of it as a circle. The paths may split off here and there but they always rejoin the source eventually.
Evaporation
Condensation

16. Series Circuit
A series circuit is one with all the loads in a row. Like links in a chain.
There is only ONE path for the electricity to flow.
If this circuit was a string of light bulbs, and one blew out (became an open circuit), the remaining bulbs would turn off.
Circuit components in series experience the same current.

17. Parallel Circuit
A parallel circuit is one that has two or more paths for the electricity to flow – similar to a fork in a river
In other words, the loads are parallel to each other.
If the loads in this circuit were light bulbs and one blew out, current would still flow to the others.
Circuit components in parallel experience the same voltage.

18. Now you are ready for a Demo!

19. Ohm’s Law test circuit Current meter (in series with load) A Voltage
source
Load
resistor V
Voltage meter
(in parallel with load)