1. Hydrological Services Pty Ltd Heater Model TB323LP For Model TB3 Tipping Bucket Raingauge Presented By W.R. Barratt CEO Copyright

2. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Introduction (TB323LP) Latest innovation to measure snowfall Converts snow to liquid (water) Uses traditional tipping bucket raingauge Thermostatically controlled heating element Copyright

3. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Principle Of Snow Formation Large snowflakes can be formed by the collision of ice crystals within clouds (aggregation process) Smaller snowflakes are formed by the Bergeron-Findeisen process For snow to reach the ground the air temperature must be no more than 35.6 o F (2°C) Copyright

4. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Principle Of Snow Formation Contd One would expect the falling snow to melt as soon as the temperature rises above freezing, but this is not so. As the melting process begins, the air around the snowflake is cooled. The heaviest falls of snow tend to occur when the air temperature is between 32 and 35.6 o F (2°C) Copyright

5. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Principle Of Snow Formation Contd Individual ice crystals and snowflakes can be the shape of prisms, plates or stars - but all have 6 sides 12 inches (304.8 mm) of fresh fallen snow, when melted, is equivalent to 1.2 inches (30.48mm) of rainfall Copyright

6. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Features Of The TB323 LP More effective method of measuring snowfall Increase accuracy of measuring snowfall ± 2% based on the principle of the tipping bucket raingauge. Avoid freezing of gauge in cold climates. Hence, eliminates subsequent loss of precipitation records Gauge can be used for rainfall and snowfall (2 in 1) Copyright

7. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Features Of The TB323 LP Contd Immediate measure of snowfall. Hence, low volume of snowfall is detected and measured Heater unit is ON only between +14 o F (-10°C) and +40 o F (+4.5°C) DC powered for remote areas Real time data using appropriate RTUs and software Copyright

8. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Features Of The TB323 LP Contd Snow sensor which activates the heating elements inside the raingauge only when snow events occur. Duty cycle heating to reduce power after initial warm up. Total power consumption is generally reduced by the combination of the above two features Copyright Snow Sensor

9. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Specifications Ambient temperature range+158 to –40 o F (+70 to –40 o C) Preset ON temperature39.2 o F (+4 o C) Preset OFF temperature40 o F (+4.5 o C) Preset DE-ACTIVATION temperature 14 o F (-10 o C)(cuts out below this temperature) Heating elements are self limiting. Power generated50 watts (100 watts at initial 90 minute warm up) Voltage requirements12 volts AC/DC nominal Heating Current requirements4.2 amps average (40% duty cycle) (8.5 amps at initial warm up) Average Current Requirements1.44 Amps long term average. Copyright

10. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Typical Power Requirements Copyright

11. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Typical Power Requirements Contd Copyright

12. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Principle Of Operation Initial State Rainfall Only The Hydrological Services Tipping Bucket Raingauge (TB3) is recognised as the standard for measuring rainfall and precipitation in remote and unattended locations. The TB3 raingauge operates on the tipping bucket principle. A receiver of 200mm diameter collects the rainfall, which is strained by a metal gauze before being passed through the syphon to the tipping bucket measuring system. Tips of the plastic bucket occur with each 0.2mm, 0.5mm or 0.01 inch of precipitation collected. A reed switch detects these events and produces a momentary contact closure signal for: -logging in our Rainfall Data Logger -transmission by our Radio Reporting Raingauge, or -display on our Rainfall Counter Copyright

13. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Principle Of Operation Contd Snowfall State: The TB323LP kit is designed for use with the TB3 raingauge to accurately measure snowfall by converting snow into liquid. The device is basically a thermostatically controlled heating element, that raises the temperature of the interior of the raingauge, funnel and catch to avoid the freezing of the gauge in cold climates with subsequent loss of precipitation records. When the ambient temperature drops below a preset value (+ 4 o C), the snow sensor mode is activated. The heater elements remains off until snow is present in the catch area triggering the initial heating period (100% power) followed by 40% duty cycle until there is no snow remaining in the catch. At the completion of the heating cycle the unit will return to wait mode until triggered by a snow event. The system will be de- activated when temperature drops below (-10 o C) or above (+4.5 o C) nominal. This combination of duty cycle and snow sensor is designed to reduce power consumption. Copyright

14. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Experiment: The testing of the TB323LP was done in Hydrological Services environmental chamber. The environmental chamber was set at a steady temperature of –10 o C. Three heating elements were used. Two elements were placed below the funnel and the third element was placed at the base of the gauge beneath the bucket. To be more conservative in testing, Hydrological Services used shaved ice which is 3 times less dense than the water where snow is 10 times less dense than water. The raingauge funnel was loaded with shaved ice. Copyright

15. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Two insulating sleeves were used one inside the enclosure and another outside the enclosure to reduce heat loss. The tests were repeated for 2 weeks to ensure repeatability and calibration of the raingauge was maintained. The bucket tips, funnel temperatures and ambient temperatures were recorded over the period to evaluate the effectiveness of the heating and melting processes. Copyright

16. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Key to data table: Copyright

17. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Test Data: Copyright

18. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Copyright

19. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Copyright

20. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Copyright

21. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Copyright

22. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Test Data Contd Copyright

23. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Copyright End of 90 minutes warm up. Start of 40% duty cycle. Start of 90 minutes warm up. End of 40% duty cycle. Heater element turned off. The red line represents the bucket tips event vs. time GRAPH 1

24. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Copyright Normal behaviour of bucket tips GRAPH 2

25. Issue1: 6/10/2004Hydrological Services Pty Ltd, Sydney, Australia Future Directions All operating parameters used by the Micro- processor controlled TB323LP are factory set. However, they may be adjusted by the customer using a RS232 to RS485 converter with appropriate procedure. SDI-12 comms will be shortly introduced to allow monitoring of the TB323LP heating unit as well as direct manual control or parameter modification in real-time. Copyright