1. CHAPTER 3 Dimensioning

2. DIMENSIONING COMPONENTS
Extension lines
Dimension lines (with arrowheads)
Leader lines .

3. EXTENSION LINES
indicate the location on the object’s features that are dimensioned.

4. A dimensioned drawing should provide all the information necessary for a finished product or part to be manufactured.
Dimensions are always drawn using continuous thin lines. Two projection lines indicate where the dimension starts and finishes. Projection lines do not touch the object and are drawn perpendicular to the element you are dimensioning.
                                                                                                                                                                                                       
Dimensioning

6. Types of Dimensioning Parallel Dimensioning
Parallel dimensioning consists of several dimensions originating from one projection line.

7. Superimposed Running Dimensions
Superimposed running dimensioning simplifies parallel dimensions in order to reduce the space used on a drawing. The common origin for the dimension lines is indicated by a small circle at the intersection of the first dimension .projection line.

8. Chain Dimensioning Combined Dimensions
A combined dimension uses both chain and parallel dimensioning.

9. Dimensioning of circles
(a)shows two common methods of dimensioning a circle. One method dimensions the circle between two lines projected from two diametrically opposite points. The second method dimensions the circle internally.
(b)is used when the circle is too small for the dimension to be easily read if it was placed inside the circle.

10. Dimensioning Radii
All radial dimensions are proceeded by the capital R.
shows a radius dimensioned with the centre of the radius
located on the drawing.
(b) shows how to dimension radii which do not need their
centres locating.

11. Aligned System
values read from bottom and Right side.
Unidirectional System
values read from bottom only

12. INCORRECT
CORRECT

13. Dimensioning a circular arc.

14. Recommended Practices

15. EXTENSION LINES
Leave a visible gap (≈ 1 mm) from a view and start drawing an extension line.
Extend the lines beyond the (last) dimension line 1-2 mm.
COMMON MISTAKE
Visible gap

16. Do not break the lines as they cross object lines.
EXTENSION LINES
Do not break the lines as they cross object lines.
COMMON MISTAKE
Continuous

17. DIMENSION LINES Dimension lines should not be spaced too
Close to each other and to the view.
Leave a space at least
2 times of a letter height. 16 35 11 34
Leave a space at least
1 time of a letter height.

18. DIMENSION FIGURES The height of figures is suggested to be 2.5~3 mm.
Place the numbers at about 1 mm above dimension line and between extension lines.
COMMON MISTAKE 11 34 11 34

19. DIMENSION FIGURES When there is not enough space for figure or
arrows, put it outside either of the extension lines.
Not enough space
for figures
Not enough space
for arrows
16.25
16.25 1 1 1 or

20. DIMENSION FIGURES : UNITS
The JIS and ISO standards adopt the unit of
Length dimension in millimeters without specifying a unit symbol “mm”.
Angular dimension in degree with a symbol “o”
place behind the figures (and if necessary
minutes and seconds may be used together).

21. DIMENSION FIGURES : ORIENTATION
1. Aligned method
The dimension figures are placed so that they are readable from the bottom and right side of the drawing.
2. Unidirectional method
The dimension figures are placed so that they can be read from the bottom of the drawing.
Do not use both system on the same drawing or on the same series of drawing (JIS Z8317)

22. Unidirectional method
Aligned method
Unidirectional method

23. EXAMPLE : Dimension of length using aligned method.30 30 30 30 30 30 30 30

24. EXAMPLE : Dimension of length using unidirectional method.30 30 30 30 30 30 30 30

25. EXAMPLE : Dimension of angle using aligned method.

26. EXAMPLE : Dimension of angle using unidirectional method.

27. Drawing Scales
Scale is the ratio of the linear dimension of an element of an object shown in the drawing to the real linear dimension of the same element of the object.
Actual size
Size in drawing 1 2

28. Drawing Scales Designation of a scale consist of the “SCALE”
followed by the indication of its ratio, as follow
SCALE 1:1 for full size
SCALE X:1 for enlargement scales (x>1)
SCALE 1:X for reduction scales (x>1)
Dimension numbers shown in the drawing are correspond to “true size” of the object and they are independent of the scale used in creating that drawing

30. Thank You