1. Lineation
Lineation is expressed by the parallelism of some directional property in the rock.
Lineation is found to develop in igneous, sedimentary and metamorphic rocks. Lineations are of two types, viz.,
 primary lineation
 sedimentary rocks, igneous rocks
 secondary lineation
 metamorphic rocks
Primary lineations are those formed at the time of rock formation. It is found both in sedimentary and igneous rocks. Some varities found in sedimentary rocks may be used to tell top and bottom of beds, some may be used to tell the direction of transport of sediments, and some may be used for both purposes.
In igneous rocks both intrusive and extrusive, it may be used to tell the direction in which magma was flowing or ash flows were moving.

2. Lineation
Secondary lineations are those that formed in rocks some times after they were originally deposited, erupted or intruded. The time lapse may be short or long. Moreover, secondary lineation may be imposed on rocks more than once, so that several differently oriented lineations may be present in rock.
All transitions exist between rocks that possess no lineation and rocks with excellent lineation. In one rock the long axes of 90% of the hornblende crystals might be within a few degrees of each other; such a striking linear parallelism would be recognized immediately. In another rock, however, the long axes of the hornblende crystals might be rather evenly oriented in all possible directions within the rock; in such a case no lineation would exist.
Secondary lineation may occur with or without foliation. A rock without cleavage or schistosity may possess lineation. More commonly, however, secondary lineation is associated with foliation and lies in the plane of the foliation.

3. Horizontal lineation striking NE Vertical lineation striking NE
Attitude
The attitude of lineation is measured by its bearing and plunge or inclination. The bearing is the azimuth of the horizontal projection of the lineation, whereas the plunge is the angle between the horizontal line and lineation measured in the vertical plane.
The symbols for lineation may be shown independently of foliation or bedding. It may also be shown in combination with bedding or foliation symbols. Lowercase letters may be used to indicate the kind of lineation, such as p for pebble, h for hornblende, c for crinkles, etc..
220
Lineation plunging 220 W
Horizontal lineation striking NE
Vertical lineation striking NE
500
400
Bedding striking N450E, dipping 500NW
Lineation plunging 400N
Horizontal foliation with horizontal lineation striking N450E
220
Foliation striking N450E, dipping 300NW
Lineation plunging 220W
Vertical foliation striking N450E,
Lineation plunging 350SW

4. Kinds of Secondary Lineation
Lineations are of different kinds, these are as follows:-
1. Lineation given by minor fold axes
2. Lineation given by elongated or stretched pebbles
3. Mineral lineation
4. Lineation given by corrugations or crinkles
5. Lineation given by the intersection of “S” planes
6. Lineation given by slickensides
7. Lineation given by boudin line
8. Lineation given by quartz rod
9. Lineation given by mullion

5. 1. Lineation given by minor fold axes
Types of Lineation
Description
1. Lineation given by minor fold axes
Fold axes are commonly considered to be lineation. In metamorphic terrain the fold axes of minor folds exhibit parallel arrangement. In fact, the attitude of the fold axes is often the reference to which other lineations are compared.

6. 2. Lineation given by elongated or stretched pebbles
Types of Lineation
Description
2. Lineation given by elongated or stretched pebbles
Elongated or stretched pebbles, which are irregular ellipsoids, are associated with a foliation. The shortest axes of the pebbles are perpendicular to this foliation. The intermediate and long axes lie in the plane of foliation. The parallelism of the long axes of the pebbles produces the lineation.

7. Description 3. Mineral lineation
Types of Lineation
Description
3. Mineral lineation
Parallel linear orientation of individual minerals is very common in deformed metamorphic rocks. Lineation of this type are usually called mineral lineations. Lineation is more commonly expressed by the minerals constituting the rock. Hornblende crystals, which have one long dimension, with the result that individual crystals are more or less needle – shaped, may display an excellent lineation. In some instances, biotite occurs as elliptical plates, the long axes of which are parallel. In other instances, an original, more or less spherical mineral may be granulated into numerous fragments which become strung out into an ellipsoidal group.

8. Types of Lineation

9. Types of Lineation

10. 4. Lineation given by corrugations or crinkles
Types of Lineation
Description
4. Lineation given by corrugations or crinkles
The schistosity or cleavage may be thrown into small corrugations or crinkles, with a wave length and amplitude that are measured in millimeters. The axes of the crinkles give the lineation.

11. 5. Lineation given by the intersection of “S” planes
Types of Lineation
Description
5. Lineation given by the intersection of “S” planes
The intersection of different “S” planes produces a lineation, because the intersection of two planes is a line. If the rock breaks parallel to the cleavage, the trace of the bedding appears as parallel streaks on the cleavage plane.

13. 6. Lineation given by slickensides
Types of Lineation
Description
6. Lineation given by slickensides
Slikensides are a type of lineation. In some cases the scratches may be very obvious and clearly indicate the direction of movement. At other places a streaking caused by concentration of dark minerals along certain lines may be caused by sliding of layers past one another.

14. 7. Lineation given by boudin line
Types of Lineation
Description
7. Lineation given by boudin line
Boudinage, or sausage structure results from stretching of competent bed that thickens and thins in such a way as to simulate a string of sausages. Parallel to the bedding the individual units look like sausages lying side by side. The line of junction of the individual units is called boudin line and is a lineation.
The boudin line may be occupied by quartz, feldspar, or some other mineral. Boudinage is clearly the result of stretching at right angles to the boudin line. The more brittle bed shows boudinage.

15. 8. Lineation given by quartz rod
Types of Lineation
Description
8. Lineation given by quartz rod
Quartz rods are found in some areas of metamorphosed rocks. In their extreme development they are long cylindrical rods of quartz. A complete study of their evolution shows that in their simplest form they are small concordant veins of quartz that may have been derived from silica secreted from the country rock. However, as the individual veins become more irregular and discontinuous, they assume forms not unlike those of boudins, but far more irregular; many are rod like.

16. 9. Lineation given by mullion
Types of Lineation
Description
9. Lineation given by mullion
Mullion structure consists of a series of parallel columns. Each column may be several inches in diameter and several feet long. Each column is composed folded sedimentary or metamorphic rocks.