Presentation is loading. Please wait.

Presentation is loading. Please wait.

Lecture 28 OUTLINE The BJT (cont’d) Small-signal model

Similar presentations


Presentation on theme: "Lecture 28 OUTLINE The BJT (cont’d) Small-signal model"— Presentation transcript:

1 Lecture 28 OUTLINE The BJT (cont’d) Small-signal model
Cutoff frequency Transient (switching) response Reading: Pierret 12; Hu

2 Small-Signal Model Common-emitter configuration, forward-active mode:
R. F. Pierret, Semiconductor Device Fundamentals, Fig.12.1(a) “hybrid pi” BJT small signal model: Transconductance: EE130/230A Fall 2013 Lecture 28, Slide 2

3 Small-Signal Model (cont.)
where QF is the magnitude of minority-carrier charge stored in the base and emitter regions forward transit time EE130/230A Fall 2013 Lecture 28, Slide 3

4 Example A BJT is biased at IC = 1 mA and VCE = 3V. bdc = 90, tF = 5ps, T = 300K. Find (a) gm , (b) rp , (c) Cp . Solution: (a) (b) rp = bdc / gm = 90/0.039 = 2.3 kW (c) EE130/230A Fall 2013 Lecture 28, Slide 4

5 Cutoff Frequency, fT The cutoff frequency is defined to be the frequency (f = w/2p) at which the short-circuit a.c. current gain equals 1: EE130/230A Fall 2013 Lecture 28, Slide 5

6 fT is commonly used as a metric for the speed of a BJT.
For the full BJT equivalent circuit: fT is commonly used as a metric for the speed of a BJT. Si/SiGe HBT by IBM To maximize fT: increase IC minimize CJ,BE, CJ,BC minimize re, rc minimize tF EE130/230A Fall 2013 Lecture 28, Slide 6

7 Base Widening at High IC: Kirk Effect
For a NPN BJT: At very high current densities (>0.5mA/mm2), the density of mobile charge passing through the collector depletion region exceeds the ionized dopant charge density: increasing IC  The base width (W) is effectively increased (referred to as “base push out”)  tF increases and hence fT decreases. This effect can be avoided by increasing NC  increased CJ,BC , decreased VCE0 EE130/230A Fall 2013 Lecture 28, Slide 7 C. C. Hu, Modern Semiconductor Devices for Integrated Circuits, Figure 8-18

8 Summary: BJT Small Signal Model
Hybrid pi model for the common-emitter configuration, forward-active mode: EE130/230A Fall 2013 Lecture 28, Slide 8

9 BJT Switching - Qualitative
R. F. Pierret, Semiconductor Device Fundamentals, Figs EE130/230A Fall 2013 Lecture 28, Slide 9

10 Turn-on Transient Response
The general solution is: Initial condition: QB(0)=0 since transistor is in cutoff where IBB=VS/RS EE130/230A Fall 2013 Lecture 28, Slide 10 R. F. Pierret, Semiconductor Device Fundamentals, Fig. 12.5

11 Turn-off Transient Response
The general solution is: Initial condition: QB(0)=IBBtB EE130/230A Fall 2013 Lecture 28, Slide 11 R. F. Pierret, Semiconductor Device Fundamentals, Fig. 12.5

12 Reducing tB for Faster Turn-Off
The speed at which a BJT is turned off is dependent on the amount of excess minority-carrier charge stored in the base, QB, and also the recombination lifetime, tB. By reducing tB, the carrier removal rate is increased Example: Add recombination centers (Au atoms) in the base EE130/230A Fall 2013 Lecture 28, Slide 12

13 Schottky-Clamped BJT When the BJT enters the saturation mode, the Schottky diode begins to conduct and “clamps” the C-B junction voltage at a relatively low positive value.  reduced stored charge in quasi-neutral base EE130/230A Fall 2013 Lecture 28, Slide 13 R. F. Pierret, Semiconductor Device Fundamentals, Fig. 12.7


Download ppt "Lecture 28 OUTLINE The BJT (cont’d) Small-signal model"

Similar presentations


Ads by Google