1. Alternate Views

2. Learning Objectives Be ale to read and create section views.
Full
Half
Offset
Be able to read and create offset views.
Be able to read and create detail views.

3. Presentation Name
Course Name
Unit # – Lesson #.# – Lesson Name
Alternate Views
In some cases, orthogonal projections and pictorials are not sufficient to specify all the details of a part.
Section View. Used to show “inside” details not apparent on the exterior of the part
Auxiliary View. Used to show features that are located on an inclined surface in true size and shape
Detail View. Used to show a “close-up” view of features that are too small to adequately specify in another view

4. Section View Provides a view of an object as if it were cut by a saw
Location is indicated by a cutting plane line on another view
Cutting plane line

5. Section View Cutting plane line Indicates location of the cut
Thick and broken line
Arrows indicate direction of view
Labeled with a letter for identification on drawing
Cutting plane line

6. Section View Section lines
Hatch lines that indicate material that was “cut” at the cutting plane line
Thin lines
Section lines
Cutting plane line

7. Section Lining 45 degree angle lines should be used.
1/8” between lines.
All lines should be uniformly spaced
Thin sections may be blackened in completely
Spacing lines by eye increases speed

8. Section Lining – Line Placement
Lines should never be parallel or perpendicular to the object lines.
If the outline of the object has 45 degree lines, 30 or 60 degree lines should be used.
Assemblies with several parts should be lined with varying angle section lines.

9. Section Lining – Line Placement

10. Section View
Types
Full Section
Half Section
Offset Section

11. Full Section Cutting plane line passes fully through the part
The part of the object behind the cutting plane line (away from the direction of the arrows) is removed

12. Full Section

13. Replacing the view

14. Full Section Example
Section lines indicate material that is cut by the cutting plane line
Imagine the part is cut at cutting plane line
Direction of View
This half of the part is removed

15. Full Section Example
Section lines indicate material that is cut by the cutting plane line
Imagine the part is cut at cutting plane line
Direction of View
This half of the part is removed

16. Half Section
Used on symmetrical parts to show inside as well as outside details in one view
One quarter of the part is cut away
Cutting plane line goes halfway through the part

17. Half Section Example Half Section
Only one arrowhead in the direction of view
Note that the cutting plane line cuts away a quarter of the part
Half Section

18. Offset Section
Interior features not in line with each other can be shown in an offset section view
Note how the cutting plane line changes direction and follows the center of each feature

19. Offset Section Example

20. Presentation Name
Course Name
Unit # – Lesson #.# – Lesson Name
Auxiliary Views
Orthographic projection of an inclined plane (angled surface) which appears foreshortened in a principle orthographic projection
Used to show the true size and shape of an inclined plane and the features on it

21. Auxiliary Views
Foreshortened surfaces do not give a clear or accurate representation of the size or shape of the surface or features and should not be dimensioned
foreshortened face
TOP
FRONT
RIGHT SIDE

22. Presentation Name
Course Name
Unit # – Lesson #.# – Lesson Name
Auxiliary Views
An auxiliary view allows the viewer to look perpendicular to an angled surface to witness the true size and shape of that surface and its features (a hole in this example).
True Height
Auxiliary Distance
TOP
We will not use auxiliary views in this unit, but they will be presented in more detail in Unit 8.
FRONT
RIGHT SIDE

23. Detail Views
An enlargement of a portion of another view to illustrate small features on a part
Not to be confused with a Detail Drawing which is any drawing that contains all the information needed to manufacture a part

24. Detail View Example
A feature is broken out and enlarged for clarity

25. Applying Section Views
Worksheet 7.2
Use a straight edge for accuracy
1-3 Complete the section view on the paper
4) Assuming a ¼” grid, create one of the parts in Inventor and turn it in as Yourname7-2