1. Part III Forming and Shaping Processes and Equipment

2. FIGURE III.1 Formed and shaped parts in a typical automobile.

3. TYPICAL PRODUCTS plates sheet metal for car bodies containers foil for packaging I-beams Railroad rails seamless pipes and tubes threaded components

4. TABLE III.1 General Characteristics of Forming and Shaping Processes

5. Chapter 13 Metal-Rolling Processes and Equipment

6. ROLLING is the process of reducing the thickness of a work piece by compressive forces applied through a set of rolls aluminum beverage cans are made from sheets 0.28 mm and become 0.1 mm hot rolling coarse grains change to fine grains having an increased strength and hardness cold rolling

7. FIGURE Schematic outline of various flat-rolling and shape-rolling processes. Source: Courtesy of American Iron and Steel Institute.

8. FLAT ROLLING PROCESS

9. FIGURE 13. 2 (a) Schematic illustration of the flat-rolling process
FIGURE (a) Schematic illustration of the flat-rolling process. (b) Friction forces acting on strip surfaces. (c) Roll force, F, and torque, T, acting on the rolls. The width of the strip, w, usually increases during rolling, as shown in Fig

10. ROLL ARRANGEMENTS

11. FIGURE Schematic illustration of various roll arrangements: (a) Two-high mill; if a two-high mill is used for thick but short workpieces, it will commonly roll a billet back and forth in multiple passes, known as a reversing mill. (b) Three-high mill with elevator for multiple passes. (c) Four-high rolling mill showing various features; the stiffness of the housing, the rolls, and the roll bearings are all important in controlling and maintaining the thickness of the rolled strip. (d) Tandem rolling, with three stands. (e) Planetary mill, and (f) Cluster mill, also known as a Sendzimir or Z-mill.

12. METHODS FOR REDUCING ROLL FORCES 1. Using smaller diameter rolls 2
METHODS FOR REDUCING ROLL FORCES 1. Using smaller diameter rolls 2. taking smaller reductions per pass 3. rolling at elevated temperature to decrease strength of the material 4. applying tension to the strip to reduce the roll pressure 5. reducing friction at the roll-work piece interface

13. Roll forces tend to bend the rolls So to decrease the effect of roll forces, the rolls are ground such that their diameter at the center is slightly larger than that at their edges (camber)

14. FIGURE (a) Bending of straight cylindrical rolls caused by roll forces. (b) Bending of rolls ground with camber, producing a strip with uniform thickness through the strip width. (Roll deflections have been exaggerated for clarity.)

15. SPREADING occurs when width to thickness ratio is small

16. FIGURE Spreading in flat rolling; note that similar spreading can be observed when dough is rolled with a rolling pin.

17. FIGURE Changes in the grain structure of cast or of large-grain wrought metals during hot rolling. Hot rolling is an effective way to reduce grain size in metals for improved strength and ductility; cast structures of ingots or continuous casting (Section 5.4) are converted to a wrought structure by hot working.

18. Both sides of an aluminum foil do not have the same luster: one is shiny and the other is matte. This is because it is produced by pack rolling, where two strips are rolled at the same time to increase productivity. The foil to foil surfaces have a matte finish To improve flatness the rolled strip passes through a series of leveling rolls. The sheet is flexed in several direction

19. FIGURE 13. 7 (a) A method of roller leveling to flatten rolled sheets
FIGURE (a) A method of roller leveling to flatten rolled sheets. (b) Roller leveling to straighten drawn rods.

20. DEFECTS IN ROLLED SHEETS 1
DEFECTS IN ROLLED SHEETS 1. Wavy edges: the strip is thinner at the edges than at the . This is due to roll bending 2. cracks due to low material ductility at the rolling temperature 3. alligatoring caused by non-uniform bulk deformation of the billet during rolling or by the presence of defects in the original cast material

21. FIGURE Schematic illustration of typical defects in flat rolling: (a) wavy edges; (b) zipper cracks in the center of the strip; (c) edge cracks; and (d) alligatoring.

22. RESIDUAL STRESSES small diameter of roll or small reductions in thickness: metal is deformed to a higher degree at its surface than in its bulk, resulting in a compressive residual stress on the surface and tensile stresses in the bulk large diameter rolls or high reductions per pass tend to deform the bulk more than its surfaces

23. FIGURE (a) Residual stresses developed in rolling with small-diameter rolls or at small reductions in thickness per pass. (b) Residual stresses developed in rolling with large-diameter rolls or at high reductions per pass; note the reversal of the residual stress patterns.

24. FIGURE 13.11 An example of a tandem-rolling operation.

25. FIGURE 13. 12 Steps in the shape rolling of an I-beam
FIGURE Steps in the shape rolling of an I-beam. Various other structural sections, such as channels and rails, also are rolled by this process.

26. ROLL FORGING A round bar is shaped by passing it through a pair of rolls with specially profiled grooves

27. FIGURE Two examples of the roll-forging operation, also known as cross rolling; tapered leaf springs and knives can be made by this process. Source: After J. Holub.

28. FIGURE (a) Production of steel balls by the skew-rolling process. (b) Production of steel balls by upsetting a cylindrical blank: note the formation of flash. The balls made by these processes are subsequently ground and polished for use in ball bearings.

29. FIGURE (a) Schematic illustration of a ring-rolling operation: thickness reduction results in an increase in the part diameter. (b) through (d) Examples of cross-sections that can be formed by ring rolling.

30. FIGURE Thread-rolling processes: (a) reciprocating flat dies used to produce a threaded fastener; (b) two-roll dies; (c) rotary or planetary die set; and (d) a collection of thread-rolled parts made economically at high production rates. Source: (d) courtesy of Tesker Manufacturing Corp., Saukville, Wisconsin.

31. FIGURE 13. 17 (a) Features of a machined or rolled thread
FIGURE (a) Features of a machined or rolled thread. Grain flow in (b) machined and (c) rolled threads. Unlike machining, which cuts through the grains of the metal, the rolling of threads imparts improved strength because of cold working and favorable grain flow.

32. FIGURE Cavity formation in a solid, round bar and its utilization in the rotary tube piercing process for making seamless pipe and tubing. (See also Fig. 2.9.)

33. FIGURE Schematic illustration of various tube-rolling processes: (a) with a fixed mandrel; (b) with a floating mandrel; (c) without a mandrel; and (d) pilger rolling over a mandrel and a pair of shaped rolls. Tube diameters and thicknesses also can be changed by other processes, such as drawing, extrusion, and spinning.