1. Exercise 1
HYSYS Review
11/12/2018
Design & Analysis II

2. HYSYS Review
Using Process Simulators in Chemical Engineering A Multimedia Guide for the Core Curriculum
11/12/2018
Design & Analysis II

3. 11/12/2018
Design & Analysis II

4. Hysys Utilities Boiling Point Curves
Obtain laboratory-style distillation results for streams.
Critical Property
Calculate true and pseudo critical properties for streams.
Envelope Utility
Show critical values and phase diagrams for a stream.
Pinch Utility
Optimize the use of process heat exchange and utilities for heat exchangers,LNG's,coolers and heaters.
Property Table
Examine stream property trends over a range of conditions.
Tray Sizing
Size/rate existing sections or full towers.
Vessel Sizing
Size and cost installed Separator Unit Operations.
Pipe Sizing
Calculate the pressure drop or the pipe diameter.
Pipe Segment
Simulate a wide variety of piping situations.
11/12/2018
Design & Analysis II

5. Hysys Utilities (continued)
Boiling Point Curves
The Boiling Point Curves utility, which will generally be used in conjunction with characterized oils from the Oil Manager, allows you to obtain the results of a laboratory style analysis for your simulation streams. Simulated distillation data including TBP, ASTM D86, D86 (Corr.), D1160(Vac), D1160(Atm) and D2887 as well as critical property
data for each cut point and cold property data are calculated. The data can be viewed in tabular format or graphically.
The object for the analysis can be a stream, a phase on any stage of a tray section, or one of the phases in a separator, in a condenser or in a reboiler. You select the basis for the calculations and you can specify the boiling ranges for the simulated distillation data.
11/12/2018
Design & Analysis II

6. Hysys Utilities (continued)
Critical Property
The Critical Property Utility calculates both the true and pseudo critical temperature, pressure, volume and compressibility factor for a fully defined stream.
Before the Critical Property Utility is accessed, set up a Fluid Package using the Peng Robinson property method and the required components. Install the stream Feed.
11/12/2018
Design & Analysis II

7. Hysys Utilities (continued)
Envelope Utility
The Envelope utility allows you to examine relationships between selected parameters,for any stream of known composition,including streams with only one component. Vapor-Liquid Envelopes may be plotted for the following variables:
•Pressure-Temperature
•Pressure-Volume
•Pressure-Enthalpy
•Pressure-Entropy
•Temperature-Volume
•Temperature-Enthalpy
•Temperature-Entropy
Since the Envelope is calculated on a dry basis,you must be careful when applying the utility to multi-component mixtures that contain H 2 O or any other component which can form a second liquid phase.
Note also that the Envelope is restricted to the Peng Robinson and Soave Redlich Kwong equations of state.
11/12/2018
Design & Analysis II

8. Hysys Utilities (continued)
Pinch Utility
Pinch technology is a methodology which is used to optimize the use of process heat exchange and utilities in complicated processes. The HYSYS Pinch utility provides the necessary tools to apply the pinch principles in the design of efficient heat exchanger networks.
Property Table
The Property Table utility allows you to examine property trends over a range of conditions in both tabular and graphical formats. Using a stream of known composition,you target two independent variables
and their respective ranges of interest. The range of each independent variable is distinct and can be set as either an incremental range or a selection of specific values.Next,you relate which dependent variables are to be displayed at each combination of the independent variables.
11/12/2018
Design & Analysis II

9. Hysys Utilities (continued)
Tray Sizing
With the Tray Sizing utility you can perform design and rating sizing calculations on part or all of a converged column. Packing or tray information can be specified relating to specific tower internals such as tray dimensions or packing sizes,design flooding and pressure drop
specifications.Results include tower diameter,pressure drop,flooding, tray dimensions,etc.
Vessel Sizing
The Vessel Sizing utility allows you to size and cost installed separator, tank and reactor unit operations. You can select a vertical or horizontal orientation for the separator. To obtain a more effective analysis for your vessel, changes can be made to the default parameters provided by HYSYS.
11/12/2018
Design & Analysis II

10. Hysys Utilities (continued)
Pipe Sizing
The Pipe Sizing utility allows you to calculate the Pressure drop by defining the pipe Diameter and Schedule or to size the pipe Diameter by defining the Pressure drop and Schedule.
The Pipe Sizing utility work with one or two phase stream. In the case of two phase stream it state also the flow regime.
Pipe Segment
The pipe segment is used to simulate a wide variety of piping situations ranging from single/multiphase plant piping with rigorous heat transfer estimation,to large capacity looped pipeline problems. It offers two pressure drop correlations:one developed by Gregory,Aziz
and Mandhane,and the other by Beggs and Brill. Four levels of complexity in heat transfer estimation allow you to find a solution as rigorous as required while allowing for quick generalized solutions to well-known problems.
11/12/2018
Design & Analysis II