1. Work, Energy, and Power
AP Physics B

2. Make Predictions Video 1: Which will finish first?
Video 2: Which will land the furthest?

3. Work
Work tells us how much a force or combination of forces changes the energy of a system.
Work is the bridge between force (a vector) and energy (a scalar).
F: force (N)
d : displacement (m)
: angle between force and displacement

4. Units of Work SI System: Joule (N m) British System: foot-pound
1 Joule of work is done when 1 N acts on a body moving it a distance of 1 meter
British System: foot-pound
(not used in Physics B)
cgs System: erg (dyne-cm)
Atomic Level: electron-Volt (eV)

5. Force and direction of motion both matter in defining work!
There is no work done by a force if it causes no displacement.
Forces can do positive, negative, or zero work. When an box is pushed on a flat floor, for example…
The normal force and gravity do no work, since they are perpendicular to the direction of motion.
The person pushing the box does positive work, since she is pushing in the direction of motion.
Friction does negative work, since it points opposite the direction of motion.

6. Question
If a man holds a 50 kg box at arms length for 2 hours as he stands still, how much work does he do on the box?

7. Question
If a man holds a 50 kg box at arms length for 2 hours as he walks 1 km forward, how much work does he do on the box?

8. Question
If a man lifts a 50 kg box 2.0 meters, how much work does he do on the box?

9. Sample problem
Jane uses a vine wrapped around a pulley to lift a 70-kg Tarzan to a tree house 9.0 meters above the ground.
How much work does Jane do when she lifts Tarzan?
How much work does gravity do when Jane lifts Tarzan?

10. Sample problem
A droplet of water of mass 50 mg falls at constant speed under the influence of gravity and air resistance. After the drop has fallen 1.0 km, what is the work done by
gravity?
air resistance?
What is the net work?

11. Sample problem
A father pulls his child in a little red wagon with constant speed. If the father pulls with a force of 16 N for 10.0 m, and the handle of the wagon is inclined at an angle of 60o above the horizontal, how much work does the father do on the wagon?

12. Sample problem
Joe pushes a 10-kg box and slides it across the floor at constant velocity of 3.0 m/s. The coefficient of kinetic friction between the box and floor is 0.50.
How much work does Joe do if he pushes the box for 15 meters?
How much work does friction do as Joe pushes the box?

13. Kinetic Energy Energy due to motion K = ½ m v2 Unit: Joules
K: Kinetic Energy
m: mass in kg
v: speed in m/s
Unit: Joules

14. Sample problem A 10.0 g bullet has a speed of 1.2 km/s.
What is the kinetic energy of the bullet?
What is the bullet’s kinetic energy if the speed is halved?
What is the bullet’s kinetic energy if the speed is doubled?

15. Work and Energy Work changes mechanical energy!
If an applied force does positive work on a system, it tries to increase mechanical energy.
If an applied force does negative work, it tries to decrease mechanical energy.
The two forms of mechanical energy are called potential and kinetic energy.

16. The Work-Energy Theorem
The net work due to all forces equals the change in the kinetic energy of a system.
Wnet = DK
Wnet: work due to all forces acting on an object
DK: change in kinetic energy (Kf – Ki)

17. Sample problem
An 8.0-g acorn falls from a tree and lands on the ground 10.0 m below with a speed of 11.0 m/s.
What would the speed of the acorn have been if there had been no air resistance?
Did air resistance do positive, negative or zero work on the acorn? Why?

18. Sample problem
An 8.0-g acorn falls from a tree and lands on the ground 10.0 m below with a speed of 11.0 m/s.
How much work was done by air resistance?
What was the average force of air resistance?

19. Power Power is the rate of which work is done. P = W/Dt
W: work in Joules
Dt: elapsed time in seconds
When we run upstairs, t is small so P is big.
When we walk upstairs, t is large so P is small.

20. Unit of Power SI unit for Power is the Watt. British system
1 Watt = 1 Joule/s
Named after the Scottish engineer James Watt ( ) who perfected the steam engine.
British system
horsepower
1 hp = 746 W

21. How We Buy Energy…
The kilowatt-hour is a commonly used unit by the electrical power company.
Power companies charge you by the kilowatt-hour (kWh), but this not power, it is really energy consumed.
1 kW = 1000 W
1 h = 3600 s
1 kWh = 1000J/s • 3600s = 3.6 x 106J

22. Sample problem
A man runs up the 1600 steps of the Empire State Building in 20 minutes seconds. If the height gain of each step was 0.20 m, and the man’s mass was 80.0 kg, what was his average power output during the climb? Give your answer in both watts and horsepower.

23. Sample problem
Calculate the power output of a 0.10 g fly as it walks straight up a window pane at 2.0 cm/s.

24. Force vs. Position Graphs

25. Constant force and work
F(x)
The force shown is a constant force.
W = FDr can be used to calculate the work done by this force when it moves an object from xa to xb.
The area under the curve from xa to xb can also be used to calculate the work done by the force when it moves an object from xa to xb x xa xb

26. Variable force and work
F(x)
The force shown is a variable force.
W = FDr CANNOT be used to calculate the work done by this force!
The area under the curve from xa to xb can STILL be used to calculate the work done by the force when it moves an object from xa to xb xa xb x

27. Sample Problem
How much work is done by the force shown when it acts on an object and pushes it from x = 0.25 m to x = 0.75 m?
Figure from “Physics”, James S. Walker, Prentice-Hall 2002

28. Sample Problem
How much work is done by the force shown when it acts on an object and pushes it from x = 2.0 m to x = 4.0 m?
Figure from “Physics”, James S. Walker, Prentice-Hall 2002

29. Springs
When a spring is stretched or compressed from its equilibrium position, it does negative work, since the spring pulls opposite the direction of motion.
Ws = - ½ k x2
Ws: work done by spring (J)
k: force constant of spring (N/m)
x: displacement from equilibrium (m)
The force doing the stretching does positive work equal to the magnitude of the work done by the spring.
Wapp = - Ws = ½ k x2

30. Springs: stretching m m Ws = negative area = - ½ kx2 100 -100 -200 200
100
-100
-200
200
F(N) 1 2 3 4 5
x (m) m Fs m x
Ws = negative area
= - ½ kx2 Fs
Fs = -kx (Hooke’s Law)

31. Sample problem
A spring with force constant 250 N/m is initially at its equilibrium length.
How much work must you do to stretch the spring m?
How much work must you do to compress it m?

32. Sample problem
It takes 1000 J of work to compress a certain spring 0.10 m.
What is the force constant of the spring?
To compress the spring an additional 0.10 m, does it take 1000 J, more than 1000 J, or less than 1000 J? Verify your answer with a calculation.

33. Potential energy Energy of position or configuration “Stored” energy
For gravity: Ug = mgh
m: mass
g: acceleration due to gravity
h: height above the “zero” point
For springs: Us = ½ k x2
k: spring force constant
x: displacement from equilibrium position

34. Sample problem
A diver drops to the water from a height of 20.0 m, his gravitational potential energy decreases by 12,500 J. How much does the diver weigh?

35. Sample problem
If 30.0 J of work are required to stretch a spring from a 2.00 cm elongation to a 4.00 cm elongation, how much work is needed to stretch it from a 4.00 cm elongation to a 6.00 cm elongation?

36. Force types
Forces acting on a system can be divided into two types according to how they affect potential energy.
Conservative forces can be related to potential energy changes.
Non-conservative forces cannot be related to potential energy changes.
So, how exactly do we distinguish between these two types of forces?

37. Conservative forces Work is path independent.
Work can be calculated from the starting and ending points only.
The actual path is ignored in calculations.
Work along a closed path is zero.
If the starting and ending points are the same, no work is done by the force.
Work changes potential energy.
Examples:
Gravity
Spring force
Conservation of mechanical energy holds!

38. Conservative forces and Potential energy
Wc = -U
If a conservative force does positive work on a system, potential energy is lost.
If a conservative force does negative work, potential energy is gained.
For gravity
Wg = -Ug = -(mghf – mghi)
For springs
Ws = -Us = -(½ k xf2 – ½ k xi2)

39. More on paths and conservative forces.
Figure from “Physics”, James S. Walker, Prentice-Hall 2002
Q: Assume a conservative force moves an object along the various paths. Which two works are equal?
A: W2 = W3
(path independence)
Q: Which two works, when added together, give a sum of zero?
A: W1 + W2 = 0 or
W1 + W3 = 0
(work along a closed path is zero)

40. Sample problem Figure from “Physics”, James S
Sample problem Figure from “Physics”, James S. Walker, Prentice-Hall 2002
A box is moved in the closed path shown.
How much work is done by gravity when the box is moved along the path A->B->C?
How much work is done by gravity when the box is moved along the path A->B->C->D->A?

41. Non-conservative forces
Work is path dependent.
Knowing the starting and ending points is not sufficient to calculate the work.
Work along a closed path is NOT zero.
Work changes mechanical energy.
Examples:
Friction
Drag (air resistance)
Conservation of mechanical energy does not hold!

42. Sample problem Figure from “Physics”, James S
Sample problem Figure from “Physics”, James S. Walker, Prentice-Hall 2002
A box is moved in the closed path shown.
How much work would be done by friction if the box were moved along the path A->B->C?
How much work is done by friction when the box is moved along the path A->B->C->D->A?

43. Law of Conservation of Energy
In any isolated system, the total energy remains constant.
Energy can neither be created nor destroyed, but can only be transformed from one type of energy to another.

44. Law of Conservation of Mechanical Energy
E = K + U = Constant
K: Kinetic Energy (1/2 mv2)
U: Potential Energy (gravity or spring)
E = U + K = 0
K: Change in kinetic energy
U: Change in gravitational or spring potential energy

45. Pendulum Energy ½mvmax2 = mgh K1 + U1 = K2 + U2
For minimum and maximum points of swing h
K1 + U1 = K2 + U2
For any points 1 and 2.

46. Pendulums and Energy Conservation
Energy goes back and forth between K and U.
At highest point, all energy is U.
As it drops, U goes to K.
At the bottom , energy is all K.

47. Sample problem
What is the speed of the pendulum bob at point B if it is released from rest at point A?
1.5 m A B
40o

48. Spring Energy K1 + U1 = K2 + U2 = E m -x m ½kxmax2 = ½mvmax2 m x All U
All U
All K
K1 + U1 = K2 + U2 = E
For any two points 1 and 2 m -x m
½kxmax2 = ½mvmax2
For maximum and minimum displacements from equilibrium m x

49. Springs and Energy Conservation
Transforms energy back and forth between K and U.
When fully stretched or extended, all energy is U.
When passing through equilibrium, all its energy is K.
At other points in its cycle, the energy is a mixture of U and K.

50. Sample problem Problem copyright “Physics”, James S
Sample problem Problem copyright “Physics”, James S. Walker, Prentice-Hall 2002
A 0.21 kg apple falls from a tree to the ground, 4.0 m below. Ignoring air resistance, determine the apple’s gravitational potential energy, U, kinetic energy, K, and total mechanical energy, E, when its height above the ground is each of the following: 4.0 m, 2.0 m, and 0.0 m. Take ground level to be the point of zero potential energy.

51. Sample problem Problem copyright “Physics”, James S
Sample problem Problem copyright “Physics”, James S. Walker, Prentice-Hall 2002
A 1.60 kg block slides with a speed of m/s on a frictionless, horizontal surface until it encounters a spring with a force constant of 902 N/m. The block comes to rest after compressing the spring 4.00 cm. Find the spring potential energy, U, the kinetic energy of the block, K, and the total mechanical energy of the system, E, for the following compressions: 0 cm, 2.00 cm, 4.00 cm.

52. Law of Conservation of Energy
E = U + K + Eint= Constant
Eint is thermal energy.
U + K +  Eint = 0
Mechanical energy may be converted to and from heat.

53. Work done by non-conservative forces
Wnet = Wc + Wnc
Net work is done by conservative and non-conservative forces
Wc = -U
Potential energy is related to conservative forces only!
Wnet = K
Kinetic energy is related to net force (work-energy theorem)
K = -U + Wnc
From substitution
Wnc = U + K = E
Nonconservative forces change mechanical energy. If nonconservative work is negative, as it often is, the mechanical energy of the system will drop.

54. Sample problem Problem copyright “Physics”, James S
Sample problem Problem copyright “Physics”, James S. Walker, Prentice-Hall 2002
Catching a wave, a 72-kg surfer starts with a speed of 1.3 m/s, drops through a height of 1.75 m, and ends with a speed of 8.2 m/s. How much non-conservative work was done on the surfer?

55. Sample problem Problem copyright “Physics”, James S
Sample problem Problem copyright “Physics”, James S. Walker, Prentice-Hall 2002
A 1.75-kg rock is released from rest at the surface of a pond 1.00 m deep. As the rock falls, a constant upward force of 4.10 N is exerted on it by water resistance. Calculate the nonconservative work, Wnc, done by the water resistance on the rock, the gravitational potential energy of the system, U, the kinetic energy of the rock, K, and the total mechanical energy of the system, E, for the following depths below the water’s surface: d = 0.00 m, d = m, d = 1.00 m. Let potential energy be zero at the bottom of the pond.