1. Prototyping with Sheet Metal

2. DISCLAIMER & USAGE
The content of this presentation is for informational purposes only and is intended for students attending Louisiana Tech University only.
The authors of this information do not make any claims as to the validity or accuracy of the information or methods presented.
Any procedures demonstrated here are potentially dangerous and could result in damage and injury.
Louisiana Tech University, its officers, employees, agents and volunteers, are not liable or responsible for any injuries, illness, damage or losses which may result from your using the materials or ideas, or from your performing the experiments or procedures depicted in this presentation.
The Living with the Lab logos should remain attached to each slide, and the work should be attributed to Louisiana Tech University.
If you do not agree, then please do not view this content.
boosting application-focused learning through student ownership of learning platforms

3. Fabricating a Name Plate
Today you will make a name plate.
Some possible dimensions are shown below – you decide.
You will be provided with a 6 inch long piece of sheet metal that is 1-inch wide.
3 in
1 in
(all pieces)
2 in
1 in

4. Tools and Supplies rivet gun lettering punches hammer 6 inch piece
of sheet metal
2 rivets
Hand punch (makes holes in sheet metal)
ruler
pen

5. Sheet Metal Brake (Bending) and Shear (Cutting)

6. Safety Checklist
Sheet metal edges are sharp and will cut you (like a knife). Avoid the sharp edges and corners.
Wear safety glasses.
Only one person at a time should use a shearing / bending machine (don’t let one person hold the workpiece and another pull down the handle). Do not remove the safety bar attachment in front of the shearing edge.
Keep hands clear of the hand punch when making holes.
No “horse play” in the lab.
Keep work area clean.
Report any unsafe working conditions and/or practices to the instructor.
Take all common sense precautions. If you have an accident, report it immediately to the instructor.

7. Lay Out Your Workpiece
Use your ruler and pen to make marks on your workpiece:
Mark the location for shearing (cutting) the metal.
Mark the location for bending the metal.
Make a line to mark the bottom of your letters and the center of your name plate.

8. Class Structure – The Aim is for All to Finish
It will take the longest amount of time to punch your name into the metal.
Each group should take turns punching their names.
Each group should use only one punch kit (do not share punch kits between groups since the letters will get mixed up).
When the shearing / bending machine becomes available, go over and do your shearing and bending.
You can do the shearing / bending first, or you can punch your name first.
There is one hand punch for making holes for every two teams.

9. Punching Your Name into Plate
Start with the center letter and move to the edges (for centering).
DO NOT punch on the countertops or on your tables – it will damage them. Use the vise anvil.
Two firm strokes of the hammer on the punch creates a visible impression.

10. Straighten Your Name Plate
The plate will become bent when imprinting your name. Straighten it in the vise when finished.

11. Shear Your Strip
Slowly pull down handle until the shear contacts the metal. Then provide a stronger force to the shear handle to complete the cut.
workpiece under shearing edge
shearing edge in contact with workpiece
guard (do not remove)

12. Bend Your Strip
Move control handle until your piece is bent to the desired angle.

13. Punch Rivet Hole #1
Position your name plate and the stand together and tighten up in the vise. Then, punch the first hole (through both pieces). You will need to open the hand punch all the way back open so you can remove the punch.

14. Install Rivet #1
Position your name plate and the stand together and tighten up in the vise. Then, punch the first hole (through both pieces). You will need to open the hand punch all the way back open so you can remove the punch.
insert rivet all the
way into gun
you don’t want this part to show
Open and close handles repeatedly to draw the mandrel into the rivet. The mandrel will snap off when the two pieces are joined tightly.
Insert until head is flush with workpiece
blind rivet (pop rivet)

15. Punch Rivet Hole #2 and Install Rivet #2
You can hold the nameplate and stand by hand to punch the second hole. Then install the second rivet as before.
see next slides for applications
Congratulations!!!

16. Things Made of Sheet Metal
Servo Bracket
Lead Screw with Servo
Large Duct
Misc. Parts
Double Servo Bracket
Airplanes

17. More Types and Sizes of Rivets