Presentation is loading. Please wait.

Presentation is loading. Please wait.

Precision Dimensioning

Similar presentations


Presentation on theme: "Precision Dimensioning"— Presentation transcript:

1 Precision Dimensioning
Engineering II

2 Dimensioning Rectangular Prisms

3 Dimensioning Cylinders
The diameter of cylinders should be dimensioned in the rectangular view (not the circular view). Cylinders without a hole passing through them only require one view.

4 Dimensioning Cones

5 Dimensioning Spheres

6 Rectangular Coordinate Dimensioning
Used when computer-controlled production machines are used to manufacture parts. The designer should consult with personnel in manufacturing to ensure that the origin is located in an appropriate position. Two types of rectangular coordinate dimensioning: Coordinate Dimensioning with Dimension Lines Coordinate Dimensioning Without Dimension Lines

7 Coordinate Dimensioning with Dimension Lines

8 Coordinate Dimensioning without Dimension Lines

9 Tabular Dimensioning Tabular dimensioning is used when a series of parts consists of the same features or geometry but vary in dimension. Letters are used in place of dimension values, and the values are then placed in a table. Most standard parts are dimensioned this way in catalogs, the machinery handbook, and in the back of most textbooks.

10 Tabular Dimensioning

11 Dual Dimensioning – Position Method
Millimeter value is placed above (or below) the inch value or separated by a dash.

12 Dual Dimensioning – Bracket Method
Millimeter value is enclosed in square brackets. A note should be placed on the drawing such as: DIMENSIONS IN [ ] ARE MILLIMETERS.

13 Tolerance Dimensioning
Why do we need tolerance dimensioning? Interchangeable parts manufacturing Parts are manufactured at widely separate localities Effective size control Modern industry relies on it for subcontracting and replacement parts Accuracy is Expensive, however

14 Reading Dimensions .1 One tenth of an inch .01
One hundredth of an inch .001 One thousandth of an inch .0001 One ten-thousandth of an inch .00001 One millionth of an inch

15 Specification of Tolerances
Limit Dimension Bilateral-Equal Unilateral Bilateral-Unequal

16 Tolerance Tolerance is the total amount a specific dimension is permitted to vary (difference between the maximum and minimum limits). The dimension below has a tolerance of

17 Maximum Material Condition
When specifying tolerance dimensions, the maximum material condition (MMC) means the product or part contains the maximum amount of material specified by the tolerance. The heaviest part.

18 Maximum Material Condition
For the part shown here the MMC is since that size would yield the most material.

19 Allowance Allowance is the minimum clearance or maximum interference intended between the maximum material condition (MMC) of mating parts. The allowance for the system below is: = 0.110

20 More Terminology Nominal Size - General identification in fractions (ex. 1-1/2 for 1.500). Basic Size - General identification in decimal (ex ). Actual Size - Measured size. Limits - Maximum and minimum sizes indicated by the tolerance dimensions.

21 Clearance Fit Space is always left between parts.
What is the allowance in this case? – = .0012

22 Interference Fit Always an interference of material.
What is the allowance in this case? – = or just .0013

23 Transition Fit Fit might result in clearance or interference.

24 Line Fit Clearance or surface contact may result at assembly.

25 Basic Hole System (Hole Basis)
The minimum size hole is taken as the basic size.  Used when standard tools are used to produce holes (reamers & broaches).

26 Basic Shaft System (Shaft Basis)
The maximum shaft size is taken as the basic size.  When several parts having different fits, but one nominal size are required on a single shaft.

27 Specifying a Fit - Inches
Nominal Size Range Inches Over To Class RC 1 Limits of Clear. Standard Hole H5 Shaft g4 0-0.12 0.1 0.45 +0.2 –0 –0.1 –0.25 0.15 0.5 –0.15 –0.3 0.2 0.6 +0.25 –0.2 –0.35 0.25 0.75 +0.3 –0.45 0.3 0.95 +0.4 –0.55 0.4 1.1 –0.4 –0.7 Determine type of fit and find corresponding table Determine basic size Find size range on table Determine tolerances for Hole and Shaft Remember values are in thousandths of an inch.

28 Specifying a Fit - Inches
Nominal Size Range Inches Over To Class RC 1 Limits of Clear. Standard Hole H5 Shaft g4 0-0.12 0.1 0.45 +0.2 –0 –0.1 –0.25 0.15 0.5 –0.15 –0.3 0.2 0.6 +0.25 –0.2 –0.35 0.25 0.75 +0.3 –0.45 0.3 0.95 +0.4 –0.55 0.4 1.1 –0.4 –0.7 RC1 - Close Sliding Fit Basic size of 1.500 Upper tolerance on hole is +0.4, which is really Lower tolerance on hole is -0. Upper tolerance on shaft is Lower tolerance on shaft is

29 Specifying a Fit - Inches
Nominal Size Range Inches Over To Class RC 1 Limits of Clear. Standard Hole H5 Shaft g4 0-0.12 0.1 0.45 +0.2 –0 –0.1 –0.25 0.15 0.5 –0.15 –0.3 0.2 0.6 +0.25 –0.2 –0.35 0.25 0.75 +0.3 –0.45 0.3 0.95 +0.4 –0.55 0.4 1.1 –0.4 –0.7

30 Specifying Fits - Metric
Basic Size Loose Running Hole H11 Shaft c11 Fit 1 Max Min 1.060 0.940 0.880 0.180 0.060 20 Max 20.130 20.000 19.890 19.760 0.370 0.110 25 Max 25.130 25.000 24.890 24.760 Determine type of fit and find corresponding table Determine basic size Find size range on table Determine tolerances for Hole and Shaft

31 Specifying Fits - Metric
Basic Size Loose Running Hole H11 Shaft c11 Fit 1 Max Min 1.060 0.940 0.880 0.180 0.060 20 Max 20.130 20.000 19.890 19.760 0.370 0.110 25 Max 25.130 25.000 24.890 24.760 Loose Running Fit Basic size of 25


Download ppt "Precision Dimensioning"

Similar presentations


Ads by Google