1. Introduction to SolidWorks

2. DISCLAIMER & USAGE
The content of this presentation is for informational purposes only and is intended for students attending Louisiana Tech University only.
The authors of this information do not make any claims as to the validity or accuracy of the information or methods presented.
Any procedures demonstrated here are potentially dangerous and could result in damage and injury.
Louisiana Tech University, its officers, employees, agents and volunteers, are not liable or responsible for any injuries, illness, damage or losses which may result from your using the materials or ideas, or from your performing the experiments or procedures depicted in this presentation.
The Living with the Lab logos should remain attached to each slide, and the work should be attributed to Louisiana Tech University.
If you do not agree, then please do not view this content.
boosting application-focused learning through student ownership of learning platforms

3. Open Solidworks
Choose “Part”
Open New Document

4. SolidWorks Interface

5. Click the sketch tab to start drawing
Choose a “Plane” on which to draw your sketch

6. Notice there are different types of each
Start drawing a box
Lines or Rectangle
Notice there are different types of each
Using “Center Rectangle” you can start drawing a rectangle from the origin of the given coordinate system

7. Click “Smart Dimensions” to Set Values
Click a line to start setting its dimension.
Note: Line turns orange when hovering over it.
Drag dimension marker out form the line and click out of the dimension. The “Modify” window will appear.
Type in desired dimension and press the green check mark. Your new dimension will be set.
Tip: You can change the units in the Modify window. When a number is typed in, a drop down list for units will appear.
Repeat until all dimensions are set.
When you are done sketching and setting dimensions, press the check mark near the top left of the window.

8. Under Features, click Extruded Boss/Base to make the rectangle a box.
Type in the depth that you would like the box to be. The yellow shadow on the part gives you a preview of what it will look like.
When you are done extruding, click the green check mark near the top left.

9. Putting Holes in your box
Click the desired face. The part will change colors.
Click back into the sketch tab
Hover over the different faces of the box. Orange lines will appear indicating which face is being selected.
Click the sketch style for circle
Draw a circle anywhere on the face you chose

10. Set the dimensions of your circle using Smart Dimensions
Click the circle to set its size.
Repeat for all needed dimensions.
Click an edge and then the circle to set the distance of the circle from that edge.

11. Under Features, click Extruded Cut to make the circle become a hole
You have to tell SolidWorks what to do.
Do you want the circle to become a hole that goes through the entire block?
Do you want the circle to become a hole that only goes a set depth into the block?
Options for the hole type become available when you click this dropdown menu
When set to blind, you can set the hole to be a certain depth in this sections.
Which option do you think you would choose to make the hole go through the entire block?
Through All

12. Final part with circle cut through entire block
You can see different views of your part by clicking the View Orientation button.
Or you can put the view buttons on your taskbar for quick access.
TIP: When you click the view that the part is currently orientated to, it re-centers the part.
Click the Display Style to change the appearance of the part. Options are:
Shaded with edges
Shaded
Hidden lines removed
Hidden lines visible
Wireframe

13. Making your Part a Drawing
Click the down arrow by the new document button and choose “Make Drawing from Part/Assembly.”
Choose a view to display on the drawing. Drag and drop that view on the drawing.
You can move the views around the drawing for a cleaner layout.
A window for sheet size options pops up. Click the first option and press OK.
From the view on the drawing, you can place projections showing the other view orientations by dragging your mouse out of the view in different directions.

14. Add Dimensions on Your Drawing
Under the Annotations table click “Model Items”
Select the Source/Destination:
Entire Model
Select the type of dimensions you want to display.
Marked for drawing
Not marked for drawing
Press the green check mark.
Tip: You can move the dimensions around to make them more visible.

15. Additional SolidWorks Tips
Using a Mouse can increase functionality and help you navigate through the program more easily.
Check out the built in SolidWorks Resources.
Do the built in tutorials in SolidWorks or the Online Training.
Read through the Introducing SolidWorks PDF.
There are many helpful third party resources online
Watch videos on YouTube of people modeling parts
Search SolidWorks forums for helpful tips
Don’t be afraid to click buttons! You will learn more when you press buttons and just see what happens.