1. Detailed Baseline Design - Muons
Resistive Plate Chambers (RPCs)
Optional Technology:
Strip Scintillator/WLS fiber &
Si-Avalanche Photo-diodes
(Pixelated Photon Detectors=PPDs)

2. Institutes & Personnel
RPCs Chang-guo Lu et al., Princeton Univ. Henry Band et al., Univ. of Wisconsin Scintillator H. E. Fisk, A. Para, P. Rubinov – Fermilab D. Cauz, G. Pauletta – INFN Trieste/Udine D. Hedin, A. Dychkant – No. Illinois Univ. M. McKenna, M. Wayne – U. of Notre Dame A. Gutierrez, P. Karchin – Wayne State U.

3. SiD Muon Detector Baseline choice Detector Option
Double gap RPCs operating in avalanche mode are expected to have lowest cost and have adequate reliability
RPC and steel boundaries staggered to minimize geometric inefficiencies
> 93% eff. per layer
Digitized by KPIX(64or128)
Detector Option
MINOS style scintillating strips with SiPM readout being pursued to understand cost and performance of SiPM readout – reliable backup
3/28/10
H. Band –LCWS 10

4. SiD Muon Expected Backgrounds Detector design
Barrel -Beam halo induced muons
3 10-3/cm2- pulse train
Endcap -2γ hadrons & μ
/cm2- pulse train
Detector design
Modest resolution ~ cm
9-10 layers interspersed in steel flux return (8 λ)
X and Y coordinate readout ~ 3-4 cm pitch
3/28/10
H. Band –LCWS 10

5. Detailed Baseline Design = DBD
Critical R&D to be done by the end of 2012.
Resources: personnel, financial, material required to complete critical R&D.
Two year timeline for critical R&D.
Re-statement of baseline technology and the expected status of options.
The status of conceptual engineering.
Status of muon system simulation of performance – benchmark physics.

6. Sakue Yamada’s Nine Points
Proof of principle for critical components.
Define a feasible baseline design.
Integrate mechanical features such as cables, beam exclusion space, supports, dead zones into your DBD.
Simulation model of DBD: cooling, fault prot.
Impact on push-pull syst., assembly time, alignment, calibration demands, etc.
Impact of your DBD on the accelerator incl. IR design.
Results of simulation studies on physics quality.
1 TeV Simulation studies results.
Reliable cost estimate/contingency for your DBD.

7. RPC Goals for DBD
Summarize RPC experience in BaBar - establishing RPC aging properties as adequate for expected background rates
Study BESIII or variant RPCs as possible alternatives to traditional linseed oil design
No identified manpower to extend detector/flux return designs
No identified manpower to extend KPiX/ RPC designs
3/28/10
H. Band –LCWS 10

8. Proof of Principles - Achieved
1cm thick extruded scintillator with 1.2mm dia. WLS fiber and PPDs w/650 pixels provide adequate numbers of photo-electrons for incident beam between 0 and 6 m from readout.
Probably this factor is OK for forward/backward (x,y) strips that would be read-out at the outer radius of the circular Fe. It may be desirable to have double ended readout for barrel strips.

9. Beam in the top strip 10 cm from readout end.4 6 16 10
Top strip r.o. 2
F.P. Peds
Bottom strip r.o.
Runs and /20/2010
5/11/2018

10. Proof of Principles - Achieved
The calibration scheme during a “no –interactions” time gate allows observation of: pedestal, 1 and 2 photo-electron peaks without additional electronics and software. Such data are used to calibrate the minimum ionizing signal.
A decrease of photo-electron yield in the gap between adjacent scintillator strips implies a dead region of approximately 0.5mm, though this needs to be confirmed.

11. TB4 Set-up at D0 ; Cosmic Rays
180 digitizations * 4.708ns = 847ns . Small pulses and Large pulses!
5/11/2018

12. Muon-scintillator Channel Count
Barrel
5.7 m long; 14 barrels; axial 10, 025
(r,f) 15,570
Sum 25,595
Forward/Backw’d (x,y) Quads
RFe = 5.5 m, 4 quads X2 (x,y) [1,072]
14 planes X2 forw/back F+W 30, 016
Readout ch’s 25, ,016 = 55,611

13. R&D To Be Done
Readout end of strip needs fully integrated longitudinal, transverse and cross-sectional development that can be used to make 55K strip connections to FE electronics: mini-printed circuit plus?
Design of the electrical bias/signal cable run real estate.
Recent test beam R&D has focused on signal response to beam one strip at a time. We need to understand 16 to 64 strips in parallel.

14. More R&D to be Done
Noise measurements as the number of strips/cells increases.
Readout should not be too complicated with 16 channel boards of present electronics.
Mechanical support for strips and planes.
Extruded scintillator exists; some WLS fiber exists; will need pixelated photon detectors, etc. Cosmic ray setup?
Fool-proof alignment scheme for centering WLS fiber on pixelated photon detector and locking it in place.

15. Muons/Scintillator R&D Schedule
FY11
FY12 Q1 Q2 Q3 Q4
Muon detector drawings
Procure and bench test PPDs
Develop trigger counters
WLS to new strips
Assemble strips into plane
Additional TB4 Bds assembled
Bench tests of New TB4 boards
Bench tests of new strips
Beam tests of new strips/plane
Travelers for strips & planes*
Reports

16. Test Bench for Cosmic Testing

17. Resources (Personal, Financial, Material)
Continue with M. McKenna at Notre Dame, Paul Rubinov and Tom Fitzpatrick at Fermilab, Giovanni Pauletta, Diego Cauz and Yuri Oksuzian (Virginia Tech) and others from the Mu2e experiment have helped with running at the Fermilab Test Beam Facility (FTBF).
We will need additional TB4 style boards with more channels as are being built for other experiments.
For cost estimate we have recently updated our detector geometry file: Mu_Det_Plane_Area_7_30_2010.xls

18. Engineering Design
Effort to date has been primarily on electrical/electronics; necessary for proof of principles. Small signals vs. Noise. Rubinov’s SPICE analysis is helpful.
Mechanical engineering has been “as needed”. Now needed for modules with many strips. Mu detector impact on the Fe, e.g. cables to ..
Cost and performance depend on both mechanical and electrical designs that are well engineered. We need engineering reviews before we spend too much money.
List of Mechanical and Electrical drawings.

19. Evolution of the Muon System in the SiD Simulation
Previous SiD simulations by C. Milstene focused on finding muons in b-pair final states. We should return to these studies at some point.