1. NFC Sensor System ECE 492 - Winter 2015
Texas Instruments MSP-430FR5969
ECE Winter 2015
Eric

2. Group Members Mike Pappas Nigel Himmelreich Eric Anderson
Sensor connections to MCU and NFC
Nigel Himmelreich
NFC connection to DE0 and Bluetooth
Eric Anderson
Bluetooth-Android communication, data logging and sensor display application
Everyone reads their own

3. Functionality Inspired by a disposable ‘Smart Bandage’
Transmits real time sensor data over NFC
Inductively powered via NFC
Transfers NFC data to Bluetooth for constant monitoring via DE0
Data logging/display on Android
Eric

4. Design - Hardware
Nigel

5. Design - Sensor Connections
Mike
As of Feb 8, 2015

6. Design - Software MCU Gather sensor data
Package into NDEF (NFC data format) and send
DE0
Read from NFC and log
Send data over Bluetooth
Smartphone
Read current sensor data
Display current and past data graphically
Eric

7. Design - Sensor Software Flow Diagram
Induction power does not allow for idling
Power on -> Initialize -> Perform Read -> Power Off (lose power)
Mike

8. Design - Challenges Induction power - difficult to operate on 100μA.
Challenging antenna implementation (≃1mm x 1.8mm Schottky diodes with < 0.4V forward voltage)
NFC to DE0 communication - minimal resources available
Nigel

9. Antenna Inductance (fres~ 13.7MHz)
Design - Calculations
Antenna Design
where
a = (ri + ro)/2
b = ro – ri
ri = Inner radius of the spiral
ro = Outer radius of the spiral
N = number of turns
Antenna Inductance (fres~ 13.7MHz)
Min
Typical
Max
3.57 µH Cint = 38.5 pF)
3.85 µH Cint = 35 pF)
4.28 µH Cint = 31.5 pF)
Mike

10. Design - Components Thermal sensor and light diode TI MSP430FR5969 MCU
TI RF430CL330H NFC Module
PN532 NFC Shield
DE0 Nano
MOD-BT Bluetooth Module
Android Device
Eric

11. Code Example - RF430 Init. Mike /* From main.c */ /* From RF430.h */
// Disable the GPIO power-on default high-impedance mode
// to activate previously configured port settings
PM5CTL0 &= ~LOCKLPM5;
// Configure pins for I2C
PORT_I2C_SEL0 &= ~(SCL + SDA);
PORT_I2C_SEL1 |= SCL + SDA;
//Configure eUSCI for I2C Mode
//Set I2C mode, Master mode, sync, transmitter
UCB0CTLW0 |= UCMODE_3 + UCMST + UCSYNC + UCTR;
UCB0CTLW0 |= UCSSEL_2; // SMCLK = 8MHz
//configure pin for INTO interrupts
PORT_INTO_SEL0 &= ~INTO; // GPIO
PORT_INTO_SEL1 &= ~INTO; // GPIO
PORT_INTO_DIR &= ~INTO; // Input
PORT_INTO_OUT |= INTO; // Output high for pullup
PORT_INTO_REN |= INTO; // Internal pullup resistor
PORT_INTO_IFG &= ~INTO; // Clear interrupt flag
PORT_INTO_IES |= INTO; // Fire interrupt on high-to-low transition
// since INTO is setup active low
/* From RF430.h */
//MSP-EXP430FR5969 port definitions
//I2C
#define PORT_I2C_OUT P1OUT
#define PORT_I2C_DIR P1DIR
#define PORT_I2C_SEL0 P1SEL0
#define PORT_I2C_SEL1 P1SEL1
#define SDA BIT6
#define SCL BIT7
//INTO
#define PORT_INTO_IN P2IN
#define PORT_INTO_OUT P2OUT
#define PORT_INTO_DIR P2DIR
#define PORT_INTO_SEL0 P2SEL0
#define PORT_INTO_SEL1 P2SEL1
#define PORT_INTO_REN P2REN
#define PORT_INTO_IE P2IE
#define PORT_INTO_IES P2IES
#define PORT_INTO_IFG P2IFG
#define INTO BIT2
Mike

12. Test Plans Unit Testing Integration Testing
Test sensor data being read to MCU
Test NFC data is being sent from MCU to DE0
Test Bluetooth data from DE0 to smartphone
Verify logging ability of DE0 and smartphone
Test smartphone app and functionality
Integration Testing
Test overval data from sensors to smartphone
Verify correct data logged
Nigel

13. Optional features
Inductively power the NFC, MCU, & sensors via power from the NFC antenna when communicating with the receiving board
Add additional sensors
Join the NFC, MCU, & sensors all on one single circuit board with integrated antenna
Eric