1. Featured Flexible M2M-IoT Modem
MTX-3G-JAVA-IoT
Featured Flexible M2M-IoT Modem
MTXM2M.COM
June Rev.1.2

2. MTX-3G-JAVA-IoT MTX-3G-JAVA-IoT is a new flexible featured modem
Will replace MTX-65i and MTX-3G-JAVA family in a future
Flexible… means now we offer many options in one ordering code
Featured… new enhaced features (CAN, 2 RF cards, etc)

3. New Processor SoC has been added
-level shifter
-routing ports
-GPIO handling
-Low power modes
Internal EEPROM memory to store pulse counting

4. MTX-65i MTX-3G-JAVA MTX-3G-JAVA-IoT Standard Version
DIFFERENCES
MTX-65i MTX-3G-JAVA MTX-3G-JAVA-IoT Standard Version
DB9 – DB15 connectors position exchanged
DB9
DB15
DB9
DB15
DB9 – RS232
DB15 – RS232 plus GPIO
DB9 – RS232
DB15 – RS232 plus GPIO

5. Standard Version NO RJ connector. No Audio
Block terminal: Power and RS485
RS485
Any AC-DC adaptor (12Vdc 1Amp recommended) can be used
Block terminal
Power supply
RS485
No Audio
1 RS485 port & 2 RS232 ports. Only 2 can be active at same time

6. DIFFERENCES

7. MTX-65i MTX-3G-JAVA MTX-3G-JAVA-IoT
DIFFERENCES
MTX-65i MTX-3G-JAVA MTX-3G-JAVA-IoT
DB15
DB15

8. GPIO in detail MTX-3G-JAVA-IoT MTX-65i+G MTX-65i MTX-3G-JAVA
DIFFERENCES
GPIO in detail
MTX-3G-JAVA-IoT
2x optoisolated inputs
Can be read with AT commands or trougth microcontroller using I2C
2x optoisolated outputs
1x pulse count input (NEW)
MTX-65i
4 GPIO CMOS voltage (0—3v)
MTX-3G-JAVA
GPIO CMOS level
MTX-65i+G
2x optoisolated inputs
2x optoisolated outputs
3 LEDs
GREEN (Cellular status)
RED, BLUE configurable, controlled by micro (I2C)

9. Analog input detail MTX-3G-JAVA-IoT MTX-65i xxxx
DIFFERENCES
Analog input detail
MTX-3G-JAVA-IoT
2 analog input DIP-SWITCH configurable
AT command is not possible. Use I2C
Wider voltage range 0-50V
Current mode needs external resistor
MTX-65i xxxx
2 analog input 0—2.4V
AT command

10. Radio Frequency modules be plugged inside
Wavecard 868MHz 500mW ** **MTXTunnel firmware support
Bluetooth **
Bluetooth LE
ACCELerometer
WMBUS **
GPS **
Etc (LoRa, SigFox…)
ASC1 will not be present or functional
asc0
DB9
RS485
DB15
asc1
radio

11. New feature Watchog & periodical reset
Periodic reset. Use DIP SWITCH Nº 3.
Fixed once each 24 horas (now fixed, in future programable value) modem is switched off and on. -> Full reset
Watchdog
Not active by default
To configure and enable will need special i2C commands. Refresh it before 3 minutes (parameter now fixed, in future programable). If not refreshed, Cinterion module will be resetted.

12. Internal Battery. Battery (B) option
Different ordering code
It is possible to order almost all models with internal 1650 mA/h LiPo battery inside.
It is not needed to open MTX to plug battery. Now just close the JUMPER near SIM Card holder.
Release date TBD, planned 07/2016
5F SuperCap is also available
Options S

13. Analogue audio *********** Option A
*********** ASK!

14. New variant Opcion Power Relay P
Relay 220 VAC 6 Amp
RS485 not available

15. New variant Option CAN Bus + 1 Wire + Latch Relay
CAN bus (C option) and/or 1-Wire (1 option) have a 7-way plug-in 3.5mm pitch terminal block
The Latch Relay contacts can handle 30VDC/1A or 125VAC/0.5A

16. Software DIFFERENCES STANDALONE MODEM:
Using serial port & AT commands: high compatibility
Using USB. New drivers
Using JAVA
USB connection: Need new drivers for MES
MTX-TUNNEL: NOTHING CHANGEs. FULL compatiblity.
The BEST OPTION.
JAVA Customers. New enhaced Java JMV
-> Cinterion BGS5 or EHS6 SDK Free. Ask
-> HELP in developers.gemalto.com
-> Software guide TBD
-> Free Java source code for GPIO, I2C…
JavaTM features
 Oracle Java ME Embedded 3.2
 Compliant to CLDC 1.1 HI and IMP-NG standards
 Capable of running multiple MIDlets in parallel with inter-
MIDlet communication
 Additional Java standards APIs:
o JSR75 (FileConnection)
o JSR177 (CRYPTO)
o JSR280 (XML)
 Additional accessible periphery for Java applications
o I/O pins, I2C, SPI interfaces, ADC/DAC
o Serial interfaces (API): ASC0, ASC1, USB
 Memory space for Java applications
o Flash File System: 8MB
o RAM: 6MB
o Just-in-Time (JIT) Compiler execution optimization

17. New… MTX-TUNNEL V9
MTX-Tunnel v9 + MTX-3G-JAVA-IoT-3G can read meter counter pulses (Up to 3KHz)
2 serial ports, can read up to 3 counter pulses, 2 of them contact and another by V+
Noise & anti bounces-> Reliable readings.
Internal Datalogger, automatic data dispatch to Web/Cloud using HTTP JSON
More

18. Keep in mind MTX-65i+G MTX-65i (RS232 - RS485 Versions)
+B V7
Replaced by MTX-3G- JAVA-IoT-3G (with EHS8)
There will be not 2G + GPS * Ask for big projects
MTX-65i (RS232 - RS485 Versions)
Can be used for legacy CSD calls (metering countering)
CSD is only avaialble in MTX- 3G-JAVA-IoT-3G (EHS6 module inside).
*chipset restriction*

19. New feature: Low Power Mode (L) Option L
In this mode, all the board devices are disconnected from the power supply, except the internal coprocessor, that allows the modem to exit from this mode and go back into the normal mode. In this mode the MTX-3G-JAVA-IoT requires 100μA to supply the internal logic
Fcast 2H2016

20. ULP Feature -Ultra Low Power- (U) Option U
Modelo EOL: MTX-65i-ULP
GPIO: CMOS
Difference: GPIO optoisolated
Ultra Low Power mode
In this mode, all the board devices are disconnected from the power supply, except a little portion of
digital logic and a RTC that allows the modem to exit from this mode and go back into the normal
mode. In this mode the MTX-3G-JAVA-IoT only requires 2.5μA to supply the internal logic.
When an ULP modem enters in Ultra Low Power mode, you can wake up it again in several ways:
By optoisolated inputs (see Section 4.1.3): there are an active-high input and another active low
input allowing the modem to power up again.
By the RTC alarm: please read the MTX-3G-JAVA-IoT Family Software Manual to configure the RTC alarms
It is possible to know if the modem has been woken up by inputs or the RTC alarm by reading the
status latches
Option U includes option L
Fcast 2H2016

21. KEEP IN MIND
NOT ALL OPTIONS ARE COMPATIBLE

22. Ordering information

23. Recommended replacement
MTX-65i
MTX-3G-JAVA-IoT-2G-STD
MTX-3G-JAVA-IoT-2G-AUDIO *
MTX-65i-BAT
MTX-3G-JAVA-IoT-2G-STD-B
MTX-65i+G V6
MTX-3G-JAVA-IoT-3G/GPS-STD
MTX-65i+G+B V7
MTX-65i-RS485
MTX-65i-ULP
MTX-3G-JAVA-IoT-2G-STD-U
MTX-3G-JAVA
MTX-3G-JAVA-IoT-3G-STD
MTX-3G-JAVA-RS485
MTX-3G-JAVA-RS485-WC25
MTX-3G-JAVA-IoT-3G-STD-WC868
MTX-3G-JAVA-BAT
MTX-3G-JAVA-IoT-3G-STD-B
MTX-3G-JAVA-GPS
MTX-3G-JAVA-GPS-BAT
MTX-3G-JAVA-IoT-3G/GPS-STD-B
MTX-3G-JAVA-GPS-BT
MTX-3G-JAVA-IoT-3G/GPS-STD-BT
MTX-3G-JAVA-ULP
MTX-3G-JAVA-IoT-3G-STD-U
MTX-3G-JAVA-ULP-GPS
MTX-3G-JAVA-IoT-3G/GPS-STD-U
MTX-3G-JAVA-ULP-WC25
MTX-3G-JAVA-IoT-3G-STD-U-WC868
MTX-3G-JAVA-WC25
MTX-3G-JAVA-WC500
MTX-3G-JAVA-IoT-3G-STD-WC868-LR
MTX-3G-JAVA-BT
MTX-3G-JAVA-IoT-3G-STD-BT
MTX-3G-JAVA-BT-BAT
MTX-3G-JAVA-IoT-3G-STD-B-BT
 * MOQ

24. Roadmap 2G BGS5 WATCHDOG CONFIG UARTS RESET MODEM 24H (Microswitch)
LORA / SIGFOX
DATALOGGER CONTADORES + SUPER CAP
DATALOGGER CONTADORES + BATERIA

25. Questions, more info Sales info@mtxtm2m.com
Technical
Preliminary hardware manual ready
Web (TBD)