1. First Law of Thermodynamics applied to Flow processes

2. Control Volume & Control Surface
A control volume is a certain fixed region on which attention is focused and through which the moving substance flows.
A control surface is the surface on the control volume.

3. Steady flow process
The flow is said to be steady if the rate at which the fluid flows through a machine or piece of apparatus and the rate at which the energy changes are constant.
At the steady state of a system, any thermodynamic property will have a fixed value at a particular location, and will not alter with time. These thermodynamic property depends only on space coordinates but not on time.

4. Assumptions made in the analysis of steady flow process of a system
The mass flow through the system remains constant.
Fluid is uniform in composition.
The only interaction between the system and its surroundings are work and heat.
The state of fluid at any point remains constant with time.
In the analysis, only potential, kinetic and flow energies are considered.

5. Simple steady flow process of a system
The two governing equations are:
Mass balance equation, and
Energy balance equation

6. Notations

7. mass flow rate entering = mass flow rate leaving
Mass balance equation
By the conservation of mass, if there is no accumulation of mass within the control volume, the mass flow rate entering the system must be equal to the mass flow rate leaving the system. i.e.,
mass flow rate entering = mass flow rate leaving
This equation is known as Mass balance equation
(or) Continuity equation

8. Work transfers in steady flow processes
In the flow process, the work transfer may be an external work (or) a flow work.
The external work refers to all the work transfer across the control surface other than that due to normal fluid forces.
The only external work transfers considered in engineering thermodynamics are shear work (shaft or stirring) and electrical work.

9. Energy balance equation
Since there is no accumulation of energy, by the conservation of energy, the total rate of flow of all energy streams entering the control volume must be equal to the total rate of flow of all energy streams leaving the control volume. i.e.
Total energy flow rate entering = Total energy flow rate leaving
(or)
Considering unit mass of the substance,
This equation is known as Energy balance equation
(or) Steady Flow Energy Equation (SFEE)

10. Applications of First law applied to flow processes
Nozzle
Diffuser
Compressor
Turbine
Throttling device
Boiler
Evaporator
Condenser
Water turbine
Water pump

11. Nozzle / Diffuser
Nozzle Diffuser

12. Compressor
(or)

13. Turbine
(or)

14. Throttling device

15. Throttling curve (or) isenthalpic curve on T-P plane

16. Boiler

17. Evaporator

18. Condenser

19. Water Turbine
since

20. Water Pump

21. Problem - 1
Air flows steadily at the rate of 0.5kg/s through an air compressor, entering at 7m/s, 100kPa pressure and 0.95m3/kg volume, and leaving at 5m/s, 700kPa pressure and 0.19m3/kg volume. The internal energy of the air leaving is 90kJ/kg greater than that of air entering. Cooling water in the compressor jackets absorbs heat from the air at the rate of 58kW. (a) Compute the rate of shaft work input to the air in kW. (b) Find the ratio of the inlet and outlet pipe diameters.

22. Problem - 2
In a steam power station, steam flows steadily through a 0.2m diameter pipeline from the boiler to the turbine. At the boiler end, the steam conditions are found to be: p = 4MPa, t = 400C, h = kJ/kg and v = 0.95m3/kg. At the turbine end, the conditions are found to be: p = 3.5MPa, t = 392C, h = kJ/kg and v = 0.084m3/kg. There is a heat loss of 8.5kJ/kg from the pipeline. Calculate the steam flow rate.

23. Problem - 3
Air at a temperature of 15C passes through a heat exchanger at a velocity of 30m/s where its temperature is raised to 800C. It then enters a turbine with the same velocity of 30m/s and expands until the temperature falls to 650C. On leaving the turbine, the air is taken at a velocity of 60m/s to a nozzle where it expands until the temperature has fallen to 500C. If the air flow rate is 2kg/s, calculate (a) the rate of heat transfer to the air in the heat exchanger, (b) the power output from the turbine assuming no heat loss, and (c) the velocity at the exit of the nozzle, assuming no heat loss. Take the enthalpy of the air as h=cpt, where cp is the specific heat equal to 1.005kJ/kg and t is the temperature.

24. Problem - 4
In a gas turbine the gas enters at the rate of 5kg/s with a velocity of 50m/s and enthalpy of 900kJ/kg and leaves the turbine with a velocity of 150m/s and enthalpy of 400kJ/kg. The loss of heat from the gases to the surroundings is 25kJ/kg. Assume for gas R = 0.285kJ/kg-K and cp=1.004kJ/kg-K and the inlet conditions to be at 100kPa and 27C. Determine the power output of the turbine and the diameter of the inlet pipe.

25. Problem - 5
12kg/min of air is delivered by a centrifugal compressor. The inlet and outlet conditions are C1 = 12m/s, p1 = 1bar, v1 = 0.5m3/kg and C2 = 90m/s, p2 = 8bar, v2 = 0.14m3/kg. The increase in the enthalpy of air passing through the compressor is 150kJ/kg and heat loss to the surroundings is 700kJ/min. Find (a) motor power required to drive the compressor, and (b) ratio of inlet to outlet pipe diameters. Assume that inlet and discharge lines are at the same level.

26. Therefore maximum work obtainable is equal to
is minimum when
(or)
Therefore maximum work obtainable is equal to