1. IR OBSTACLE DETECTION TO
ACTUATE LOAD

2. Introduction
This system is used to turn on a load whenever the IR ray is blocked by
an object, person.
A 38 KHz signal is generated by 555 timer which is feed to the IR diode
which in turn produces an IR ray of 38Khz.This ray is received by tuned
IR receiver continuously.
Whenever there is an obstacle to the IR ray the receiver sends a signal
to the microcontroller which actuates a load, from its output.

3. EMBEDDED SYSTEMS Definition for :- EMBEDDED SYSTEMS
A combination of hardware and software which together
form a component of a larger machine.
An example of an embedded system is a microprocessor that
controls an automobile engine.
An embedded system is designed to run on its own without
human intervention, and may be required to respond to
events in real time.

4. EMBEDDED SYSTEMS

5. AT89S52 MICRO CONTROLLER Compatible with MCS®-51 Products
8K Bytes of In-System Programmable (ISP) Flash Memory
4.0V to 5.5V Operating Range
Crystal Frequency MHZ
Three-level Program Memory Lock
256 x 8-bit Internal RAM
32 Programmable I/O Lines
Three 16-bit Timer/Counters
Eight Interrupt Sources
Full Duplex UART Serial Channel
Watchdog Timer
AT89S52

6. PIN DIAGRAM OF AT89S52

7. BC547 The BC547 transistor is an NPN Epitaxial Silicon Transistor.
The BC547 transistor is a general-purpose transistor in small plastic packages.
It is used in general-purpose switching and amplification BC847/BC547 series 45 V, 100 mA NPN general-purpose transistors.
Whenever base is high, then current starts flowing through base and emitter and after that only current will pass from collector to emitter

8. RELAY IT IS A ELECTRO MAGNETIC SWITCH
USED TO CONTROL THE ELECTRICAL DEVICES
COPPER CORE MAGNETIC FLUX PLAYS MAIN ROLE HERE

9. 555 TIMER
The 555 Timer IC is an integrated circuit (chip) implementing a variety of timer and multivibrator applications.
The original name was the SE555 (metal can)/NE555 (plastic DIP) and the part was described as "The IC Time Machine".
Depending on the manufacturer, the standard 555 package includes over 20 transistors, 2 diodes and 15 resistorson a silicon chip installed in an 8-pin mini dual-in-line package (DIP-8)

10. PIN DIAGRAM OF 555 The 555 timer IC is a simple 8 pin DIL package IC.
It can:
be used as a monostable
be used as an astable
source or sink 100mA
use supply voltages of 5v to 15v
disrupt the power supply - use a decoupling
capacitor!

11. IR LED
An IR LED, also known as IR transmitter, is a special purpose LED that transmits infrared rays in the range of 760 nm wavelength.
Such LEDs are usually made of gallium arsenide or aluminum gallium arsenide. They, along with IR receivers, are commonly used as sensors.
The appearance is same as a common LED. Since the human eye cannot see the infrared radiations, it is not possible for a person to identify whether the IR LED is working or not, unlike a common LED.
To overcome this problem, the camera on a cell phone can be used. The camera can show us the IR rays being emanated from the IR LED in a circuit.

12. TSOP 1738 RECEIVER PIN DIAGRAM
It’s a standard IR remote control
receiver
supporting all major transmission codes
Pin1 – Connected to Ground
Pin2 – Connected to Vcc
Pin3 – Output Pin
In Between 1st Pin and 2nd Pin we have
to connect one Capacitor
TSOP 1738 Receives 14—bit of data

13. TSOP 1738 FEATURES Photo detector and preamplifier in one package
Internal filter for PCM frequency
TTL and CMOS compatibility
Output active low
Low power consumption
High immunity against ambient light
Continuous data transmission possible (up to 2400 bps)
Suitable burst length .10 cycles/burst

14. SOFTWARE REQUIREMENTS
PROGRAMMING LANGUAGES Embedded C , ALP (Assembly Language) COMPILERS: Keil 2.0/3.0uv DUMPING SOFT WARE: Using Micro controller flash Software we are dumping our HEX Code into Micro Controller

15. SCHEMATIC DIAGRAM

16. KEIL COMPILER WINDOW

17. APPLICATIONS

18. ADVANTAGES & DISADVANTAGES

19. CONCLUSION