Presentation is loading. Please wait.

Presentation is loading. Please wait.

Per-Unit System.

Similar presentations


Presentation on theme: "Per-Unit System."— Presentation transcript:

1 Per-Unit System

2 Per-Unit System Actual value Quantity per unit =
The voltages, currents, powers, impedances, and other electrical quantities are expressed by: Quantity per unit = Actual value Base value of quantity It is customary to select two base quantities to define a given per-unit system. The ones usually selected are: voltage and power.

3 Per-Unit System Assume:
Then compute base values for currents and impedances:

4 Per-Unit System And the per-unit system is: Percent of base Z

5 Example 1 An electrical lamp is rated 120 volts, 500 watts. Compute the per-unit and percent impedance of the lamp. Give the p.u. equivalent circuit. Solution: Compute lamp resistance power factor = 1.0

6 Example 1 (2) Select base quantities (3) Compute base impedance
(4) The per-unit impedance is:

7 Example 1 (5) Percent impedance: (6) Per-unit equivalent circuit:

8 Example 2 An electrical lamp is rated 120 volts, 500 watts. If the voltage applied across the lamp is twice the rated value, compute the current that flows through the lamp. Use the per-unit method. Solution:

9 Example 2 The per-unit equivalent circuit is as follows:

10 Per-unit System for 1-  Circuits
One-phase circuits where

11 Per-unit System for 1-  Circuits

12 Transformation Between Bases
Selection 1 Then Selection 2 Then

13 Transformation Between Bases
“1” – old “2” - new

14 Transformation Between Bases
Generally per-unit values given to another base can be converted to new base by by the equations: When performing calculations in a power system, every per-unit value must be converted to the same base.

15 Per-unit System for 1- Transformer
Consider the equivalent circuit of transformer referred to LV side and HV side shown below: Define (1) Referred to LV side (2) Referred to HV side

16 Per-unit System for 1- Transformer
Choose: Normal choose rated values as base values Compute:

17 Per-unit System for 1- Transformer
Per-unit impedances are: Per-unit equivalent circuits of transformer referred to LV side and HV side are identical !! So:

18 Per-unit Eq. Ckt for 1- Transformer
Fig 1. Eq Ckt referred to LV side Fig 2. Per-unit Eq Ckt referred to LV side Fig 3.

19 Per-unit Eq. Ckt for 1- Transformer
Fig 4. Eq Ckt referred to HV side Fig 5. Per-unit Eq Ckt referred to HV side Fig 6.

20 Voltage Regulation Voltage regulation is defined as:
In per-unit system: Vfull-load: Desired load voltage at full load. It may be equal to, above, or below rated voltage Vno-load: The no load voltage when the primary voltage is the desired voltage in order the secondary voltage be at its desired value at full load

21 Voltage Regulation Example
A single-phase transformer rated 200-kVA, 200/400-V, and 10% short circuit reactance. Compute the VR when the transformer is fully loaded at unity PF and rated voltage 400-V. Solution: Fig 7. Per-unit equivalent circuit

22 Voltage Regulation Example
Rated voltage:

23 Voltage Regulation Example
Secondary side: Voltage regulation:

24 Problem 1 G 20 kV 22kV/220kV 80MVA 14% 220kV/20kV 50MVA 10% 50MVA
0.8 PF lagging Select Vbase in generator circuit and Sb=100MVA, compute p.u. equivalent circuit.

25 Per-unit System for 3- Circuits
Three-phase circuits where

26 Per-unit System for 3- Circuits

27 Per-unit System for 3- Transformer
Three 25-kVA, 34500/277-V transformers connected in -Y. Short-circuit test on high voltage side: Determine the per-unit equivalent circuit of the transformer.

28 Per-unit System for 3- Transformer
(a) Using Y-equivalent

29 Per-unit System for 3- Transformer
So

30 Per-unit System for 3- Transformer
(b) Using -equivalent

31 Per-unit System for 3- Transformer
So


Download ppt "Per-Unit System."

Similar presentations


Ads by Google