實驗力學研究室 1 Entire Model verse Individual Components or Groups “Pregrouping” should not pose an inconvenience for investing a single component in an assembly,

Slides:



Advertisements
Similar presentations
FE analysis with shell and axisymmetric elements E. Tarallo, G. Mastinu POLITECNICO DI MILANO, Dipartimento di Meccanica.
Advertisements

Definition I. Beams 1. Definition
Overview of Loads ON and IN Structures / Machines
Beams and Frames.
Chapter Outline Shigley’s Mechanical Engineering Design.
Some Ideas Behind Finite Element Analysis
Chapter 17 Design Analysis using Inventor Stress Analysis Module
Lecture 2 – Finite Element Method
Copyright 2001, J.E. Akin. All rights reserved. CAD and Finite Element Analysis Most ME CAD applications require a FEA in one or more areas: –Stress Analysis.
Tutorial 2 SSMA Cee in Compression: 600S F y = 50ksi Objective To model a typical Cee stud in compression and determine the elastic critical local.
CHAPTER 7 TRANSVERSE SHEAR.
2D Analyses Mesh Refinement Structural Mechanics Displacement-based Formulations.
Bars and Beams FEM Linear Static Analysis
Copyright © 2002J. E. Akin Rice University, MEMS Dept. CAD and Finite Element Analysis Most ME CAD applications require a FEA in one or more areas: –Stress.
CM 197 Mechanics of Materials Chap 14: Stresses in Beams
Workshop A12-2 Fatigue: Strain-Life.
CHAP 4 FINITE ELEMENT ANALYSIS OF BEAMS AND FRAMES
COMPUTER-AIDED DESIGN The functionality of SolidWorks Simulation depends on which software Simulation product is used. The functionality of different producs.
AE2302 AIRCRAFT STRUCTURES-II
Ken Youssefi Mechanical Engineering Department 1 Normal & Shear components of stress Normal stress is perpendicular to the cross section,  (sigma). Shear.
Engineering Mechanics: Statics
BFC (Mechanics of Materials) Chapter 3: Stress in Beam
Principal Stresses and Strain and Theories of Failure
7.2 Shear and Moment Equations and Diagrams
SHEAR IN BEAMS. SHEAR IN BEAMS Introduction Loads applied to beams produce bending moments, shearing forces, as shown, and in some cases torques. Beams.
MAE 343-Intermediate Mechanics of Materials QUIZ No.1 - Thursday, Aug. 26, 2004 List three possible failure modes of a machine element (5points) List the.
LOGO Soil slope stability analysis combining shear strength reduction and slip line method Supervisor: Yongchang Cai Ph.D. candidate: Jie Wu School of.
LAT-TD GLAST LAT Project 1x4 Grid Lift Fixture Weld Analysis September 19, 2003 Youssef Ismail.
實驗力學研究室 1 CAD Modeling for FEA. 實驗力學研究室 2 Four typical scenarios seen in product design: CAD models prepared by the design group for eventual FEA. CAD.
Transformations of Stress and Strain
實驗力學研究室 1 Solving the Model. 實驗力學研究室 2 Multiple Load and Constraint Cases Option 1. Results from multiple load cases in a single run may be combined.
Chapter 10 Rotational Motion.
11/11/20151 Trusses. 11/11/20152 Element Formulation by Virtual Work u Use virtual work to derive element stiffness matrix based on assumed displacements.
© 2011 Autodesk Freely licensed for use by educational institutions. Reuse and changes require a note indicating that content has been modified from the.
實驗力學研究室 1 Key Elements of a Successful FEA Implementation.
Mechanics of Materials – MAE 243 (Section 002) Spring 2008 Dr. Konstantinos A. Sierros.
Frame with Cutout Random Load Fatigue. Background and Motivation A thin frame with a cutout has been identified as the critical component in a structure.
Finite Element Analysis
Second Order Analysis In the previous classes we looked at a method that determines the load corresponding to a state of bifurcation equilibrium of a perfect.
S12-1 ADM740, Section 12, June 2007 Copyright  2007 MSC.Software Corporation SECTION 12 USING FLEXIBLE BODIES.
11 10-Jan-16 Last course Interpretations and properties of the stiffness matrix (cont’d) The DSM for plane and space trusses.
COMBINED LOADING.  Analyze the stress developed in thin-walled pressure vessels  Review the stress analysis developed in previous chapters regarding.
Stress and Strain ( , 3.14) MAE 316 – Strength of Mechanical Components NC State University Department of Mechanical & Aerospace Engineering Stress.
Two loading Conditions
MAE 322 Machine Design Lecture 2
Beam Design Beams are designed to safely support the design loads.
Nonlinear Analyses of Modular Coils and Shell structure for Coil Cool-down and EM Loads Part 1 – Results of Shell Structure and Modular Coils H.M. Fan.
CAD and Finite Element Analysis Most ME CAD applications require a FEA in one or more areas: –Stress Analysis –Thermal Analysis –Structural Dynamics –Computational.
Lecture 1 Stress 16 July 2007 ENT 450 Mechanics of Materials Dr. Haftirman 1 ENT 450 MECHANICS OF MATERIALS (MoM) RC. Hibbler Lecture: DR. HAFTIRMAN Teaching.
6. Strain Assoc.Prof.Dr. Ahmet Zafer Şenalp Mechanical Engineering Department Gebze Technical University.
von Mises stress, fatigue, and failure theory
5. Torsional strength calculation. 5.1 Torsional loads acting on a ship hull.
Principal Stresses and Strain and Theories of Failure
11 Energy Methods.
11 Energy Methods.
7. Yield Criteria of Metals
Structures and Machines
Shear in Straight Members Shear Formula Shear Stresses in Beams
Transformations of Stress and Strain
Overview of Loads ON and IN Structures / Machines
CAD and Finite Element Analysis
Stresses, Strains and Deflections of Steel Beams in Pure Bending
11 Energy Methods.
Structure I Course Code: ARCH 208 Dr. Aeid A. Abdulrazeg
3 Torsion.
DEPARTMENT OF MECHANICAL AND MANUFACTURING ENGINEERING
Simple Stresses & Strain
Copyright ©2014 Pearson Education, All Rights Reserved
Yielding And Fracture Under Combine Stresses
Presentation transcript:

實驗力學研究室 1 Entire Model verse Individual Components or Groups “Pregrouping” should not pose an inconvenience for investing a single component in an assembly, given that is always good modeling practice to create separate groups for each component in assembly modeling.

實驗力學研究室 2 Types of Output Data I.Displacements In addition to the display of displacement magnitudes, you will generally be allowed to request the display of components with respect to either the global coordinate system or a user-defined coordinate system. Rotations You should be able to request the display of rotation results for nonsolid elements only. When torsional rigidity is important, such as in vehicle frame structures, these are useful quantities. Velocities and Accelerations

實驗力學研究室 3 II.Strain Quantities Max, Mid, Min Principal Strain The max principal strain is the most positive of these, the min principal is the least positive, and the mid principal has a numerical value between the former two. Normal and Shear Strain These quantities will generally be displayed relative to global coordinate system directions, although you may be given the option to select a user-defined coordinate system instead.

實驗力學研究室 4 Shell Membrane and Transverse Shear Strain Shell membrane strains refer to a biaxial strain state along the mid- plane of the shell element. This definition utilizes the local coordinate system of each element, where the Z axis is normal to the shell. Shell transverse shear strains occur along the mathematical thickness of the shell element, reported with respect to the elemental X and Y directions. Strain Energy This quantity is useful for predicting high stress areas in ductile materials, and is the basis for the derivation of the von Mises stress. For all elements, a total strain energy may be reported.

實驗力學研究室 5 For shell elements, a membrane value per unit area due to the stretching of such elements’ mid-planes may be displayed. Shell and line elements may report both bending and shear strain energies per unit length. Tensile and torsion strain energies per unit length may also be available for line elements only.

實驗力學研究室 6 III.Stress Quantities Max, Mid, Min Principal Stress Normal and Shear Stresses Von Mises Stress The von Mises stress is defined by the distortion energy theory as a combination of all principal stress, which are themselves a combination of all normal and shear stresses.

實驗力學研究室 7 IV.Reaction and Resultant Forces and Moments Analysis goals will often include determining the reaction forces and moments occurring at each model constraint. These reactions may then be used as input loads to separate models of the supporting attachments that your constraints have attempted to simulate. On other occasions you will be more interested in resultant forces that occur internally in the model. These in turn can be used to evaluate the strength of internal structural joints in assembly modeling, or as load parameters in a simplified model of a section of the original.

實驗力學研究室 8 Line Element Results 1.Strain and stress Line element strain and stress results are usually divided into axial, bending, torsional, and total by the postprocessor for display purposes. 2.Resultant Force and Moments Resultant forces can be displayed in either axial or shear components. Resultant moments may also be separated into bending and torsional.

實驗力學研究室 9 Shell Element Results For a given strain or stress state, the postprocessor must be directed as to the location along the thickness of the shell for which to report the results. The choices generally available are top, bottom, maximum, and minimum.

實驗力學研究室 10 I.Types of Results Displays II.Animation III.Fringe In reality, strain, stress, and resultant force values are continuous through the material of the structure. By comparison, due to the discretization inherent in the technology, these FEA calculated quantities are virtually never continuous across two elements. However, because these quantities should be continuous, most codes allow for averaging in fringe plots. You should nonetheless always look first at inaveraged results so that errors in the mesh are not hidden by the display.

實驗力學研究室 11 Appearing below are a few important notes on averaging. Never average between elements of different type Never average between elements of different material property Never average between shell of different thickness Never average between line elements of different cross sections

實驗力學研究室 12 III.Isolines and Isosurfaces Whereas fringe plots will color fill the areas between the limiting boundary values of each range, a contour plots will color outline the boundaries themselves.

實驗力學研究室 13 IV.Query

實驗力學研究室 14 V.Vector Plots Quantities that may be displayed with vectors include displacement, velocity, and acceleration magnitudes and their rotational equivalents, and max and min principal stresses. The most useful vector plot is arguably that of max and min principal stresses, which displays the directions of both principal quantities. This is extremely helpful in determining strain gauge placement and orientation when conducting correlation testing.

實驗力學研究室 15

實驗力學研究室 16 VI.Graphs Graphs are very useful in determining the continuity of results, and therefore, results quantity. As your solution reaches better convergence, these graphs should become smoother.

實驗力學研究室 17

實驗力學研究室 18 Results Interpretation: Quality Inspection and Verification Techniques I.Convergence Issues The first thing you must determine in FEA results interpretation is whether the solution to the analysis has converged. The quality of your results is an indication of, and depends on, this convergence criterion.

實驗力學研究室 19 II.Correlation to Expectations (Common Sense) Consult with your peers. Take a closer look at your boundary conditions, element properties, and all other assumptions. You should never continue past this point until you are convinced that what you are seeing on the screen is real. The farther you progress in FEA, the more projects you take to completion, the better tuned your common sense or engineering judgment will become. III.Qualification and Review of Assumptions Each one of your loads, constraints, properties, and modeling and solution choices carried an assumption. You should always keep a record of assumptions as you progress through the setup process.

實驗力學研究室 20 IV.Correlation to Closed Form Equations V.Use of Test Models If you are attempting to use a new modeling technique, evaluating it in a small and simple test model is much more efficient than in a full, and probably complex and resource intensive, analysis. A good rule of thumb to use with test models is “one question, one answer.” develop test models to isolate the technique or quantity of interest.

實驗力學研究室 21 VI.Correlation to Testing A guideline for correlation with FEA is that you always analyze what you test, and test what you analyze. The boundary conditions of a test fixture will often be different from those of the actual application, and this difference must be accounted for in your model. VII.Relation to Problem Goals