A certain pendulum consists of a 2

Slides:



Advertisements
Similar presentations
Wednesday, Nov. 24, 2010 PHYS , Fall 2010 Dr. Jaehoon Yu 1 PHYS 1441 – Section 002 Lecture #20 - Review Wednesday, Nov. 24, 2010 Dr. Jaehoon Yu.
Advertisements

Q07. Conservation of Energy
1997B1. A kg object moves along a straight line
A pendulum consisting of a ball of mass m is released from the position shown and strikes a block of mass M. The block slides a distance D before stopping.
R. Field 10/01/2013 University of Florida PHY 2053Page 1 Exam 1: Tomorrow 8:20-10:10pm Last NameRoom A-KCAR 100 L-RNPB 1001 S-ZTUR L007 You may bring a.
Physics 111 Practice Problem Statements 07 Potential Energy & Energy Conservation SJ 8th Ed.: Chap 7.6 – 7.8, 8.1 – 8.5 Contents: 8-4, 8-5, 8-16, 8-19*,
-PotentialEnergy -Conservation of Mechanical Energy in an isolated system, without friction. AP Physics C Mrs. Coyle.
Chapter 9:Linear Momentum 8-4 Problem Solving Using Conservation of Mechanical Energy 8-5 The Law of Conservation of Energy 8-6 Energy conservation with.
Physics 151: Lecture 16, Pg 1 Physics 151: Lecture 16 Today’s Agenda l Today’s Topics: çConservation of mechanical energy çNonconservative forces and loss.
Physics 151: Lecture 15, Pg 1 Today’s Topics l Potential Energy, Ch. 8-1 l Conservative Forces, Ch. 8-2 l Conservation of mechanical energy Ch.8-4.
Instructor: Dr. Tatiana Erukhimova
Ch Ch.15 Term 051. Ch-12  T051: Q: 16. A cube of volume 8.0 cm3 is made of material with a bulk modulus of 3.5×109 N/m2. When it is subjected.
General Physics 1, Additional questions By/ T.A. Eleyan
AP Physics Review Ch 10 – Oscillatory Motion
1a. Positive and negative work
Example: The simple pendulum l Suppose we release a mass m from rest a distance h 1 above its lowest possible point. ç What is the maximum speed of the.
T101Q7. A spring is compressed a distance of h = 9.80 cm from its relaxed position and a 2.00 kg block is put on top of it (Figure 3). What is the maximum.
Work and Energy Definition of Work Kinetic Energy Potential Energy
Classical Mechanics Review 4: Units 1-19
Dynamics II Motion in a Plane
Potential Energy and Conservative Forces
Chapter 8 - Potential Energy and Conservation of Energy Conservative vs. Non-conservative Forces Definition of Potential Energy Conservation Of Mechanical.
Physics 215 – Fall 2014Lecture Welcome back to Physics 215 Today’s agenda: More on momentum, collisions Kinetic and potential energy Potential energy.
Review and then some…. Work & Energy Conservative, Non-conservative, and non-constant Forces.
Ch Ch.15 Term 061. Ch-12  T061  Q16. The volume of a solid Aluminum sphere at the sea level is V = 1.0 m3. This sphere is placed at a depth of.
Springs We are used to dealing with constant forces. Springs are more complicated - not only does the magnitude of the spring force vary, the direction.
Oscillations and Waves An oscillation is a repetitive motion back and forth around a central point which is usually an equilibrium position. A special.
Physics. Simple Harmonic Motion - 3 Session Session Objectives.
1 Work When a force moves something, work is done. Whenever work is done, energy is changed into a different form. Chemical energy → Kinetic energy.
Conservative Forces: The forces is conservative if the work done by it on a particle that moves between two points depends only on these points and not.
Physics. Session Work, Power and Energy - 3 Session Objectives.
Physics 215 – Fall 2014Lecture Welcome back to Physics 215 Today’s agenda: More gravitational potential energy Potential energy of a spring Work-kinetic.
Energy Examples Serway and Jewett 8.1 – 8.3 Physics 1D03 - Lecture 22.
A 19-kg block on a rough horizontal surface is attached to a light spring (force constant = 3.0 kN/m). The block is pulled 6.3 cm to the right from.
Advanced Problems 3 These problems will contain:
Chapter 15 Oscillations. Periodic motion Periodic (harmonic) motion – self-repeating motion Oscillation – periodic motion in certain direction Period.
Chapter 7 Conservation of Energy (cont’d) Mechanical energy conservation Examples Work by non-conservative forces March 4, 2010.
Work and Energy x Work and Energy 06.
Hour Exam 2 Review 9:00 Exam is Tomorrow (Wednesday) at 7:00 pm.
Lecture 12: Elastic Potential Energy & Energy Conservation.
AP Physics Semester Review 26 is torque
An 7.3-kg object rests on the floor of an elevator which is accelerating downward at a rate of 1.0 m/s 2. What is the magnitude of the force the object.
PHY 151: Lecture Motion of an Object attached to a Spring 12.2 Particle in Simple Harmonic Motion 12.3 Energy of the Simple Harmonic Oscillator.
Conservative and Nonconservative Forces. A Force is “Conservative” if: The work it does on an object is available for kinetic energy. These forces store.
60 1. What is the mass M in the system as given in the
Aplications.
1a. Positive and negative work
Chapter 7 Work and Energy
QuickCheck 14.4 A block oscillates on a very long horizontal spring. The graph shows the block’s kinetic energy as a function of position. What is the.
Classical Mechanics Review 4: Units 1-22
Chapter 7 Conservation of Energy (cont’d) Mechanical energy conservation Examples Work by non-conservative forces March 3, /9/2018 Phys 201, Spring.
from rest down a plane inclined at an angle q with the horizontal.
Ch. 10 slides WorkEnergy.ppt.
Student misconceptions
Aim: How do we apply conservation of energy to solving problems?
A mass m = 2.0 kg is attached to a spring having a force constant k = 990 N/m as in the figure. The mass is displaced from its equilibrium position.
AP Physics Review Created by Educational Technology Network
A quick heads up on You will be able to derive it soon… Enquiry:
AP 1 Energy practice.
Last Time: Work, Kinetic Energy, Work-Energy Theorem Today:
Aim: How do we explain conservation of energy?
Potential Energy Problems
Potential Potential Energy
Aim: How do we explain conservation of energy?
OBJECTIVE QUESTIONS FOR NEET AIIMS JIPMER
Work, Energy, Power.
Energy Problems.
Projectile Motion and Spring Problems
T101-Q-1 Figure 1 shows the spring force as a function of position x for a spring-block system resting on a frictionless table. The block is released at.
Ch-15 Help-Session.
Presentation transcript:

A certain pendulum consists of a 2 A certain pendulum consists of a 2.0-kg mass swinging at the end of a string (length = 1.5 m). At the lowest point in the swing the tension in the string is equal to 40 N. To what maximum height above this lowest point will the mass rise during its oscillation? (g = 9.8m/s2) Select the correct answer. 78 cm 32 cm 60 cm 54 cm 33 cm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

55 cm/s 52 cm/s 50 cm/s 53 cm/s 63 cm/s A block (mass = 5.0 kg) sliding on a horizontal frictionless surface is attached to one end of a horizontal spring (k = 100 N/m) which has its other end fixed. If the maximum distance the block slides from the equilibrium position is equal to 21 cm, what is the speed of the block at an instant when it is a distance of 17 cm from the equilibrium position? Select the correct answer. 55 cm/s 52 cm/s 50 cm/s 53 cm/s 63 cm/s 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 18-kg projectile is launched with an initial vertical speed of 18 m/s. It rises to a maximum height of 14 m above the launch point. How much work is done by the dissipative (air) resistive force on the projectile during this ascent? (g = 9.8m/s2) Select the correct answer. - 0.45 kJ - 0.47 kJ - 0.38 kJ - 0.25 kJ - 0.84 kJ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 4. 0-kg block slides down a fixed, rough curved track A 4.0-kg block slides down a fixed, rough curved track. The block has a speed of 3.0 m/s after its height above a horizontal surface has decreased by 1.5 m. Assume the block starts from rest. How much work is done on the block by the force of friction during this descent? (g = 9.8m/s2) Select the correct answer. - 41 J - 44 J - 39 J - 33 J - 28 J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A spring with spring constant k = 500 N/m is extended 18 cm from its equilibrium position. A spring with 6.0 cm of extension from equilibrium will have the same potential energy as the first spring if its spring constant is _____ . Select the correct answer. 4500 N/m 500 N/m 1500 N/m 250 N/m 125 N/m 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 1. 40-kg object tied to the end of a 2 A 1.40-kg object tied to the end of a 2.5-m string swings as a pendulum. At the lowest point of its swing, the object has a kinetic energy of 19 J. Determine the speed of the object at the instant when the string makes an angle of 31° with the vertical. (g = 9.8m/s2) Select the correct answer. 4.5 m/s 9.0 m/s 2.6 m/s 6.7 m/s 3.3 m/s 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 0. 60-kg object is suspended from the ceiling at the end of a 3 A 0.60-kg object is suspended from the ceiling at the end of a 3.0-m string. When pulled to the side and released, it has a speed of 4.0 m/s at the lowest point of its path. What maximum angle does the string make with the vertical as the object swings up? (g = 9.8m/s2) Select the correct answer. 43° 42° 28° 83° 6° 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 19.0-kg block on a horizontal frictionless surface is attached to a light spring (force constant = 2.0 kN/m). The block is initially at rest in its equilibrium position when a force of magnitude P acting parallel to the surface is applied to the block, as shown. When the block is 5.0 cm from the equilibrium position, it has a speed of 0.70 m/s. How much work is done on the block by the force P as the block moves the 5.0 cm? Select the correct answer. 7.2 J 1.4 J 3.8 J 2.7 J 7.3 J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 26-kg block on a horizontal frictionless surface is attached to a light spring (force constant = 0.30 kN/m). The block is initially at rest in its equilibrium position when a force (magnitude P = 80 N) acting parallel to the surface is applied to the block, as shown. What is the speed of the block when it is 12 cm from its equilibrium position? Select the correct answer. 0.76 m/s 0.94 m/s 0.92 m/s 1.09 m/s 0.93 m/s 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A spring (k = 100 N/m) is at the bottom of a frictionless plane that makes an angle of 45° with the horizontal. The upper end of the spring is depressed 0.40 m, and a 1.0-kg block is placed against the depressed spring. The system is then released from rest. What is the kinetic energy of the block at the instant it has traveled 0.40 m and the spring has returned to its uncompressed length? (g = 9.8m/s2) Select the correct answer. 5.2 J 5.5 J 3.8 J 6.1 J 5.6 J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

As a 0.6-kg object moves from point A to point B, it is acted upon by a single conservative force which does -15 J of work during this motion. At point A the speed of the particle is 3.0 m/s and the potential energy associated with the force is + 50 J. What is the potential energy at point B? Select the correct answer. + 65 J + 35 J + 30 J + 54 J + 27 J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 17-kg block on a horizontal surface is attached to a light spring (force constant = 2.0 kN/m). The block is pulled 20 cm to the right from its equilibrium position and released from rest. When the block has moved 8.0 cm toward its equilibrium position, its kinetic energy is 37 J. How much work is done by the frictional force on the block as it moves through the 8.0 cm? Select the correct answer. - 2.6 J - 5.6 J - 8.5 J - 5.8 J - 13 J 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

A 3.0-kg block sliding on a rough horizontal surface is attached to one end of a horizontal spring (k = 300 N/m) which has its other end fixed. The block passes through the equilibrium position with a speed of 7.3 m/s and first comes to rest at a displacement of 0.70 m from equilibrium. What is the coefficient of kinetic friction between the block and the horizontal surface? (g = 9.8m/s2) Select the correct answer. 0.31 0.49 0.24 0.36 0.89 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50