375AST 21/2”-10”. Modification Overview  The stainless steel (ST) series was introduced in 2011.  This version has a stainless steel body. ***(Parts.

Slides:



Advertisements
Similar presentations
350, 350XL 1¼ - 2. Modification Overview Production of the 1¼ began in 2004 and is current. Production of the 1¼ began in 2004 and is current.
Advertisements

RP-500 ½- 1. Modification Overview Production of the RP500 began in 2007 and is current. Production of the RP500 began in 2007 and is current.
RP4A 2½ – 6. Modification Overview Production of the RP4A series began in Production of the RP4A series began in A Lead free version (4ALF)
RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in Production of the RP4AN series began in The 4AN indicates an.
¾”-2”. Modification Overview  Production of the series began in 1989 and is current.  Early models of ¾”-2” series did not always.
RPDA 4A 2½” – 6”. Modification Overview  Production of the RPDA 4A series began in  The RPDA 4A can utilize either a Type I or Type II bypass.
860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”
860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.
350, 350A 2½”-12”. Modification Overview  Production of the 2½ - 10” sizes began in  Production of the “A” models began in This Indicates.
825, 825Y, 825YD 21/2”-10”. Modification Overview  825- ( ) Cast iron body- Threaded in seats- Internal check parts are epoxy coated iron. Old.
975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in This version had buna-n check discs and did not.
975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in  The 975DA uses a ¾” 975XL for the bypass.
765 ½”- 2”. Modification Overview  Production of the 765 began in 1975 and is current.
825Y(YA) 3/4”-2”. Modification Overview  Production of the 825Y began in 1978 and is current.  The 825YR ( ) had replaceable check seats. **
800 (M2,M3,M4) ½”-2”. Modification Overview  The original model 800 was produced from  The 800M2 was produced from  The 800M3.
375, 375XL ¾”-1”. Modification Overview  Production of the ¾”-1” 375 began in 2004 and is current.  The lead free version 375XL was introduced in 2010.
475, 475V 2½”-3”. Modification Overview  Production of the 2½ - 3” sizes began in  The lead free version (XL) was introduced in 2011.
957RPDA, 957N RPDA, 957Z RPDA 21/2”-10”. Modification Overview  Production began in 2002 and is current.  Early versions used a ¾” Flomatic RPZE for.
806, 806YD 3”-10”. Modification Overview  806- ( ) Cast Iron body- Threaded in seats- Internal check parts are epoxy coated iron.  806YD- (1988-present)
LF866 2½”-10”. Product Overview  Production of the 2½” – 10” sizes began in  The LF866 utilizes a Type 2 bypass (Model LF619 single check).
4D-200, 4D-700 2½”- 10”. Modification Overview  Production began in 2003 and was discontinued in  The 4D-700 (RPDA) uses a Type-II bypass (single.
½”-10”. Modification Overview  Production of the series began in 1989 and is current.
007 (M1,M2,M3) ½”-2” 007 (M1,M2,M3) ½”-2”. Modification Overview- 007  007 ¾-1” ( ) 1½ -2” ( ) ½” (1993-Current)  007M1 ¾-1” ( )
009 (M3) ½”-2” 009 (M3) ½”-2”. Modification Overview- 009  009 ¾-1” ( ) (1” ) ¾-1” ( ) (1” ) 1¼ -2” ( ) 1¼.
RPZ 2½”- 10” RPZ 2½”- 10”. Modification Overview  Production of the RPZ in sizes 2½ - 10” began in 1993 and is current.
375, 375XL 1¼” -2”. Modification Overview  Production of the 1¼” -2” 375 began in 2004 and is current.  The lead free version 375XL was introduced in.
RPZ, RPZE ½”-2”. Modification Overview  Production of the model RPZ began in  The lead free version ( RPZE ) was introduced in 2002 and is current.
450 4”-10”. Modification Overview  Production of the 4” - 10” sizes began in  The lead free version (XL) was introduced in 2011.
PVB ¾”- 2”. Modification Overview  Production for the ¾” – 1” PVB began in 1995 and is current.  The body of the ¾” – 1” PVB was modified in July of.
”-10”.
½”-10”.
475, 475V, 475XL 4”-10”.
826YD 21/2”-10”.
009 2½”-3”.
RP4A (LF) ½”-2”.
PVB-4A ½”- 2”.
420, 420XL ¾”-1”.
007 2½”-3”.
RPDA 4AN 21/2” – 6”.
DCDA4A 21/2” – 6”.
DCDA4AN 2½” – 6”.
800 (M2,M3,M4) ½”-2”.
805Y, 805YD 21/2”-10”.
DCV, DCVE ½”-2”.
¾”-2”.
007DCDA 2½”-3”.
½”- 2”.
½”-10”.
806, 806YD 3”-10”.
450 2½”- 3”.
DC4A (LF) ½”-2”.
M500, M500N, M500Z 21/2”-10”.
RPZ-II, RPZE-II ½” , ¾” , 1½”.
4000B (M3) ½”-2”.
850 2½”-10”.
DC-500 ½”- 1”.
350, 350XL ¾”- 1”.
850 (LF) ½”- 2”.
909 21/2”-10”.
DC4A 21/2” – 6”.
880V 21/2”-10”.
975 2½”-10”.
C400, C400N, C400Z 21/2”-10”.
007 2½”-3”.
375DA 2½”-10”.
919 ¾”-2”.
007DCDA 2½”-3”.
M400, M400N, M400Z 21/2”-10”.
DC4AN 2½” – 6”.
450DA 4”-10”.
Presentation transcript:

375AST 21/2”-10”

Modification Overview  The stainless steel (ST) series was introduced in  This version has a stainless steel body. ***(Parts do not interchange with original ductile iron version)

Single Access Cover Removal  Cover is secured by a grooved coupling.  Cover has no spring load.

Check Valve Removal  Check valve module.  21/2”-6” checks are secured by retainers and o-ring sealed.  8”-10” checked are bolted into body and o-ring sealed.  #1 check must be removed before #2 can be removed

#1 Check Valve Removal 21/2”-6”  Plastic Retainer – There is one retainer securing the #1 check module.  Pinch together the exposed ends, push down, and then pull downstream.

#2 Check Valve Removal 21/2”-6”  Wire Retainers – There are two separate spring loaded plate retainers that secure the #2 check module.  Pinch the sides of the spring together and rotate the plates out of the body groove, one side at a time.

Check Valve Removal 21/2”-6”  Once the retainer is removed the check module can be pulled straight out of the body.

Check Valve Removal 8”-12”  #1 check – Remove the 4 nuts and washers.  #2 check – Remove the 7 nuts, washers and the check retaining ring.

Check Disc Replacement  Remove the bolts, washers, and o-rings on the back of the module. ** Do not remove any hardware from the spring side of module. ** Do not remove any hardware from the spring side of module.  Separate the disc retainer from the module.

Check Seat Removal  The check seat is part of the check module and can not be removed.  If the seat is damaged, the complete check module will need to be replaced.

Check Valve Reassembly Notes  21/2-6”- Make sure the rollers on the check module are positioned at 3:00 and 9:00.  8-10” – In the 12:00 and 6:00 position.  Install the check module into the body and close the test cock to hold check in place.

#1 Check Valve Reassembly 21/2”-6”  Plastic Retainer  Install the plastic retainer by inserting one end into the body groove and then sliding your hand around the face of the retainer pushing it into the groove as you go.  The retainer will snap into place when it is fully seated.

#2 Check Valve Reassembly 21/2”-6”  Wire Retainers -  Retainers are positioned at 12:00 and 6:00.  Install each retainer into the body groove one plate at a time.  Squeeze the spring ends together to clear the stops on the face of the seat.

RV Cover Removal  Cover is sealed by the diaphragm.  Remove sensing line.  Cover has a slight spring load.  Hold cover firmly as the bolts are removed.

RV Stem Removal  Gently pull on diaphragm to remove the RV stem.  The spring should fall out when the stem is removed.

RV Seat Removal  The seat is pushed into the body and o-ring sealed.  Simply pull the seat straight out of the body.

RV Stem Disassembly  Remove the retaining bolt and pull apart.

RV Rubber Replacement  The diaphragm and seat disc are free once the RV stem has been disassembled.  The bead and cup of the diaphragm should face toward the bolt end of the stem.  Reassemble stem in reverse order.

RV Reassembly Notes  Form the diaphragm to lay flat against the RV cover.  The bead on the diaphragm will line up with the groove on the RV body.  Replace and lubricate the plunger o-ring.