Internet and Intranet Fundamentals Class 5 Session A

Topics Telnet FTP SMTP NNTP

Telnet Topics Overview History Terminology, Model Commands

Telnet Overview General, bi-directional, byte-oriented communications facility –remote login Interfaces terminal devices and terminal- oriented processes –could also be used for process-process or terminal-terminal communication TCP Application

Telnet History Very early beginning: : Standard –RFC 854 (Postel & Reynolds)

Telnet Terminology, Model NVT = Network Virtual Terminal Negotiated Options Symmetric Treatment of Terminals and Processes

Telnet Terminology, Model NVT –Network Virtual Terminal –standard, intermediate representation of canonical terminal –each end assumed to originate and terminate –user host is host with physical terminal but could just be the host that initiated the communication

Telnet Terminology, Model Principle of Negotiated Options –DO, DONT, WILL, WONT –allows user and server to agree on set of conventions for the Telnet session conventions such as character set, echoing, etc. –either party can initiate a request that some option take effect –other party can accept or reject may refuse to enable; must never refuse to disable

Telnet Terminology, Model Two-Byte or Three-Byte Command Structure –IAC = interpret as command –followed by command code –followed optionally by argument / option Examples: –AYT, AO, GA, WILL, WONT, etc.

Telnet Commands NAME CODE MEANING SE 240 End of subnegotiation parameters. NOP 241 No operation. Data Mark 242 The data stream portion of a Synch. This should always be accompanied by a TCP Urgent notification. Break 243 NVT character BRK. Interrupt Process 244 The function IP. Abort output 245 The function AO. Are You There 246 The function AYT. Erase character 247 The function EC. Erase Line 248 The function EL. Go ahead 249 The GA signal. SB 250 Indicates that what follows is subnegotiation of the indicated option.

Telnet Commands WILL (option code) 251 Indicates the desire to begin performing, or confirmation that you are now performing, the indicated option. WON'T (option code) 252 Indicates the refusal to perform, or continue performing, the indicated option. DO (option code) 253 Indicates the request that the other party perform, or confirmation that you are expecting the other party to perform, the indicated option. DON'T (option code) 254 Indicates the demand that the other party stop performing, or confirmation that you are no longer expecting the other party to perform, the indicated option. IAC 255 Data Byte 255.

FTP File Transfer Protocol Objectives History Terminology, Model Commands Process Relation to Other Application Protocols

Objectives of FTP Promote … file sharing Encourage … indirect / implicit use of remote computers Shield … user from file system variations Facilitate … reliable and efficient data transfer

Objectives of FTP “FTP, though usable directly by a user at a terminal, is designed mainly for use by programs.” -- Postel, Reynolds, RFC 959, October 1985

FTP History MIT 1971 (NCP) –RFC 114 –RFC (NCP) –RFC (TCP) –RFC 765

FTP Terminology data connection –A simplex connection over which data is transferred, in a specified mode and type. DTP –data transfer process server-DTP, user-DTP –active and passive states PI –protocol interpreter server-PI, user-PI

FTP Model

Connections –do not need to exist all of the time –bi-directional User-PI initiates TELNET connection FTP commands sent to server via TELNET –control the data connection Replies sent from server-PI to user-PI via TELNET

FTP Model User-DTP listens (like a server) on data port Data port does not need to be on same host as sender of FTP commands Can transfer data between two remote hosts

FTP Commands Access Control Commands –user –password –quit Transfer Parameter Commands –PORT h1,h2,h3,h4,p1,p2 data port = p1 * p2 –PASV (passive) order server-DTP to listen ordinarily, server-DTP initiates a connection request

FTP Commands RETR STOR APPE DELE CWD LIST

SMTP Simple Mail Transport Protocol Model –at user request, two-way comm channel set up between sender-SMTP and receiver-SMTP –receiver may be ultimate or intermediate –commands are send and replies are received –use Telnet to port 25 try help to see commands

SMTP Receiver-SMTP writes (appends) to file –typically a mailbox file Receiver-SMTP sends replies back to sender-SMTP

SMTP Commands HELO MAIL TO: RCPT FROM: DATA QUIT