Link Quality Source Routing (LQSR) Girish Nandagudi

Reference This presentation is based on the paper “Routing in Multi-Radio, Multi-Hop Wireless Mesh Networks” by Richard Draves, Jitendra Padhye and Brian Zill.

Goal The aim is to improve the network capacity or the performance of individual transfers (by means of an efficient routing algorithm) Challenge – Reduction in total capacity of the network due to interference between multiple simultaneous transmissions Possible solutions – Provide two radios per node, enabling the node to transmit and receive simultaneously – Having two (or more) radios can improve robustness, connectivity and performance – Nodes can utilize more of the radio spectrum.

Other alternative solutions Using directional antennas Improved MACs Channel switching

Diagnosing the multiple radio scenario When the nodes in the network has multiple radios, the shortest path algorithm does not perform optimally. Given a choice between a and an b radio, the shortest path algorithm chooses the slower b radio since it has longer range. A shortest path algorithm that selects the path without ensuring that the hops are on different channels will almost certainly, does not perform well.

Why a new routing metric? Shortest-path routing has several drawbacks when it comes to routing in multi-hop wireless networks. ETX (expected transmission count) metric performs well in single-radio environment, but it does not perform well in environments having different data rates and multiple radios.

ETX ETX uses the underlying packet loss probability, both forward and reverse, denoted by p f and p r respectively to measure the expected number of transmissions including re-transmissions. ETX is denoted by: ETX = Σ k * s(k) = p K = 1 ∞ The path metric is the sum of ETX values for each link in the path. Thereafter, the routing protocol selects the path that has the minimum path metric.

Disadvantages of ETX When we have two radios per node, one radio with an a and the other with b, ETX will transmit the data over b. ETX only considers the loss rates over the links, but not their bandwidths. ETX prefers to transmit over shorter paths, but not on longer paths in order to minimize global resource usage. ETX does not give preference to diverse-channel paths. Hence, it does not perform well in a scenario where two b radios are used.

LQSR protocol New metric, WCETT (Weighted Cumulative Expected Transmission Time) introduced. LQSR is a source-routed link-state protocol derived from DSR. Differences between DSR and the MR-LQSR protocol: DSRMR-LQSR DSR assigns equal weight to all the links in the network. The path metric is simply the sum of link weights along the path. MR-LQSR assigns weight depending on the transmission latency, bandwidth and the channel diversity of the link. DSR implements shortest path routing.MR-LQSR uses the WCETT metric for routing.

LQSR protocol (2) Source-routed, link-state protocol – Derived from DSR Each node measures quality of its link to its neighbor. The info regarding link quality propagates through the mesh (updates in link-state routing). Source selects route with the best cumulative metric. Packets are source-routed using this route.

LQSR: Assumptions All nodes in the network are stationary. Each node is equipped with one or more radio. These can be among a, b and g radios or a mixture of them. The number of radios per node may not always be the same. If a node is equipped with one or more radios, they are tuned to different, non-interfering channels.

LQSR: Design Goals The protocol should take both loss rate and bandwidth of a link into account while considering it for inclusion in the path. The path metric should be increasing. That is, if an hop is added to the existing path, the cost of the path should never decrease. The path metric should account for the reduction in throughput due to interference among links that operate on the same channel.

The protocol assigns a weight to each link that is equal to the expected amount of time it would take to successfully transmit a packet of some fixed size S. This time depends on the link bandwidth and loss rate. Now, the ETT of a link i between x and y nodes is denoted by ETT i Using the above notation, the WCETT can be derived as: Computing path metric WCETT = Σ ETT i i = 1 n

Computing path metric II It is desirable for the WCETT to consider the impact of channel diversity. In a two-hop path, if the hops are interfering, then the effective bandwidth of the channel is reduced to half due to the fact that only one hop can operate at a time. The assumption that the hops that are nearby and in the same channel always interfere holds almost true for short paths, but it might be somewhat pessimistic for longer paths.

Computing path metric III Assuming a n hop path and that the system has a total of k channels, we define X j as: X j = Σ ETT i 1≤j ≤k Hop i is on channel j WCETT is taken as max(X j ).

Computing path metric IV The metric, WCETT = max(X j ) favors paths along diverse channels. This metric achieves the third design goal, but not the second design goal. To achieve both the design goals, we can combine the two equations as follows: WCETT = (1 – β) * Σ ETT i + β * max X j i = 1 n 1≤j ≤k

Interpreting the expression Two possible ways: 1. The first term reflects the sum of the transmission times along all hops in the network. The second term reflects the set of all hops that will have the most impact on the throughput of this path. 2. We can view the equation as a tradeoff between throughput and delay.

Measuring ETT ETT is defined as bandwidth-adjusted ETX Hence, ETT is given by – ETT = ETX * (S / B) To accurately calculate the ETT, we need to know the forward and reverse loss rates (p f and p r ) and the bandwidth of each link. This can be achieved by using broadcast packet technique described by De Couto et al [2].

Measuring ETT - Determining bandwidth Determining bandwidth is complex. One possibility is to set the bandwidth of each radio to a fixed value. Another possibility is to allow radios to select the bandwidth automatically by enabling them to operate at autorate mode.

Measuring ETT - Determining bandwidth II The technique of packet pairs is used in this case to determine the bandwidth. Each node sends a back-to-back probe packet of sizes 137 bytes and 1137 bytes to each of its neighbor every minute. The neighbor measures the time difference between the receipt of the first and the second packet and communicates it back to the sender. The sender takes the minimum 10 consecutive samples and estimates the bandwidth by dividing the size of the second probe packet by the minimum sample. N1 Sender N2 N3 N4 P1P2 P1P2 P1P2 P1P2

Implementation of MR-LQSR Implemented in an ad-hoc routing framework called the Mesh Connectivity Layer (MCL). MCL is a loadable windows driver and implements a virtual network adapter within. To the rest of the system, the ad-hoc network appears as an additional network link. It internally routes the packets using the LQSR protocol. IPv4IPv6IPX… MCL (with LQSR and WCETT) Ethernet … Note: The above diagram has been borrowed from [1]

Implementation - Advantages Higher layer software runs unmodified over the ad-hoc network. Hence, no modification to the network stack is required. The virtual MCL network adapter can multiplex several physical network adapters. Hence, the ad-hoc routing runs over heterogeneous link layers.

Testing The implementation has been tested on a testbed consisting of 23 wireless nodes. The testbed is located in an office floor and the nodes are placed in cubicles, conference rooms and labs. All nodes are HP machines with latest configuration and with Microsoft Windows XP as their operating system. Each node has two radios connected to the PC via PCD-TP-202CS PCI-to-Cardbus adapter cards and each node has a NetGear WAG 511 or NetGear WAB 501 card.

Testbed… Note: The above diagram has been borrowed from [1]

Results The results have been classified as – Accuracy of bandwidth estimation – Baseline scenario – Single radio – Two radios – The impact of β – Two simultaneous connections

Results - Accuracy of bandwidth estimation Two of the testbed nodes were used. The time between successive pair of packets was 2 seconds. Each bandwidth estimate was obtained by taking the minimum of 50 such pairs. The estimation is not accurate for higher rates. Note: The above diagram has been borrowed from [1]

Results - Baseline scenario - Single radio Out of 506 sender-receiver pairs, 100 pairs were picked at random. A 2-minute TCP transfer was carried out between the selected pair of nodes. The experiment was carried out for WCETT, ETX and for basic shortest-path routing. Since each node had a single radio, the throughput difference between the three protocols were not that significant. Note: The above diagram has been borrowed from [1]

Results – Two radios One a radio and one g radio per node was used. The same TCP transfer was used with the parameter β set to 0.5 for WCETT. As shown in the figure, WCETT outperformed the other protocols by a huge margin. This is due to the fact that WCETT takes into consideration the channel diversity of the link too in addition to bandwidth of the link. Note: The above diagram has been borrowed from [1]

Results – One and two radios Note: The above diagram has been borrowed from [1]

Results - The impact of β β plays an important role in the WCETT calculation. When β is set to 0, WCETT selects the link based only on the ETT or the latency, without regard to the channel diversity. Setting the value of β to 1 makes little sense. The metric selects the paths with less channel diversity when β is low. Note: The above diagram has been borrowed from [1]

Results - Two simultaneous connections For WCETT metric, the experiment was repeated four times with β = 0, 0.1, 0.5 and 0.9. The measured median throughput was multiplied by 2 since there were two connections. The product was called the Multiplied Median Throughput (MMT). It must be noted that WCETT performs better than ETX for all values of β. The conclusion is that at higher loads, the throughput is maximized by having lower values of β. Note: The above diagram has been borrowed from [1]

Related work One way to improve the capacity of wireless networks is by using improved MAC. – To exploit multiple non-interfering frequency channels. An alternative way to improve the capacity is to stripe traffic over multiple network interfaces. Another approach is to use directional antennas. The capacity of wireless network can also be improved by taking advantage of full spectrum by using rapid channel switching. – This can be quiet slow with the existing hardware. – Can be implemented if hardware support is achieved.

Conclusion It is shown that when nodes are equipped with multiple heterogeneous radios, it is important to select channel diverse paths in addition to taking care of latency and bandwidth for links. The results show that WCETT outperforms the existing protocols in this particular scenario where channel diversity is involved. WCETT is flexible in the sense that it allows us to tradeoff the channel diversity by setting the value for β. The implementation calls for no change in hardware or the networking software. This allows the user to seamlessly use this protocol with the existing system setup.

References [1] Richard Draves, Jitendra Padhye and Brian Zill “Routing in Multi-Radio, Multi-Hop Wireless Mesh Networks” [2] D. De Couto, D. Aguayo, J. Bicket, and R. Morris: "High-throughput path metric for multi-hop wireless routing", In MOBICOM, 2003.